Thanks guys, I'll keep an eye on the repository and grab a copy once things are finalised.
On Wednesday, 10 May 2017 15:29:22 UTC+1, RobertCNelson wrote: > > I just pushed another sync up: P8_31 was mising ecap. ;) > > > https://github.com/beagleboard/bb.org-overlays/commit/6197c268c1b875a2c066635413c9742b720762bc > > > I'm going to do a quick space -> tab conversion on cape-universal*.dts > as i need to also sync all the eqep options with 12 or so > univ-<board>-<enable>.dts > > Regards, > > On Wed, May 10, 2017 at 9:01 AM, Drew Fustini <[email protected] > <javascript:>> wrote: > > I actually ran into this too recently and have modified > > cape-universala-00A0.dts to enable pins P8_33 and P8_35 for eqep1: > > https://github.com/beagleboard/bb.org-overlays/pull/46 > > > > Thanks > > Drew > > > > On May 10, 2017 7:29 AM, "Hugh Frater" <[email protected] <javascript:>> > wrote: > >> > >> Found it - cape-universal doesn't support eqep1, this was added to > >> cape-universalh 4 months ago but the code wasn't merged into > cape-universal. > >> I will look at doing this now. > >> > >> On Wednesday, 10 May 2017 10:20:56 UTC+1, Hugh Frater wrote: > >>> > >>> Anyone? > >>> > >>> On Thursday, 20 April 2017 15:01:07 UTC+1, Hugh Frater wrote: > >>>> > >>>> Following on from my earlier messages related to this, I am using > >>>> cape-universal now to setup and control the pins for my mechatronics > >>>> project. Pinmap constraints mean I need to use eQEP1 and eQEP2. eQEP2 > on > >>>> P8_11, P8_12 and P8_16 is working, but I can't get config-pin to > setup eQEP1 > >>>> on P8_31, P8_33 and P8_35. > >>>> > >>>> root@beaglebone:/dev# config-pin -l P8_31 > >>>> default gpio gpio_pu gpio_pd uart qep > >>>> > >>>> You can see qep is a supported mode. > >>>> > >>>> root@beaglebone:/dev# config-pin P8_31 qep > >>>> bash: line 0: echo: write error: No such device > >>>> Cannot write pinmux file: > >>>> /sys/devices/platform/ocp/ocp:P8_31_pinmux/state > >>>> > >>>> And that is the error I get... > >>>> > >>>> Does anyone know what is going on here? This 2nd encoder input is the > >>>> last bit of the pinmux'ing puzzle I need to sort out, all the other > GPIO is > >>>> working nicely now. > >>>> > >>>> Thanks, Hugh > >>>> > >> -- > >> For more options, visit http://beagleboard.org/discuss > >> --- > >> You received this message because you are subscribed to the Google > Groups > >> "BeagleBoard" group. > >> To unsubscribe from this group and stop receiving emails from it, send > an > >> email to [email protected] <javascript:>. > >> To view this discussion on the web visit > >> > https://groups.google.com/d/msgid/beagleboard/2cbad167-27c6-44b0-aea2-e423cca25dd1%40googlegroups.com. > > > >> For more options, visit https://groups.google.com/d/optout. > > > > -- > > For more options, visit http://beagleboard.org/discuss > > --- > > You received this message because you are subscribed to the Google > Groups > > "BeagleBoard" group. > > To unsubscribe from this group and stop receiving emails from it, send > an > > email to [email protected] <javascript:>. > > To view this discussion on the web visit > > > https://groups.google.com/d/msgid/beagleboard/CAEf4M_D9ytOfzome-NbXGJ6oObebsBO8en_OcVW9XqiygqoVsw%40mail.gmail.com. > > > > > > For more options, visit https://groups.google.com/d/optout. > > > > -- > Robert Nelson > https://rcn-ee.com/ > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/14a712d3-98de-42c9-8a4f-44f49c6856e1%40googlegroups.com. For more options, visit https://groups.google.com/d/optout.
