On Mon, Mar 26, 2018 at 5:56 PM, <[email protected]> wrote: > Sorry, please disregard the uBoot output posted previously--that was with > our workaround of loading one big dtbo file. > > HERE IS THE OUTPUT FROM OUR MULTIPLE DTBOs... > > > U-Boot SPL 2018.01-00002-g9aa111a004 (Jan 20 2018 - 12:45:29) > Trying to boot from MMC1 > > > U-Boot 2018.01-00002-g9aa111a004 (Jan 20 2018 - 12:45:29 -0600), Build: > jenkins-github_Bootloader-Builder-32 > > CPU : AM335X-GP rev 2.1 > I2C: ready > DRAM: 512 MiB > No match for driver 'omap_hsmmc' > No match for driver 'omap_hsmmc' > Some drivers were not found > Reset Source: Power-on reset has occurred. > MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 > Using default environment > > Board: BeagleBone Black > <ethaddr> not set. Validating first E-fuse MAC > BeagleBone Black: > BeagleBone: cape eeprom: i2c_probe: 0x54: > BeagleBone: cape eeprom: i2c_probe: 0x55: > BeagleBone: cape eeprom: i2c_probe: 0x56: > BeagleBone: cape eeprom: i2c_probe: 0x57: > Net: eth0: MII MODE > cpsw, usb_ether > Press SPACE to abort autoboot in 2 seconds > board_name=[A335BNLT] ... > board_rev=[00C0] ... > switch to partitions #0, OK > mmc0 is current device > SD/MMC found on device 0 > ** Bad device 0:2 0x82000000 ** > ** Bad device 0:2 0x82000000 ** > switch to partitions #0, OK > mmc0 is current device > Scanning mmc 0:1... > gpio: pin 56 (gpio 56) value is 0 > gpio: pin 55 (gpio 55) value is 0 > gpio: pin 54 (gpio 54) value is 0 > gpio: pin 53 (gpio 53) value is 1 > switch to partitions #0, OK > mmc0 is current device > gpio: pin 54 (gpio 54) value is 1 > Checking for: /uEnv.txt ... > 2094 bytes read in 30 ms (67.4 KiB/s) > gpio: pin 55 (gpio 55) value is 1 > Loaded environment from /uEnv.txt > Importing environment from mmc ... > Checking if uenvcmd is set ... > Checking if client_ip is set ... > Checking for: /boot.scr ... > Checking for: /boot/boot.scr ... > Checking for: /boot/uEnv.txt ... > gpio: pin 55 (gpio 55) value is 1 > 2246 bytes read in 28 ms (78.1 KiB/s) > Loaded environment from /boot/uEnv.txt > debug: [dtb=am335x-boneblack-overlay.dtb] ... > Using: dtb=am335x-boneblack-overlay.dtb ... > Checking if uname_r is set in /boot/uEnv.txt... > gpio: pin 56 (gpio 56) value is 1 > Running uname_boot ... > loading /boot/vmlinuz-4.4.91-ti-r133 ... > 8886912 bytes read in 579 ms (14.6 MiB/s) > uboot_overlays: dtb=am335x-boneblack-overlay.dtb in /boot/uEnv.txt, unable > to use [uboot_base_dtb=am335x-boneblack-uboot.dtb] ... > loading /boot/dtbs/4.4.91-ti-r133/am335x-boneblack-overlay.dtb ... > 54603 bytes read in 84 ms (634.8 KiB/s) > uboot_overlays: [fdt_buffer=0x60000] ... > uboot_overlays: loading /lib/firmware/maps_bbb_gpio-00A0.dtbo ... > 1039 bytes read in 145 ms (6.8 KiB/s) > uboot_overlays: loading /lib/firmware/maps_bbb_pwm-00A0.dtbo ... > 1599 bytes read in 296 ms (4.9 KiB/s) > uboot_overlays: loading /lib/firmware/maps_bbb_i2c-00A0.dtbo ... > 1312 bytes read in 300 ms (3.9 KiB/s) > uboot_overlays: loading /lib/firmware/maps_bbb_eqep-00A0.dtbo ... > 2055 bytes read in 396 ms (4.9 KiB/s)
Okay these loaded fine.. > uboot_overlays: uboot loading of [/lib/firmware/BB-BONE-eMMC1-01-00A0.dtbo] > disabled by /boot/uEnv.txt [disable_uboot_overlay_emmc=1]... > uboot_overlays: uboot loading of [/lib/firmware/BB-HDMI-TDA998x-00A0.dtbo] > disabled by /boot/uEnv.txt [disable_uboot_overlay_video=1]... > uboot_overlays: uboot loading of [/lib/firmware/BB-ADC-00A0.dtbo] disabled > by /boot/uEnv.txt [disable_uboot_overlay_adc=1]... > uboot_overlays: loading /lib/firmware/AM335X-PRU-RPROC-4-4-TI-00A0.dtbo ... > 2402 bytes read in 356 ms (5.9 KiB/s) > uboot_overlays: cape universal disabled, external cape enabled or > detected... > loading /boot/initrd.img-4.4.91-ti-r133 ... > 5416133 bytes read in 361 ms (14.3 MiB/s) > debug: [console=ttyO0,115200n8 bone_capemgr.uboot_capemgr_enabled=1 > root=/dev/mmcblk0p1 ro rootfstype=ext4 rootwait coherent_pool=1M > net.ifnames=0 quiet cape_universal=enable] ... > debug: [bootz 0x82000000 0x88080000:52a4c5 88000000] ... > ## Flattened Device Tree blob at 88000000 > Booting using the fdt blob at 0x88000000 > Loading Ramdisk to 8fad5000, end 8ffff4c5 ... OK > reserving fdt memory region: addr=88000000 size=6e000 > Loading Device Tree to 8fa64000, end 8fad4fff ... OK > > Starting kernel ... > > [ 0.000833] clocksource_probe: no matching clocksources found > [ 2.077791] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc handle > [ 2.249328] omap_voltage_late_init: Voltage driver support not added > [ 2.257414] PM: Cannot get wkup_m3_ipc handle > > Debian GNU/Linux 9 beaglebone ttyS0 > > BeagleBoard.org Debian Image 2017-10-10 > > Support/FAQ: http://elinux.org/Beagleboard:BeagleBoneBlack_Debian > > default username:password is [debian:temppwd] > > beaglebone login: root > Password: > Last login: Mon Mar 26 15:39:43 PDT 2018 from 172.23.49.123 on pts/0 > Linux beaglebone 4.4.91-ti-r133 #1 SMP Tue Oct 10 05:18:08 UTC 2017 armv7l Everything looks good, if the nodes arn't showing up, can you share the 4 overlays source? Regards, -- Robert Nelson https://rcn-ee.com/ -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/CAOCHtYg5DGgUz0mDRXEjM1%2BuBufsiRVchz3PnvOE0YkgsKhq%2Bw%40mail.gmail.com. For more options, visit https://groups.google.com/d/optout.
