Hello,
My Beaglebone Black has problems booting with an sd card made following the
guide:
https://eewiki.net/display/linuxonarm/BeagleBone+Black#BeagleBoneBlack-RemovemicroSD/SDcard
am33x-rt-v4.14 (Longterm 4.14.x + Real-Time Linux)
debian-9.3-minimal-armhf-2017-12-09
When compiling the kernel i have made following changes:
CONFIG_SND_SOC_WM8731=y
CONFIG_NETWORK_PHY_TIMESTAMPING=y
CONFIG_PTP_1588_CLOCK=y
The booting process goes on for some time until it gets stuck. I can not
log in.
I have attached the log from the serial connnection output. Please let me
know if any other information will help figuring out what the problem could
be.
I will be grateful for any help.
Thank you,
Mikkel Pihl
U-Boot SPL 2018.03-dirty (May 23 2018 - 11:57:41 +0200)
Trying to boot from MMC1
Loading Environment from EXT4... ** File not found /boot/uboot.env **
** Unable to read "/boot/uboot.env" from mmc0:1 **
Failed (-5)
U-Boot 2018.03-dirty (May 23 2018 - 11:57:41 +0200)
CPU : AM335X-GP rev 2.1
I2C: ready
DRAM: 512 MiB
No match for driver 'omap_hsmmc'
No match for driver 'omap_hsmmc'
Some drivers were not found
Reset Source: Power-on reset has occurred.
RTC 32KCLK Source: External.
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
Loading Environment from EXT4... ** File not found /boot/uboot.env **
** Unable to read "/boot/uboot.env" from mmc0:1 **
Failed (-5)
Board: BeagleBone Black
<ethaddr> not set. Validating first E-fuse MAC
BeagleBone Black:
BeagleBone: cape eeprom: i2c_probe: 0x54:
BeagleBone: cape eeprom: i2c_probe: 0x55:
BeagleBone: cape eeprom: i2c_probe: 0x56:
BeagleBone: cape eeprom: i2c_probe: 0x57:
Net: eth0: MII MODE
cpsw, usb_ether
Press SPACE to abort autoboot in 2 seconds
board_name=[A335BNLT] ...
board_rev=[000C] ...
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
** Bad device 0:2 0x82000000 **
** Bad device 0:2 0x82000000 **
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
gpio: pin 56 (gpio 56) value is 0
gpio: pin 55 (gpio 55) value is 0
gpio: pin 54 (gpio 54) value is 0
gpio: pin 53 (gpio 53) value is 1
switch to partitions #0, OK
mmc0 is current device
gpio: pin 54 (gpio 54) value is 1
Checking for: /uEnv.txt ...
Checking for: /boot.scr ...
Checking for: /boot/boot.scr ...
Checking for: /boot/uEnv.txt ...
gpio: pin 55 (gpio 55) value is 1
28 bytes read in 16 ms (1000 Bytes/s)
Loaded environment from /boot/uEnv.txt
Checking if uname_r is set in /boot/uEnv.txt...
gpio: pin 56 (gpio 56) value is 1
Running uname_boot ...
loading /boot/vmlinuz-4.14.42-bone-rt-r14 ...
10281472 bytes read in 666 ms (14.7 MiB/s)
loading /boot/dtbs/4.14.42-bone-rt-r14/am335x-boneblack.dtb ...
60851 bytes read in 46 ms (1.3 MiB/s)
uboot_overlays: add [enable_uboot_overlays=1] to /boot/uEnv.txt to enable...
debug: [console=ttyO0,115200n8 root=/dev/mmcblk0p1 ro rootfstype=ext4
rootwait] ...
debug: [bootz 0x82000000 - 0x88000000] ...
## Flattened Device Tree blob at 88000000
Booting using the fdt blob at 0x88000000
Loading Device Tree to 8ffee000, end 8ffffdb2 ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.14.42-bone-rt-r14 (mp@mp-VirtualBox) (gcc
version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #1 PREEMPT RT Wed May 23
15:45:23 C8
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7),
cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
instruction cache
[ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] efi: Getting EFI parameters from FDT:
[ 0.000000] efi: UEFI not found.
[ 0.000000] cma: Reserved 48 MiB at 0x9d000000
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] AM335X ES2.1 (sgx neon)
[ 0.000000] random: get_random_bytes called from start_kernel+0xac/0x454
with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920
[ 0.000000] Kernel command line: console=ttyO0,115200n8
root=/dev/mmcblk0p1 ro rootfstype=ext4 rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 0.000000] Memory: 447480K/524288K available (13312K kernel code, 1052K
rwdata, 4208K rodata, 1024K init, 690K bss, 27656K reserved, 49152K
cma-reserved,)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0e00000 (14304 kB)
[ 0.000000] .init : 0xc1400000 - 0xc1500000 (1024 kB)
[ 0.000000] .data : 0xc1500000 - 0xc16073f4 (1053 kB)
[ 0.000000] .bss : 0xc16115ec - 0xc16be1c4 ( 691 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] ftrace: allocating 41506 entries in 122 pages
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] No expedited grace period (rcu_normal_after_boot).
[ 0.000000] Tasks RCU enabled.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128
interrupts
[ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz
[ 0.000016] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every
89478484971ns
[ 0.000028] clocksource: timer1: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 79635851949 ns
[ 0.000035] OMAP clocksource: timer1 at 24000000 Hz
[ 0.000489] timer_probe: no matching timers found
[ 0.000702] Console: colour dummy device 80x30
[ 0.000834] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0'
[ 0.000836] This ensures that you still see kernel messages. Please
[ 0.000838] update your kernel commandline.
[ 0.000857] Calibrating delay loop... 995.32 BogoMIPS (lpj=1990656)
[ 0.047015] pid_max: default: 32768 minimum: 301
[ 0.047280] Security Framework initialized
[ 0.047291] Yama: becoming mindful.
[ 0.047375] AppArmor: AppArmor initialized
[ 0.047587] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.047597] Mountpoint-cache hash table entries: 1024 (order: 0, 4096
bytes)
[ 0.048591] CPU: Testing write buffer coherency: ok
[ 0.049477] Setting up static identity map for 0x80100000 - 0x80100060
[ 0.049758] Hierarchical SRCU implementation.
[ 0.052958] EFI services will not be available.
[ 0.054534] devtmpfs: initialized
[ 0.068798] VFP support v0.3: implementor 41 architecture 3 part 30
variant c rev 3
[ 0.069255] clocksource: jiffies: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.069283] futex hash table entries: 256 (order: 1, 8192 bytes)
[ 0.073204] xor: measuring software checksum speed
[ 0.111169] arm4regs : 1219.000 MB/sec
[ 0.151044] 8regs : 957.000 MB/sec
[ 0.191043] 32regs : 1053.000 MB/sec
[ 0.191052] xor: using function: arm4regs (1219.000 MB/sec)
[ 0.191074] pinctrl core: initialized pinctrl subsystem
[ 0.191843] DMI not present or invalid.
[ 0.192360] NET: Registered protocol family 16
[ 0.195592] DMA: preallocated 256 KiB pool for atomic coherent
allocations
[ 0.212864] omap_hwmod: debugss: _wait_target_disable failed
[ 0.258459] OMAP GPIO hardware version 0.1
[ 0.270963] No ATAGs?
[ 0.270982] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.351325] raid6: int32x4 gen() 327 MB/s
[ 0.419222] raid6: int32x4 xor() 246 MB/s
[ 0.419232] raid6: using algorithm int32x4 gen() 327 MB/s
[ 0.419240] raid6: .... xor() 246 MB/s, rmw enabled
[ 0.419247] raid6: using intx1 recovery algorithm
[ 0.426401] edma 49000000.edma: TI EDMA DMA engine driver
[ 0.428682] SCSI subsystem initialized
[ 0.429402] usbcore: registered new interface driver usbfs
[ 0.429473] usbcore: registered new interface driver hub
[ 0.429610] usbcore: registered new device driver usb
[ 0.430094] omap_i2c 44e0b000.i2c: could not find pctldev for node
/ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c0_pins, deferring
probe
[ 0.431504] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz
[ 0.431802] media: Linux media interface: v0.10
[ 0.431857] Linux video capture interface: v2.00
[ 0.431922] pps_core: LinuxPPS API ver. 1 registered
[ 0.431930] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo
Giometti <giome...@linux.it>
[ 0.431964] PTP clock support registered
[ 0.432084] dmi: Firmware registration failed.
[ 0.432494] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400
[ 0.433222] Advanced Linux Sound Architecture Driver Initialized.
[ 0.434630] NetLabel: Initializing
[ 0.434649] NetLabel: domain hash size = 128
[ 0.434655] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 0.434762] NetLabel: unlabeled traffic allowed by default
[ 0.435633] clocksource: Switched to clocksource timer1
[ 0.603162] VFS: Disk quotas dquot_6.6.0
[ 0.603267] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096
bytes)
[ 0.604122] AppArmor: AppArmor Filesystem Enabled
[ 0.615055] NET: Registered protocol family 2
[ 0.616111] TCP established hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.616179] TCP bind hash table entries: 4096 (order: 4, 98304 bytes)
[ 0.616367] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.616508] UDP hash table entries: 256 (order: 2, 16384 bytes)
[ 0.616551] UDP-Lite hash table entries: 256 (order: 2, 16384 bytes)
[ 0.616812] NET: Registered protocol family 1
[ 0.617541] RPC: Registered named UNIX socket transport module.
[ 0.617561] RPC: Registered udp transport module.
[ 0.617568] RPC: Registered tcp transport module.
[ 0.617574] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.618565] hw perfevents: no interrupt-affinity property for /pmu,
guessing.
[ 0.618693] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5
counters available
[ 0.621343] audit: initializing netlink subsys (disabled)
[ 0.622496] audit: type=2000 audit(0.620:1): state=initialized
audit_enabled=0 res=1
[ 0.622629] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.628385] zbud: loaded
[ 0.631416] NFS: Registering the id_resolver key type
[ 0.631471] Key type id_resolver registered
[ 0.631479] Key type id_legacy registered
[ 0.631500] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.631968] fuse init (API version 7.26)
[ 0.632895] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 0.633086] orangefs_init: module version upstream loaded
[ 0.633097] SGI XFS with ACLs, security attributes, realtime, no debug
enabled
[ 0.643199] Key type asymmetric registered
[ 0.643224] Asymmetric key parser 'x509' registered
[ 0.643360] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 245)
[ 0.643606] io scheduler noop registered
[ 0.643618] io scheduler deadline registered
[ 0.644211] io scheduler cfq registered (default)
[ 0.644224] io scheduler mq-deadline registered
[ 0.645324] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size
568
[ 0.646329] gpio-of-helper ocp:cape-universal: ready
[ 0.648951] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc handle
[ 0.650172] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[ 0.653625] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 30,
base_baud = 3000000) is a 8250
[ 1.439769] console [ttyS0] enabled
[ 1.446019] omap_rng 48310000.rng: Random Number Generator ver. 20
[ 1.453181] [drm] Initialized vgem 1.0.0 20120112 for virtual device on
minor 0
[ 1.460669] usbcore: registered new interface driver udl
[ 1.468506] at24 2-0054: 32768 byte 24c256 EEPROM, writable, 1
bytes/write
[ 1.475809] at24 2-0055: 32768 byte 24c256 EEPROM, writable, 1
bytes/write
[ 1.482994] at24 2-0056: 32768 byte 24c256 EEPROM, writable, 1
bytes/write
[ 1.490158] at24 2-0057: 32768 byte 24c256 EEPROM, writable, 1
bytes/write
[ 1.499796] libphy: Fixed MDIO Bus: probed
[ 1.504730] CAN device driver interface
[ 1.559750] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus
freq 1000000
[ 1.567461] davinci_mdio 4a101000.mdio: detected phy mask fffffffe
[ 1.574075] davinci_mdio: dt: updated phy_id[0] from phy_mask[fffffffe]
[ 1.582339] libphy: 4a101000.mdio: probed
[ 1.586425] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00,
driver SMSC LAN8710/LAN8720
[ 1.596560] cpsw 4a100000.ethernet: Detected MACID = 50:65:83:c6:02:29
[ 1.603374] cpsw 4a100000.ethernet: cpts: overflow check period 1250
(jiffies)
[ 1.612646] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.619275] ehci-platform: EHCI generic platform driver
[ 1.624712] ehci-omap: OMAP-EHCI Host Controller driver
[ 1.630179] usbcore: registered new interface driver usb-storage
[ 1.638299] am335x-phy-driver 47401300.usb-phy: 47401300.usb-phy supply
vcc not found, using dummy regulator
[ 1.650611] am335x-phy-driver 47401b00.usb-phy: 47401b00.usb-phy supply
vcc not found, using dummy regulator
[ 1.674017] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as
rtc0
[ 1.682411] i2c /dev entries driver
[ 1.688317] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60
sec
[ 1.695788] softdog: initialized. soft_noboot=0 soft_margin=60 sec
soft_panic=0 (nowayout=1)
[ 1.705564] omap_hsmmc 48060000.mmc: Got CD GPIO
[ 1.789352] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
[ 1.798502] omap-aes 53500000.aes: will run requests pump with realtime
priority
[ 1.810796] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
[ 1.818462] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.824694] usbcore: registered new interface driver usbhid
[ 1.826271] mmc0: host does not support reading read-only switch,
assuming write-enable
[ 1.829304] mmc0: new high speed SDHC card at address aaaa
[ 1.835812] mmcblk0: mmc0:aaaa SC32G 29.7 GiB
[ 1.838692] mmcblk0: p1
[ 1.853678] usbhid: USB HID core driver
[ 1.857992] remoteproc remoteproc0: wkup_m3 is available
[ 1.868138] NET: Registered protocol family 10
[ 1.874443] Segment Routing with IPv6
[ 1.878247] mip6: Mobile IPv6
[ 1.881242] NET: Registered protocol family 17
[ 1.885809] can: controller area network core (rev 20170425 abi 9)
[ 1.886126] mmc1: new high speed MMC card at address 0001
[ 1.891717] mmcblk1: mmc1:0001 M62704 3.56 GiB
[ 1.891993] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB
[ 1.895723] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB
[ 1.895936] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB
[ 1.897429] mmcblk1: p1
[ 1.927153] NET: Registered protocol family 29
[ 1.931772] Key type dns_resolver registered
[ 1.936067] mpls_gso: MPLS GSO support
[ 1.940019] omap_voltage_late_init: Voltage driver support not added
[ 1.946420] ThumbEE CPU extension supported.
[ 1.950726] Registering SWP/SWPB emulation handler
[ 1.956404] registered taskstats version 1
[ 1.960671] zswap: loaded using pool lzo/zbud
[ 1.967149] Btrfs loaded, crc32c=crc32c-generic
[ 1.971818] AppArmor: AppArmor sha1 policy hashing enabled
[ 1.977350] ima: No TPM chip found, activating TPM-bypass! (rc=-19)
[ 2.022774] input: tps65217_pwr_but as
/devices/platform/ocp/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0
[ 2.034050] tps65217 0-0024: TPS65217 ID 0xe version 1.2
[ 2.039911] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1
bytes/write
[ 2.170121] tda998x 0-0070: found TDA19988
[ 2.175462] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_ops)
[ 2.181522] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 2.188169] [drm] No driver support for vblank timestamp query.
[ 2.194686] [drm] Cannot find any crtc or sizes
[ 2.200005] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on
minor 1
[ 2.207577] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz
[ 2.214623] remoteproc remoteproc0: powering up wkup_m3
[ 2.219940] remoteproc remoteproc0: Booting fw image
am335x-pm-firmware.elf, size 217168
[ 2.220624] bone_capemgr bone_capemgr: Baseboard:
'A335BNLT,000C,1727BBBG1061'
[ 2.220644] bone_capemgr bone_capemgr:
compatible-baseboard=ti,beaglebone-black - #slots=4
[ 2.243978] remoteproc remoteproc0: remote processor wkup_m3 is now up
[ 2.244008] wkup_m3_ipc 44e11324.wkup_m3_ipc: CM3 Firmware Version =
0x193
[ 2.257504] bone_capemgr bone_capemgr: slot #0: No cape found
[ 2.287689] bone_capemgr bone_capemgr: slot #1: No cape found
[ 2.319898] bone_capemgr bone_capemgr: slot #2: No cape found
[ 2.352050] bone_capemgr bone_capemgr: slot #3: No cape found
[ 2.357883] bone_capemgr bone_capemgr: initialized OK.
[ 2.373416] musb-hdrc musb-hdrc.1: MUSB HDRC host driver
[ 2.378809] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus
number 1
[ 2.386577] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.393404] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 2.400661] usb usb1: Product: MUSB HDRC host driver
[ 2.405649] usb usb1: Manufacturer: Linux 4.14.42-bone-rt-r14 musb-hcd
[ 2.412206] usb usb1: SerialNumber: musb-hdrc.1
[ 2.417553] hub 1-0:1.0: USB hub found
[ 2.421393] hub 1-0:1.0: 1 port detected
[ 2.428732] hdmi-audio-codec hdmi-audio-codec.0.auto: ASoC: no source
widget found for Playback
[ 2.437573] hdmi-audio-codec hdmi-audio-codec.0.auto: ASoC: Failed to
add route Playback -> direct -> TX
[ 2.447849] asoc-simple-card sound: i2s-hifi <-> 48038000.mcasp mapping
ok
[ 2.454799] asoc-simple-card sound: ASoC: no DMI vendor name!
[ 2.462336] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01
00:00:00 UTC (946684800)
[ 2.471013] of_cfs_init
[ 2.473651] of_cfs_init: OK
[ 2.477095] ALSA device list:
[ 2.480097] #0: TI BeagleBone Black
[ 2.489923] EXT4-fs (mmcblk0p1): INFO: recovery required on readonly
filesystem
[ 2.497324] EXT4-fs (mmcblk0p1): write access will be enabled during
recovery
[ 2.560767] EXT4-fs (mmcblk0p1): recovery complete
[ 2.569746] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data
mode. Opts: (null)
[ 2.577978] VFS: Mounted root (ext4 filesystem) readonly on device 179:1.
[ 2.596015] devtmpfs: mounted
[ 2.602758] Freeing unused kernel memory: 1024K
[ 3.031974] systemd[1]: System time before build time, advancing clock.
[ 3.133576] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.156037] random: systemd: uninitialized urandom read (16 bytes read)
[ 3.166182] random: systemd: uninitialized urandom read (16 bytes read)
[ 3.184605] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT
+SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT
+GNUTLS +AC)
[ 3.200069] [drm] Cannot find any crtc or sizes
[ 3.208227] systemd[1]: Detected architecture arm.
Welcome to Debian GNU/Linux 9 (stretch)!
[ 3.231236] systemd[1]: Set hostname to <arm>.
[ 3.440205] random: systemd-cryptse: uninitialized urandom read (16
bytes read)
[ 3.882314] systemd[1]: Created slice System Slice.
[ OK ] Created slice System Slice.
[ 3.901428] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ 3.925100] systemd[1]: Mounting Debug File System...
Mounting Debug File System...
[ 3.948665] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 3.968719] systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
[ 3.988843] systemd[1]: Listening on Journal Audit Socket.
[ OK ] Listening on Journal Audit Socket.
[ 4.008378] systemd[1]: Reached target Swap.
[ OK ] Reached target Swap.
[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ OK ] Listening on Syslog Socket.
[ OK ] Reached target Remote File Systems.
[ OK ] Created slice User and Session Slice.
[ OK ] Reached target Slices.
[ OK ] Created slice system-getty.slice.
Mounting POSIX Message Queue File System...
[ OK ] Listening on Journal Socket.
Starting Create list of required st��…ce nodes for the current
kernel...
Starting Load Kernel Modules...
[ OK ] Started Forward Password Requests to Wall Directory Watch.
Starting Journal Service...
[ OK ] Listening on fsck to fsckd communication Socket.
Starting File System Check on Root Device...
[ OK ] Set up automount Arbitrary Executab��…rmats File System Automount
Point.
[ OK ] Listening on udev Control Socket.
[ OK ] Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Reached target Paths.
[ OK ] Reached target Encrypted Volumes.
[ OK ] Mounted POSIX Message Queue File System.
[ OK ] Mounted Debug File System.
[ OK ] Started Create list of required sta��…vice nodes for the current
kernel.
[ OK ] Started Load Kernel Modules.
[ OK ] Started File System Check Daemon to report status.
Mounting Configuration File System...
Starting Apply Kernel Variables...
Mounting FUSE Control File System...
Starting Create Static Device Nodes in /dev...
[ OK ] Mounted FUSE Control File System.
[ OK ] Mounted Configuration File System.
[ OK ] Started Journal Service.
[ OK ] Started File System Check on Root Device.
[ OK ] Started Apply Kernel Variables.
[ OK ] Started Create Static Device Nodes in /dev.
Starting udev Kernel Device Manager...
Starting Remount Root and Kernel File Systems...
[ 5.105693] EXT4-fs (mmcblk0p1): re-mounted. Opts: errors=remount-ro
[ OK ] Started Remount Root and Kernel File Systems.
Starting Flush Journal to Persistent Storage...
Starting udev Coldplug all Devices...
[ OK ] Reached target Local File Systems (Pre).
[ OK ] Reached target Local File Systems.
Starting Raise network interfaces...
Starting Load/Save Random Seed...
[ OK ] Started udev Kernel Device Manager.
[ 5.464759] systemd-journald[146]: Received request to flush runtime
journal from PID 1
[ OK ] Started Load/Save Random Seed.
[ OK ] Started Flush Journal to Persistent Storage.
Starting Create Volatile Files and Directories...
[ OK ] Started Create Volatile Files and Directories.
Starting Update UTMP about System Boot/Shutdown...
Starting Network Time Synchronization...
[ OK ] Started Update UTMP about System Boot/Shutdown.
[ OK ] Started Network Time Synchronization.
[ OK ] Reached target System Time Synchronized.
[ 7.287957] net eth0: initializing cpsw version 1.12 (0)
[ 7.297426] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4
[ 7.321746] cpsw 4a100000.ethernet: ALE Table size 1024
[ 7.417121] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver
[SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL)
[ 7.467072] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ OK ] Started udev Coldplug all Devices.
[ OK ] Reached target System Initialization.
[ OK ] Started Daily apt download activities.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
[ OK ] Started Daily apt upgrade and clean activities.
[ OK ] Reached target Timers.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
Starting DUN service...
Starting LSB: Load kernel modules needed to enable cpufreq
scaling...
Starting Cape Manager Service...
Starting System Logging Service...
[ OK ] Started Regular background program processing daemon.
Starting Generic Board Startup...
Starting LSB: Start busybox udhcpd at boot time...
Starting Telephony service...
[ OK ] Started D-Bus System Message Bus.
[ OK ] Started Telephony service.
[ OK ] Started DUN service.
Starting Connection service...
Starting Avahi mDNS/DNS-SD Stack...
Starting Login Service...
[ OK ] Started System Logging Service.
[ OK ] Started Cape Manager Service.
[ OK ] Started LSB: Start busybox udhcpd at boot time.
[ 9.505295] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full -
flow control off
[ OK ] Started Avahi mDNS/DNS-SD Stack.
[ 9.545903] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ OK ] Started Connection service.
[ OK ] Started Login Service.
[ 9.800818] Bluetooth: Core ver 2.22
[ 9.811530] NET: Registered protocol family 31
[ 9.840647] Bluetooth: HCI device and connection manager initialized
[ 9.861208] Bluetooth: HCI socket layer initialized
[ 9.879155] Bluetooth: L2CAP socket layer initialized
[ 9.904125] Bluetooth: SCO socket layer initialized
[ 10.238488] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[ OK ] Started LSB: Load kernel modules needed to enable cpufreq scaling.
Starting LSB: set CPUFreq kernel parameters...
Starting WPA supplicant...
[ OK ] Started LSB: set CPUFreq kernel parameters.
[ 11.450141] using random self ethernet address
[ 11.454695] using random host ethernet address
[ 11.528120] 8021q: 802.1Q VLAN Support v1.8
[ 11.551167] 8021q: adding VLAN 0 to HW filter on device eth0
Starting Hostname Service...
[ 11.685800] using random self ethernet address
[ 11.690669] using random host ethernet address
[ OK ] Started WPA supplicant.
[ 11.952094] usb0: HOST MAC 50:65:83:c6:02:2a
[ 11.975932] usb0: MAC 50:65:83:c6:02:2b
[ 12.005488] usb1: HOST MAC 50:65:83:c6:02:2d
[ 12.033508] usb1: MAC 50:65:83:c6:02:2e
[ OK ] Started Hostname Service.
[ 12.375014] configfs-gadget gadget: high-speed config #1: c
[ OK ] Found device /dev/ttyS0.
[ 12.508684] IPv6: ADDRCONF(NETDEV_UP): usb1: link is not ready
Stopping LSB: Start busybox udhcpd at boot time...
[ OK ] Stopped LSB: Start busybox udhcpd at boot time.
[ OK ] Started Raise network interfaces.
[ OK ] Reached target Network.
Starting Permit User Sessions...
Starting dnsmasq - A lightweight DHCP and caching DNS server...
Starting OpenBSD Secure Shell server...
[ OK ] Reached target Network is Online.
Starting LSB: Advanced IEEE 802.11 management daemon...
[ OK ] Started Permit User Sessions.
[ OK ] Started Serial Getty on ttyS0.
[ OK ] Started Getty on tty1.
[ OK ] Reached target Login Prompts.
[ OK ] Started LSB: Advanced IEEE 802.11 management daemon.
[ OK ] Started OpenBSD Secure Shell server.
[ OK ] Started dnsmasq - A lightweight DHCP and caching DNS server.
[ OK ] Reached target Host and Network Name Lookups.
Starting The Apache HTTP Server...
[ OK ] Started The Apache HTTP Server.
[ OK ] Reached target Sound Card.
[ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
[ OK ] Found device /dev/ttyGS0.
[ OK ] Started Serial Getty on ttyGS0.
[ OK ] Started Generic Board Startup.
[ OK ] Reached target Multi-User System.
[ OK ] Reached target Graphical Interface.
Starting Update UTMP about System Runlevel Changes...
[ OK ] Started Update UTMP about System Runlevel Changes.
--
For more options, visit http://beagleboard.org/discuss
---
You received this message because you are subscribed to the Google Groups
"BeagleBoard" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to beagleboard+unsubscr...@googlegroups.com.
To view this discussion on the web visit
https://groups.google.com/d/msgid/beagleboard/d962533d-7866-47f7-89e5-ed3c58bfcb7a%40googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
