Here is the output of dmesg and ifconfig: debian@beaglebone:~$ dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.49-ti-r54 (root@b2-am57xx-beagle-x15-2gb) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 SMP PREEMPT Fri Jun 15 22:14:13 UTC 2018 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x PocketBeagle [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 48 MiB at 0x9c800000 [ 0.000000] On node 0 totalpages: 130560 [ 0.000000] free_area_init_node: node 0, pgdat c15ed380, node_mem_map df961000 [ 0.000000] Normal zone: 1148 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 130560 pages, LIFO batch:31 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] random: get_random_bytes called from start_kernel+0xac/0x460 with crng_init=0 [ 0.000000] percpu: Embedded 18 pages/cpu @df900000 s41548 r8192 d23988 u73728 [ 0.000000] pcpu-alloc: s41548 r8192 d23988 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/mmcblk0p1 ro rootfstype=ext4 rootwait coherent_pool=1M net.ifnames=0 quiet [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 440624K/522240K available (13312K kernel code, 1168K rwdata, 4372K rodata, 1024K init, 673K bss, 32464K reserved, 49152K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xe0000000 - 0xff800000 ( 504 MB) lowmem : 0xc0000000 - 0xdfe00000 ( 510 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc0e00000 (14304 kB) .init : 0xc1400000 - 0xc1500000 (1024 kB) .data : 0xc1500000 - 0xc16241a8 (1169 kB) .bss : 0xc162ec1c - 0xc16d709c ( 674 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] ftrace: allocating 42794 entries in 126 pages [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Tasks RCU enabled. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000020] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000041] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000052] OMAP clocksource: timer1 at 24000000 Hz [ 0.001528] timer_probe: no matching timers found [ 0.001764] Console: colour dummy device 80x30 [ 0.001791] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' [ 0.001796] This ensures that you still see kernel messages. Please [ 0.001800] update your kernel commandline. [ 0.001824] Calibrating delay loop... 995.32 BogoMIPS (lpj=1990656) [ 0.025876] pid_max: default: 32768 minimum: 301 [ 0.026152] Security Framework initialized [ 0.026167] Yama: becoming mindful. [ 0.026208] AppArmor: AppArmor disabled by boot time parameter [ 0.026403] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.026416] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.027441] CPU: Testing write buffer coherency: ok [ 0.027944] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.041966] Setting up static identity map for 0x80100000 - 0x80100060 [ 0.049875] Hierarchical SRCU implementation. [ 0.061007] EFI services will not be available. [ 0.065882] smp: Bringing up secondary CPUs ... [ 0.065899] smp: Brought up 1 node, 1 CPU [ 0.065910] SMP: Total of 1 processors activated (995.32 BogoMIPS). [ 0.065917] CPU: All CPU(s) started in SVC mode. [ 0.067504] devtmpfs: initialized [ 0.098178] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.098638] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.098663] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.102651] xor: measuring software checksum speed [ 0.141900] arm4regs : 1217.000 MB/sec [ 0.181849] 8regs : 1091.000 MB/sec [ 0.221848] 32regs : 1088.000 MB/sec [ 0.261847] neon : 1669.000 MB/sec [ 0.261855] xor: using function: neon (1669.000 MB/sec) [ 0.261875] pinctrl core: initialized pinctrl subsystem [ 0.262691] DMI not present or invalid. [ 0.263142] NET: Registered protocol family 16 [ 0.267025] DMA: preallocated 1024 KiB pool for atomic coherent allocations [ 0.328887] omap_hwmod: debugss: _wait_target_disable failed [ 0.381691] cpuidle: using governor menu [ 0.387911] OMAP GPIO hardware version 0.1 [ 0.411064] No ATAGs? [ 0.411086] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.411966] omap4_sram_init:Unable to allocate sram needed to handle errata I688 [ 0.411980] omap4_sram_init:Unable to get sram pool needed to handle errata I688 [ 0.505905] raid6: neonx2 gen() 1883 MB/s [ 0.573872] raid6: neonx2 xor() 1497 MB/s [ 0.573879] raid6: using algorithm neonx2 gen() 1883 MB/s [ 0.573885] raid6: .... xor() 1497 MB/s, rmw enabled [ 0.573892] raid6: using neon recovery algorithm [ 0.581988] edma 49000000.edma: TI EDMA DMA engine driver [ 0.587324] SCSI subsystem initialized [ 0.590034] libata version 3.00 loaded. [ 0.590326] usbcore: registered new interface driver usbfs [ 0.590387] usbcore: registered new interface driver hub [ 0.590505] usbcore: registered new device driver usb [ 0.591378] omap_i2c 44e0b000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c0_pins, deferring probe [ 0.592316] omap_i2c 4802a000.i2c: bus 1 rev0.11 at 400 kHz [ 0.593100] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 400 kHz [ 0.593501] media: Linux media interface: v0.10 [ 0.593573] Linux video capture interface: v2.00 [ 0.593743] pps_core: LinuxPPS API ver. 1 registered [ 0.593751] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giome...@linux.it> [ 0.593772] PTP clock support registered [ 0.594087] dmi: Firmware registration failed. [ 0.594593] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 [ 0.598271] Advanced Linux Sound Architecture Driver Initialized. [ 0.598964] NetLabel: Initializing [ 0.598974] NetLabel: domain hash size = 128 [ 0.598979] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.599075] NetLabel: unlabeled traffic allowed by default [ 0.602377] clocksource: Switched to clocksource timer1 [ 0.768643] VFS: Disk quotas dquot_6.6.0 [ 0.768780] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.781326] NET: Registered protocol family 2 [ 0.782252] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.782298] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.782463] TCP: Hash tables configured (established 4096 bind 4096) [ 0.782597] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.782619] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.782843] NET: Registered protocol family 1 [ 0.791756] RPC: Registered named UNIX socket transport module. [ 0.791766] RPC: Registered udp transport module. [ 0.791771] RPC: Registered tcp transport module. [ 0.791776] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.792570] Unpacking initramfs... [ 1.018439] random: fast init done [ 1.041175] Freeing initrd memory: 3940K [ 1.041756] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 1.041981] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 1.044224] audit: initializing netlink subsys (disabled) [ 1.045460] audit: type=2000 audit(1.044:1): state=initialized audit_enabled=0 res=1 [ 1.045591] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 1.051500] zbud: loaded [ 1.058865] NFS: Registering the id_resolver key type [ 1.058913] Key type id_resolver registered [ 1.058919] Key type id_legacy registered [ 1.058937] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.059279] fuse init (API version 7.26) [ 1.060168] orangefs_debugfs_init: called with debug mask: :none: :0: [ 1.060369] orangefs_init: module version upstream loaded [ 1.060378] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 1.071145] Key type asymmetric registered [ 1.071161] Asymmetric key parser 'x509' registered [ 1.071286] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243) [ 1.075618] io scheduler noop registered [ 1.075630] io scheduler deadline registered [ 1.076015] io scheduler cfq registered (default) [ 1.076026] io scheduler mq-deadline registered [ 1.078265] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 1.086854] gpio-of-helper ocp:cape-universal: ready [ 1.093318] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc handle [ 1.095424] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled [ 1.099146] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 30, base_baud = 3000000) is a 8250 [ 1.115499] console [ttyS0] enabled [ 1.116646] 48022000.serial: ttyS1 at MMIO 0x48022000 (irq = 31, base_baud = 3000000) is a 8250 [ 1.117612] 48024000.serial: ttyS2 at MMIO 0x48024000 (irq = 32, base_baud = 3000000) is a 8250 [ 1.118735] 481a8000.serial: ttyS4 at MMIO 0x481a8000 (irq = 33, base_baud = 3000000) is a 8250 [ 1.121859] omap_rng 48310000.rng: Random Number Generator ver. 20 [ 1.123265] [drm] Initialized vgem 1.0.0 20120112 for virtual device on minor 0 [ 1.123370] usbcore: registered new interface driver udl [ 1.171252] libphy: Fixed MDIO Bus: probed [ 1.172118] CAN device driver interface [ 1.173401] c_can_platform 481cc000.can: c_can_platform device registered (regs=fa1cc000, irq=39) [ 1.174346] c_can_platform 481d0000.can: c_can_platform device registered (regs=fa1d0000, irq=40) [ 1.177387] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.177445] ehci-platform: EHCI generic platform driver [ 1.177762] ehci-omap: OMAP-EHCI Host Controller driver [ 1.178715] usbcore: registered new interface driver usb-storage [ 1.181680] am335x-phy-driver 47401300.usb-phy: 47401300.usb-phy supply vcc not found, using dummy regulator [ 1.188182] am335x-phy-driver 47401b00.usb-phy: 47401b00.usb-phy supply vcc not found, using dummy regulator [ 1.204309] omap_rtc 44e3e000.rtc: registered as rtc0 [ 1.205571] i2c /dev entries driver [ 1.209400] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 1.210000] softdog: initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=1) [ 1.211678] cpuidle: enable-method property 'ti,am3352' found operations [ 1.212455] sdhci: Secure Digital Host Controller Interface driver [ 1.212463] sdhci: Copyright(c) Pierre Ossman [ 1.213376] omap_hsmmc 48060000.mmc: Got CD GPIO [ 1.252793] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.257248] ledtrig-cpu: registered to indicate activity on CPUs [ 1.257845] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 [ 1.258216] omap-aes 53500000.aes: will run requests pump with realtime priority [ 1.260939] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 [ 1.267987] hidraw: raw HID events driver (C) Jiri Kosina [ 1.268687] usbcore: registered new interface driver usbhid [ 1.268697] usbhid: USB HID core driver [ 1.269305] remoteproc remoteproc0: wkup_m3 is available [ 1.271364] ti_am3359-tscadc 44e0d000.tscadc: chan 0 step_avg truncating to 16 [ 1.271380] ti_am3359-tscadc 44e0d000.tscadc: chan 1 step_avg truncating to 16 [ 1.271389] ti_am3359-tscadc 44e0d000.tscadc: chan 2 step_avg truncating to 16 [ 1.271396] ti_am3359-tscadc 44e0d000.tscadc: chan 3 step_avg truncating to 16 [ 1.271404] ti_am3359-tscadc 44e0d000.tscadc: chan 4 step_avg truncating to 16 [ 1.271412] ti_am3359-tscadc 44e0d000.tscadc: chan 5 step_avg truncating to 16 [ 1.271420] ti_am3359-tscadc 44e0d000.tscadc: chan 6 step_avg truncating to 16 [ 1.271427] ti_am3359-tscadc 44e0d000.tscadc: chan 7 step_avg truncating to 16 [ 1.276288] wireguard: WireGuard 0.0.20180531 loaded. See www.wireguard.com for information. [ 1.276301] wireguard: Copyright (C) 2015-2018 Jason A. Donenfeld < ja...@zx2c4.com>. All Rights Reserved. [ 1.277130] NET: Registered protocol family 10 [ 1.282951] Segment Routing with IPv6 [ 1.283054] mip6: Mobile IPv6 [ 1.283072] NET: Registered protocol family 17 [ 1.283091] can: controller area network core (rev 20170425 abi 9) [ 1.283235] NET: Registered protocol family 29 [ 1.283370] Key type dns_resolver registered [ 1.283377] mpls_gso: MPLS GSO support [ 1.283388] NET: Registered protocol family 44 [ 1.283708] omap_voltage_late_init: Voltage driver support not added [ 1.290699] ThumbEE CPU extension supported. [ 1.290725] Registering SWP/SWPB emulation handler [ 1.291666] registered taskstats version 1 [ 1.291822] zswap: loaded using pool lzo/zbud [ 1.294244] Btrfs loaded, crc32c=crc32c-generic [ 1.294530] ima: No TPM chip found, activating TPM-bypass! (rc=-19) [ 1.294556] ima: Allocated hash algorithm: sha256 [ 1.332866] mmc0: host does not support reading read-only switch, assuming write-enable [ 1.335954] mmc0: new high speed SDHC card at address aaaa [ 1.337223] mmcblk0: mmc0:aaaa SA08G 7.40 GiB [ 1.340152] mmcblk0: p1 [ 1.344351] input: tps65217_pwr_but as /devices/platform/ocp/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 [ 1.344929] tps65217 0-0024: TPS65217 ID 0xe version 1.2 [ 1.345392] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.345504] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 1.350529] remoteproc remoteproc0: powering up wkup_m3 [ 1.350557] remoteproc remoteproc0: Booting fw image am335x-pm-firmware.elf, size 217168 [ 1.350808] remoteproc remoteproc0: remote processor wkup_m3 is now up [ 1.350832] wkup_m3_ipc 44e11324.wkup_m3_ipc: CM3 Firmware Version = 0x193 [ 1.351936] musb-hdrc musb-hdrc.0: MUSB HDRC host driver [ 1.351976] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 1 [ 1.352329] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.352340] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.352348] usb usb1: Product: MUSB HDRC host driver [ 1.352356] usb usb1: Manufacturer: Linux 4.14.49-ti-r54 musb-hcd [ 1.352364] usb usb1: SerialNumber: musb-hdrc.0 [ 1.353351] hub 1-0:1.0: USB hub found [ 1.353442] hub 1-0:1.0: 1 port detected [ 1.359333] musb-hdrc musb-hdrc.1: MUSB HDRC host driver [ 1.359372] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 2 [ 1.359674] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.359685] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.359694] usb usb2: Product: MUSB HDRC host driver [ 1.359702] usb usb2: Manufacturer: Linux 4.14.49-ti-r54 musb-hcd [ 1.359709] usb usb2: SerialNumber: musb-hdrc.1 [ 1.360612] hub 2-0:1.0: USB hub found [ 1.360711] hub 2-0:1.0: 1 port detected [ 1.364856] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 1.364878] of_cfs_init [ 1.365058] of_cfs_init: OK [ 1.366651] ALSA device list: [ 1.366664] No soundcards found. [ 1.371438] Freeing unused kernel memory: 1024K [ 1.513403] musb-hdrc musb-hdrc.1: VBUS_ERROR in a_wait_vrise (81, <SessEnd), retry #1, port1 00000104 [ 1.522172] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 1.523288] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 1.523401] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 1.665828] musb-hdrc musb-hdrc.1: VBUS_ERROR in a_wait_vrise (81, <SessEnd), retry #2, port1 00000104 [ 1.818256] musb-hdrc musb-hdrc.1: VBUS_ERROR in a_wait_vrise (81, <SessEnd), retry #3, port1 00000104 [ 1.970681] musb-hdrc musb-hdrc.1: VBUS_ERROR in a_wait_vrise (80, <SessEnd), retry #3, port1 0008010c [ 16.153288] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 16.697006] systemd[1]: System time before build time, advancing clock. [ 16.783132] ip_tables: (C) 2000-2006 Netfilter Core Team [ 16.828757] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [ 16.829506] systemd[1]: Detected architecture arm. [ 16.831500] systemd[1]: Set hostname to <beaglebone>. [ 17.480661] systemd[1]: Created slice User and Session Slice. [ 17.481862] systemd[1]: Listening on Journal Audit Socket. [ 17.482613] systemd[1]: Listening on udev Control Socket. [ 17.482903] systemd[1]: Reached target Swap. [ 17.483096] systemd[1]: Reached target Remote File Systems. [ 17.483618] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 17.484096] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ 18.505428] EXT4-fs (mmcblk0p1): re-mounted. Opts: errors=remount-ro [ 19.026989] systemd-journald[617]: Received request to flush runtime journal from PID 1 [ 23.874139] nf_conntrack version 0.5.0 (8192 buckets, 32768 max) [ 25.961491] random: crng init done [ 25.961512] random: 7 urandom warning(s) missed due to ratelimiting [ 56.963895] systemd[1]: apt-daily.timer: Adding 10h 33min 44.566844s random time. [ 58.708397] systemd[1]: apt-daily.timer: Adding 10h 25min 49.043704s random time. [ 63.032737] using random self ethernet address [ 63.032757] using random host ethernet address [ 63.086865] using random self ethernet address [ 63.086885] using random host ethernet address [ 63.221391] Mass Storage Function, version: 2009/09/11 [ 63.221416] LUN: removable file: (no medium) [ 63.331539] usb0: HOST MAC 98:5d:ad:d6:8c:cd [ 63.331908] usb0: MAC 98:5d:ad:d6:8c:ce [ 63.341984] usb1: HOST MAC 98:5d:ad:d6:8c:d0 [ 63.342345] usb1: MAC 98:5d:ad:d6:8c:d1 [ 63.793232] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready [ 63.905947] IPv6: ADDRCONF(NETDEV_UP): usb1: link is not ready [ 66.349657] systemd[1]: apt-daily.timer: Adding 10h 22min 47.337827s random time. [ 68.476273] pruss 4a300000.pruss: creating PRU cores and other child platform devices [ 68.548093] remoteproc remoteproc1: 4a334000.pru is available [ 68.548262] pru-rproc 4a334000.pru: PRU rproc node /ocp/pruss_soc_bus@4a326004/pruss@0/pru@34000 probed successfully [ 68.549882] remoteproc remoteproc2: 4a338000.pru is available [ 68.549983] pru-rproc 4a338000.pru: PRU rproc node /ocp/pruss_soc_bus@4a326004/pruss@0/pru@38000 probed successfully
debian@beaglebone:~$ ifconfig lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 1000 (Local Loopback) RX packets 9440 bytes 637920 (622.9 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 9440 bytes 637920 (622.9 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 usb0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500 inet 192.168.7.2 netmask 255.255.255.252 broadcast 192.168.7.3 ether 98:5d:ad:d6:8c:ce txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 usb1: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500 inet 192.168.6.2 netmask 255.255.255.252 broadcast 192.168.6.3 ether 98:5d:ad:d6:8c:d1 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 On Sat, Sep 8, 2018 at 2:22 PM Anouar Raddaoui <aradd...@uncc.edu> wrote: > Yes. > Here is the UART log when booting up: > > > U-Boot SPL 2018.03-00002-gac9cce7c6a (Apr 05 2018 - 13:07:46 -0500) > Trying to boot from MMC1 > Loading Environment from EXT4... ** File not found /boot/uboot.env ** > > ** Unable to read "/boot/uboot.env" from mmc0:1 ** > Failed (-5) > > > U-Boot 2018.03-00002-gac9cce7c6a (Apr 05 2018 - 13:07:46 -0500), Build: > jenkins- > github_Bootloader-Builder-47 > > CPU : AM335X-GP rev 2.1 > I2C: ready > DRAM: 512 MiB > No match for driver 'omap_hsmmc' > No match for driver 'omap_hsmmc' > Some drivers were not found > Reset Source: Power-on reset has occurred. > RTC 32KCLK Source: Internal. > MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 > Loading Environment from EXT4... ** File not found /boot/uboot.env ** > > ** Unable to read "/boot/uboot.env" from mmc0:1 ** > Failed (-5) > Model: BeagleBoard.org PocketBeagle > <ethaddr> not set. Validating first E-fuse MAC > Net: usb_ether > Press SPACE to abort autoboot in 2 seconds > board_name=[A335PBGL] ... > switch to partitions #0, OK > mmc0 is current device > SD/MMC found on device 0 > ** Bad device 0:2 0x82000000 ** > ** Bad device 0:2 0x82000000 ** > switch to partitions #0, OK > mmc0 is current device > Scanning mmc 0:1... > gpio: pin 56 (gpio 56) value is 0 > gpio: pin 55 (gpio 55) value is 0 > gpio: pin 54 (gpio 54) value is 0 > gpio: pin 53 (gpio 53) value is 1 > switch to partitions #0, OK > mmc0 is current device > gpio: pin 54 (gpio 54) value is 1 > Checking for: /uEnv.txt ... > Checking for: /boot.scr ... > Checking for: /boot/boot.scr ... > Checking for: /boot/uEnv.txt ... > gpio: pin 55 (gpio 55) value is 1 > 2086 bytes read in 67 ms (30.3 KiB/s) > Loaded environment from /boot/uEnv.txt > Checking if uname_r is set in /boot/uEnv.txt... > gpio: pin 56 (gpio 56) value is 1 > Running uname_boot ... > loading /boot/vmlinuz-4.14.49-ti-r54 ... > 10453504 bytes read in 713 ms (14 MiB/s) > loading /boot/dtbs/4.14.49-ti-r54/am335x-pocketbeagle.dtb ... > 124183 bytes read in 130 ms (932.6 KiB/s) > uboot_overlays: [fdt_buffer=0x60000] ... > uboot_overlays: loading /lib/firmware/AM335X-PRU-RPROC-4-14-TI-00A0.dtbo > ... > 3513 bytes read in 520 ms (5.9 KiB/s) > loading /boot/initrd.img-4.14.49-ti-r54 ... > 4034122 bytes read in 319 ms (12.1 MiB/s) > debug: [console=ttyO0,115200n8 root=/dev/mmcblk0p1 ro rootfstype=ext4 > rootwait c > oherent_pool=1M net.ifnames=0 > quiet] ... > debug: [bootz 0x82000000 0x88080000:3d8e4a 88000000] ... > ## Flattened Device Tree blob at 88000000 > Booting using the fdt blob at 0x88000000 > Loading Ramdisk to 8fc27000, end 8ffffe4a ... OK > reserving fdt memory region: addr=88000000 size=7f000 > Loading Device Tree to 8fba5000, end 8fc26fff ... OK > > Starting kernel ... > > [ 0.001516] timer_probe: no matching timers found > [ 0.614027] dmi: Firmware registration failed. > [ 1.112814] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc handle > [ 1.303794] omap_voltage_late_init: Voltage driver support not added > [ 1.990560] musb-hdrc musb-hdrc.1: VBUS_ERROR in a_wait_vrise (80, > <SessEnd), > retry #3, port1 0008010c > > Debian GNU/Linux 9 beaglebone ttyS0 > > BeagleBoard.org Debian Image 2018-06-17 > > Support/FAQ: http://elinux.org/Beagleboard:BeagleBoneBlack_Debian > > default username:password is [debian:temppwd] > > beaglebone login: debian > Password: > Last login: Mon Aug 6 22:12:03 UTC 2018 on ttyS0 > > The programs included with the Debian GNU/Linux system are free software; > the exact distribution terms for each program are described in the > individual files in /usr/share/doc/*/copyright. > > Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent > permitted by applicable law. > debian@beaglebone:~$ > > > On Sat, Sep 8, 2018 at 2:05 PM Pablo Rodriguez <pabloar1...@gmail.com> > wrote: > >> Hi. The schematic of the USB0 is the same as they pocket? >> >> El sáb., 8 de sep. de 2018 2:15 PM, An Ra <aradd...@uncc.edu> escribió: >> >>> >>> Hi all, >>> >>> I have a custom board (based on PocketBeagle design). I was able to >>> flash the EEPROM and it boots up normally and I have access to the Linux >>> command Line through UART0 interface. However, the board doesn't show up as >>> a USB device as the PocketBeagle does. >>> >>> Any ideas how to solve this issue? >>> >>> Regards, >>> >>> -- >>> For more options, visit http://beagleboard.org/discuss >>> --- >>> You received this message because you are subscribed to the Google >>> Groups "BeagleBoard" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to beagleboard+unsubscr...@googlegroups.com. >>> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/beagleboard/c7212090-ca58-4196-9063-1cd05e355903%40googlegroups.com >>> <https://groups.google.com/d/msgid/beagleboard/c7212090-ca58-4196-9063-1cd05e355903%40googlegroups.com?utm_medium=email&utm_source=footer> >>> . >>> For more options, visit https://groups.google.com/d/optout. >>> >> -- >> For more options, visit http://beagleboard.org/discuss >> --- >> You received this message because you are subscribed to the Google Groups >> "BeagleBoard" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to beagleboard+unsubscr...@googlegroups.com. >> To view this discussion on the web visit >> https://groups.google.com/d/msgid/beagleboard/CAEObdD1yPX_z4CVrmO3AbsZ0F93t4833RQ56ic%3DUz7rwDCP3Bw%40mail.gmail.com >> <https://groups.google.com/d/msgid/beagleboard/CAEObdD1yPX_z4CVrmO3AbsZ0F93t4833RQ56ic%3DUz7rwDCP3Bw%40mail.gmail.com?utm_medium=email&utm_source=footer> >> . >> For more options, visit https://groups.google.com/d/optout. >> > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to beagleboard+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/CAJPgcaWHy05DQUEkTiedxODgEz3ckrJtLSOTebo02w1U6dKTWg%40mail.gmail.com. For more options, visit https://groups.google.com/d/optout.