Yeah!!!! That worked!!! After 2-3 months I can finally update this stupid thing.
Here's the full boot from J1. I don have a couple questions at the end. U-Boot SPL 2018.01-00002-g9aa111a004 (Jan 20 2018 - 12:45:29) Trying to boot from MMC2 U-Boot 2018.01-00002-g9aa111a004 (Jan 20 2018 - 12:45:29 -0600), Build: jenkins-github_Bootloader-Builder-32 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Global warm SW reset has occurred. Reset Source: Power-on reset has occurred. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Using default environment Board: BeagleBone Black <ethaddr> not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds board_name=[A335BNLT] ... board_rev=[00C0] ... Card did not respond to voltage select! mmc_init: -95, time 12 Card did not respond to voltage select! mmc_init: -95, time 13 Card did not respond to voltage select! mmc_init: -95, time 13 gpio: pin 56 (gpio 56) value is 0 gpio: pin 55 (gpio 55) value is 0 gpio: pin 54 (gpio 54) value is 0 gpio: pin 53 (gpio 53) value is 1 Card did not respond to voltage select! mmc_init: -95, time 13 Card did not respond to voltage select! mmc_init: -95, time 13 switch to partitions #0, OK mmc1(part 0) is current device Scanning mmc 1:1... gpio: pin 56 (gpio 56) value is 0 gpio: pin 55 (gpio 55) value is 0 gpio: pin 54 (gpio 54) value is 0 gpio: pin 53 (gpio 53) value is 1 switch to partitions #0, OK mmc1(part 0) is current device gpio: pin 54 (gpio 54) value is 1 Checking for: /uEnv.txt ... Checking for: /boot.scr ... Checking for: /boot/boot.scr ... Checking for: /boot/uEnv.txt ... gpio: pin 55 (gpio 55) value is 1 2295 bytes read in 15 ms (149.4 KiB/s) Loaded environment from /boot/uEnv.txt Checking if uname_r is set in /boot/uEnv.txt... gpio: pin 56 (gpio 56) value is 1 Running uname_boot ... loading /boot/vmlinuz-4.9.105-ti-r114 ... 9818560 bytes read in 637 ms (14.7 MiB/s) uboot_overlays: [uboot_base_dtb=am335x-boneblack-uboot.dtb] ... uboot_overlays: Switching too: dtb=am335x-boneblack-uboot.dtb ... loading /boot/dtbs/4.9.105-ti-r114/am335x-boneblack-uboot.dtb ... 61638 bytes read in 43 ms (1.4 MiB/s) uboot_overlays: [fdt_buffer=0x60000] ... uboot_overlays: loading /lib/firmware/BB-BONE-eMMC1-01-00A0.dtbo ... 1440 bytes read in 173 ms (7.8 KiB/s) uboot_overlays: loading /lib/firmware/BB-HDMI-TDA998x-00A0.dtbo ... 4896 bytes read in 60 ms (79.1 KiB/s) uboot_overlays: loading /lib/firmware/BB-ADC-00A0.dtbo ... 711 bytes read in 142 ms (4.9 KiB/s) uboot_overlays: loading /lib/firmware/univ-bbb-EVA-00A0.dtbo ... 62064 bytes read in 240 ms (252 KiB/s) loading /boot/initrd.img-4.9.105-ti-r114 ... 5799056 bytes read in 382 ms (14.5 MiB/s) debug: [console=ttyO0,115200n8 bone_capemgr.uboot_capemgr_enabled=1 root=/dev/mmcblk1p1 ro rootfstype=ext4 rootwait coherent_pool=1M net.ifnames=0] ... debug: [bootz 0x82000000 0x88080000:587c90 88000000] ... ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Ramdisk to 8fa78000, end 8ffffc90 ... OK reserving fdt memory region: addr=88000000 size=7e000 Loading Device Tree to 8f9f7000, end 8fa77fff ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.105-ti-r114 (root@a5-imx6q-wandboard-2gb) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1) ) #1 SMP PREEMPT Fri Aug 17 11:05:53 UTC 2018 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt:Machine model: TI AM335x BeagleBone Black [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 48 MiB at 0x9c800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 15 pages/cpu @df902000 s31820 r8192 d21428 u61440 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 bone_capemgr.uboot_capemgr_enabled=1 root=/dev/mmcblk1p1 ro rootfstype=ext4 rootwait coherent_pool=1M net.ifnames=0 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 440224K/522240K available (12288K kernel code, 1139K rwdata, 4324K rodata, 1024K init, 459K bss, 32864K reserved, 49152K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0000000 - 0xff800000 ( 504 MB) [ 0.000000] lowmem : 0xc0000000 - 0xdfe00000 ( 510 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0d00000 (13280 kB) [ 0.000000] .init : 0xc1300000 - 0xc1400000 (1024 kB) [ 0.000000] .data : 0xc1400000 - 0xc151cd58 (1140 kB) [ 0.000000] .bss : 0xc151e000 - 0xc1590ff0 ( 460 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000023] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000052] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000066] OMAP clocksource: timer1 at 24000000 Hz [ 0.002104] clocksource_probe: no matching clocksources found [ 0.002431] Console: colour dummy device 80x30 [ 0.002466] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' [ 0.002475] This ensures that you still see kernel messages. Please [ 0.002483] update your kernel commandline. [ 0.002510] Calibrating delay loop... 995.32 BogoMIPS (lpj=1990656) [ 0.020720] pid_max: default: 32768 minimum: 301 [ 0.020989] Security Framework initialized [ 0.021005] Yama: becoming mindful. [ 0.021061] AppArmor: AppArmor initialized [ 0.021148] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.021161] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.022341] CPU: Testing write buffer coherency: ok [ 0.022416] ftrace: allocating 39262 entries in 116 pages [ 0.133505] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.133586] Setting up static identity map for 0x80100000 - 0x80100060 [ 0.167776] EFI services will not be available. [ 0.180714] Brought up 1 CPUs [ 0.180734] SMP: Total of 1 processors activated (995.32 BogoMIPS). [ 0.180744] CPU: All CPU(s) started in SVC mode. [ 0.182377] devtmpfs: initialized [ 0.221031] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.221614] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.221649] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.225369] xor: measuring software checksum speed [ 0.264735] arm4regs : 1217.000 MB/sec [ 0.304686] 8regs : 1091.000 MB/sec [ 0.344684] 32regs : 1088.000 MB/sec [ 0.384684] neon : 1665.000 MB/sec [ 0.384695] xor: using function: neon (1665.000 MB/sec) [ 0.384718] pinctrl core: initialized pinctrl subsystem [ 0.386220] NET: Registered protocol family 16 [ 0.390073] DMA: preallocated 1024 KiB pool for atomic coherent allocations [ 0.459132] omap_hwmod: debugss: _wait_target_disable failed [ 0.508732] cpuidle: using governor ladder [ 0.520712] cpuidle: using governor menu [ 0.537009] OMAP GPIO hardware version 0.1 [ 0.563832] No ATAGs? [ 0.563867] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.564801] omap4_sram_init:Unable to allocate sram needed to handle errata I688 [ 0.564825] omap4_sram_init:Unable to get sram pool needed to handle errata I688 [ 0.676740] raid6: neonx2 gen() 1882 MB/s [ 0.744710] raid6: neonx2 xor() 1157 MB/s [ 0.744722] raid6: using algorithm neonx2 gen() 1882 MB/s [ 0.744731] raid6: .... xor() 1157 MB/s, rmw enabled [ 0.744740] raid6: using intx1 recovery algorithm [ 0.755673] edma 49000000.edma: TI EDMA DMA engine driver [ 0.761887] SCSI subsystem initialized [ 0.762331] usbcore: registered new interface driver usbfs [ 0.762413] usbcore: registered new interface driver hub [ 0.762603] usbcore: registered new device driver usb [ 0.763736] omap_i2c 44e0b000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c0_pins, deferring probe [ 0.764825] omap_i2c 4802a000.i2c: bus 1 rev0.11 at 100 kHz [ 0.766308] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz [ 0.766592] media: Linux media interface: v0.10 [ 0.766660] Linux video capture interface: v2.00 [ 0.766754] pps_core: LinuxPPS API ver. 1 registered [ 0.766764] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]> [ 0.766790] PTP clock support registered [ 0.767942] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 [ 0.769092] Advanced Linux Sound Architecture Driver Initialized. [ 0.769920] NetLabel: Initializing [ 0.769937] NetLabel: domain hash size = 128 [ 0.769944] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.770019] NetLabel: unlabeled traffic allowed by default [ 0.773144] clocksource: Switched to clocksource timer1 [ 0.888801] VFS: Disk quotas dquot_6.6.0 [ 0.888935] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.889462] AppArmor: AppArmor Filesystem Enabled [ 0.905046] NET: Registered protocol family 2 [ 0.906114] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.906168] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.906229] TCP: Hash tables configured (established 4096 bind 4096) [ 0.906315] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.906338] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.906685] NET: Registered protocol family 1 [ 0.915593] RPC: Registered named UNIX socket transport module. [ 0.915612] RPC: Registered udp transport module. [ 0.915620] RPC: Registered tcp transport module. [ 0.915628] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.916568] Unpacking initramfs... [ 1.089204] random: fast init done [ 1.304334] Freeing initrd memory: 5664K [ 1.304953] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 1.308908] audit: initializing netlink subsys (disabled) [ 1.309022] audit: type=2000 audit(1.236:1): initialized [ 1.314681] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 1.324992] zbud: loaded [ 1.333516] NFS: Registering the id_resolver key type [ 1.333568] Key type id_resolver registered [ 1.333578] Key type id_legacy registered [ 1.333599] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.333976] fuse init (API version 7.26) [ 1.335144] orangefs_debugfs_init: called with debug mask: :none: :0: [ 1.335436] orangefs_init: module version upstream loaded [ 1.335449] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 1.350052] Key type asymmetric registered [ 1.350080] Asymmetric key parser 'x509' registered [ 1.350227] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 1.354558] io scheduler noop registered [ 1.354577] io scheduler deadline registered [ 1.354900] io scheduler cfq registered (default) [ 1.357936] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 1.364807] gpio-of-helper ocp:cape-universal: ready [ 1.377458] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc handle [ 1.379767] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled [ 1.383500] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 158, base_baud = 3000000) is a 8250 [ 2.221928] console [ttyS0] enabled [ 2.226481] 48022000.serial: ttyS1 at MMIO 0x48022000 (irq = 159, base_baud = 3000000) is a 8250 [ 2.236372] 48024000.serial: ttyS2 at MMIO 0x48024000 (irq = 160, base_baud = 3000000) is a 8250 [ 2.246218] 481a8000.serial: ttyS4 at MMIO 0x481a8000 (irq = 161, base_baud = 3000000) is a 8250 [ 2.258660] omap_rng 48310000.rng: OMAP Random Number Generator ver. 20 [ 2.265836] [drm] Initialized [ 2.272789] at24 2-0054: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 2.280141] at24 2-0055: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 2.287344] at24 2-0056: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 2.294510] at24 2-0057: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 2.323999] eqep 48300180.eqep: ver. 1.0 [ 2.328279] eqep 48300180.eqep: count_mode:0 [ 2.332630] eqep 48300180.eqep: invert_qa:1 [ 2.336864] eqep 48300180.eqep: invert_qb:1 [ 2.341092] eqep 48300180.eqep: invert_qi:0 [ 2.345320] eqep 48300180.eqep: invert_qs:0 [ 2.349547] eqep 48300180.eqep: swap_inputs:0 [ 2.353945] eqep 48300180.eqep: QDECCTL:0x0180 [ 2.358432] eqep 48300180.eqep: QPOSINIT:0x00000000 [ 2.363353] eqep 48300180.eqep: QPOSMAX:0xffffffff [ 2.368188] eqep 48300180.eqep: QPOSCNT:0x00000000 [ 2.373025] eqep 48300180.eqep: omit_interrupt:0 [ 2.377686] eqep 48300180.eqep: QEINT:0x0800 [ 2.381998] eqep 48300180.eqep: QUPRD:0x05f5e100 [ 2.386658] eqep 48300180.eqep: QEPCTL:0x009e write [ 2.391580] eqep 48300180.eqep: QEPCTL:0x009e read [ 2.396435] eqep 48300180.eqep: irq:193, clk_rate:100000000 [ 2.402385] eqep 48302180.eqep: ver. 1.0 [ 2.406541] eqep 48302180.eqep: count_mode:0 [ 2.410876] eqep 48302180.eqep: invert_qa:1 [ 2.415104] eqep 48302180.eqep: invert_qb:1 [ 2.419331] eqep 48302180.eqep: invert_qi:0 [ 2.423555] eqep 48302180.eqep: invert_qs:0 [ 2.427780] eqep 48302180.eqep: swap_inputs:0 [ 2.432179] eqep 48302180.eqep: QDECCTL:0x0180 [ 2.436665] eqep 48302180.eqep: QPOSINIT:0x00000000 [ 2.441588] eqep 48302180.eqep: QPOSMAX:0xffffffff [ 2.446421] eqep 48302180.eqep: QPOSCNT:0x00000000 [ 2.451257] eqep 48302180.eqep: omit_interrupt:0 [ 2.455917] eqep 48302180.eqep: QEINT:0x0800 [ 2.460228] eqep 48302180.eqep: QUPRD:0x05f5e100 [ 2.464896] eqep 48302180.eqep: QEPCTL:0x009e write [ 2.469819] eqep 48302180.eqep: QEPCTL:0x009e read [ 2.474669] eqep 48302180.eqep: irq:194, clk_rate:100000000 [ 2.480520] eqep 48304180.eqep: ver. 1.0 [ 2.484649] eqep 48304180.eqep: count_mode:0 [ 2.488988] eqep 48304180.eqep: invert_qa:1 [ 2.493220] eqep 48304180.eqep: invert_qb:1 [ 2.497446] eqep 48304180.eqep: invert_qi:0 [ 2.501670] eqep 48304180.eqep: invert_qs:0 [ 2.505894] eqep 48304180.eqep: swap_inputs:0 [ 2.510292] eqep 48304180.eqep: QDECCTL:0x0180 [ 2.514779] eqep 48304180.eqep: QPOSINIT:0x00000000 [ 2.519700] eqep 48304180.eqep: QPOSMAX:0xffffffff [ 2.524534] eqep 48304180.eqep: QPOSCNT:0x00000000 [ 2.529371] eqep 48304180.eqep: omit_interrupt:0 [ 2.534031] eqep 48304180.eqep: QEINT:0x0800 [ 2.538343] eqep 48304180.eqep: QUPRD:0x05f5e100 [ 2.543001] eqep 48304180.eqep: QEPCTL:0x009e write [ 2.547922] eqep 48304180.eqep: QEPCTL:0x009e read [ 2.552769] eqep 48304180.eqep: irq:196, clk_rate:100000000 [ 2.566819] libphy: Fixed MDIO Bus: probed [ 2.572180] CAN device driver interface [ 2.577874] c_can_platform 481cc000.can: c_can_platform device registered (regs=fa1cc000, irq=168) [ 2.588068] c_can_platform 481d0000.can: c_can_platform device registered (regs=fa1d0000, irq=169) [ 2.653253] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 2.659438] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 2.666602] davinci_mdio: dt: updated phy_id[0] from phy_mask[fffffffe] [ 2.687779] libphy: 4a101000.mdio: probed [ 2.692157] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 2.702570] cpsw 4a100000.ethernet: Detected MACID = 94:e3:6d:ce:1d:e3 [ 2.709460] cpsw 4a100000.ethernet: cpts: overflow check period 1250 (jiffies) [ 2.720998] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.727738] ehci-pci: EHCI PCI platform driver [ 2.732354] ehci-platform: EHCI generic platform driver [ 2.738138] ehci-omap: OMAP-EHCI Host Controller driver [ 2.744584] usbcore: registered new interface driver usb-storage [ 2.754062] 47401300.usb-phy supply vcc not found, using dummy regulator [ 2.767439] 47401b00.usb-phy supply vcc not found, using dummy regulator [ 2.778644] musb-hdrc musb-hdrc.1: MUSB HDRC host driver [ 2.784096] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 [ 2.791861] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.798726] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.806006] usb usb1: Product: MUSB HDRC host driver [ 2.811015] usb usb1: Manufacturer: Linux 4.9.105-ti-r114 musb-hcd [ 2.817247] usb usb1: SerialNumber: musb-hdrc.1 [ 2.822977] hub 1-0:1.0: USB hub found [ 2.826951] hub 1-0:1.0: 1 port detected [ 2.844902] omap_rtc 44e3e000.rtc: already running [ 2.850391] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ 2.859514] i2c /dev entries driver [ 2.866384] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 2.875228] cpuidle: enable-method property 'ti,am3352' found operations [ 2.884072] omap_hsmmc 48060000.mmc: Got CD GPIO [ 2.971662] ledtrig-cpu: registered to indicate activity on CPUs [ 2.982005] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 [ 2.988166] omap-aes 53500000.aes: will run requests pump with realtime priority [ 2.998550] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 [ 3.010840] hidraw: raw HID events driver (C) Jiri Kosina [ 3.017408] usbcore: registered new interface driver usbhid [ 3.023141] usbhid: USB HID core driver [ 3.027769] remoteproc remoteproc0: wkup_m3 is available [ 3.043772] wireguard: WireGuard 0.0.20180809 loaded. See www.wireguard.com for information. [ 3.052663] wireguard: Copyright (C) 2015-2018 Jason A. Donenfeld <[email protected]>. All Rights Reserved. [ 3.063825] NET: Registered protocol family 10 [ 3.069329] mmc1: new high speed MMC card at address 0001 [ 3.079772] mip6: Mobile IPv6 [ 3.083405] NET: Registered protocol family 17 [ 3.088008] mmcblk1: mmc1:0001 M62704 3.56 GiB [ 3.093228] can: controller area network core (rev 20120528 abi 9) [ 3.099528] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB [ 3.106150] NET: Registered protocol family 29 [ 3.110715] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB [ 3.118129] mmcblk1: p1 [ 3.123899] Key type dns_resolver registered [ 3.128290] mpls_gso: MPLS GSO support [ 3.132403] omap_voltage_late_init: Voltage driver support not added [ 3.139517] PM: Cannot get wkup_m3_ipc handle [ 3.144169] ThumbEE CPU extension supported. [ 3.148527] Registering SWP/SWPB emulation handler [ 3.154461] registered taskstats version 1 [ 3.158783] zswap: loaded using pool lzo/zbud [ 3.170224] Btrfs loaded, crc32c=crc32c-generic [ 3.209100] Key type encrypted registered [ 3.213566] AppArmor: AppArmor sha1 policy hashing enabled [ 3.237282] usb 1-1: new high-speed USB device number 2 using musb-hdrc [ 3.376033] tda998x 0-0070: found TDA19988 [ 3.381363] usb 1-1: New USB device found, idVendor=0409, idProduct=005a [ 3.388863] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_ops) [ 3.388880] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 3.388884] [drm] No driver support for vblank timestamp query. [ 3.395407] tilcdc 4830e000.lcdc: No connectors reported connected with modes [ 3.395426] [drm] Cannot find any crtc or sizes - going 1024x768 [ 3.429182] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 3.430378] hub 1-1:1.0: USB hub found [ 3.430474] hub 1-1:1.0: 4 ports detected [ 3.431693] Console: switching to colour frame buffer device 128x48 [ 3.459784] tilcdc 4830e000.lcdc: fb0: frame buffer device [ 3.492292] input: tps65217_pwr_but as /devices/platform/ocp/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 [ 3.503705] tps65217 0-0024: TPS65217 ID 0xe version 1.2 [ 3.509609] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 3.516662] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 3.523820] remoteproc remoteproc0: powering up wkup_m3 [ 3.532369] asoc-simple-card sound: hdmi-hifi.0 <-> 48038000.mcasp mapping ok [ 3.541413] PM: Cannot get wkup_m3_ipc handle [ 3.542697] omap_rtc 44e3e000.rtc: setting system clock to 2020-10-24 00:22:19 UTC (1603498939) [ 3.542708] of_cfs_init [ 3.542855] of_cfs_init: OK [ 3.543955] ALSA device list: [ 3.543964] #0: TI BeagleBone Black [ 3.572001] Freeing unused kernel memory: 1024K [ 3.576715] remoteproc remoteproc0: Booting fw image am335x-pm-firmware.elf, size 217168 [ 3.576984] remoteproc remoteproc0: remote processor wkup_m3 is now up [ 3.577005] wkup_m3_ipc 44e11324.wkup_m3_ipc: CM3 Firmware Version = 0x193 Loading, please wait... starting version 232 [ 3.686222] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 3.702314] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 3.711014] random: udevadm: uninitialized urandom read (16 bytes read) [ 3.725263] usb 1-1.1: new full-speed USB device number 3 using musb-hdrc [ 3.827645] usb 1-1.1: New USB device found, idVendor=046d, idProduct=c534 [ 3.841316] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.857337] usb 1-1.1: Product: USB Receiver [ 3.865407] usb 1-1.1: Manufacturer: Logitech [ 3.890281] input: Logitech USB Receiver as /devices/platform/ocp/47400000.usb/47401c00.usb/musb-hdrc.1/usb1/1-1/1-1.1/1-1.1:1.0/0003:046D:C534.0001/input/input1 [ 3.989439] hid-generic 0003:046D:C534.0001: input,hidraw0: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-musb-hdrc.1-1.1/input0 [ 4.020404] PM: bootloader does not support rtc-only! [ 4.037405] input: Logitech USB Receiver as /devices/platform/ocp/47400000.usb/47401c00.usb/musb-hdrc.1/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C534.0002/input/input2 [ 4.100396] hid-generic 0003:046D:C534.0002: input,hiddev0,hidraw1: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-musb-hdrc.1-1.1/input1 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems done. Begin: Will now check root file system ... fsck from util-linux 2.29.2 [/sbin/fsck.ext4 (1) -- /dev/mmcblk1p1] fsck.ext4 -a -C0 /dev/mmcblk1p1 rootfs: clean, 49969/233392 files, 414359/932864 blocks done. [ 13.337960] EXT4-fs (mmcblk1p1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 13.789991] ip_tables: (C) 2000-2006 Netfilter Core Team [ 13.830298] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [ 13.849487] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 9 (stretch)! [ 13.870759] systemd[1]: Set hostname to <G5-HMI>. [ 14.468576] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 14.486328] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 14.502400] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 14.526364] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 14.542373] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 14.558584] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on Journal Audit Socket. [ 14.575095] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ OK ] Created slice system-getty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. Mounting /sys/kernel/debug... [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on fsck to fsckd communication Socket. Mounting RPC Pipe File System... [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Encrypted Volumes. [ OK ] Reached target Paths. [ OK ] Listening on Syslog Socket. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target Swap. [ OK ] Reached target Slices. [ OK ] Set up automount Arbitrary Executab…rmats File System Automount Point. Mounting POSIX Message Queue File System... [ OK ] Listening on Journal Socket. Starting Load Kernel Modules... Starting Remount Root and Kernel File Systems... Starting Journal Service... Starting Create list of required st…ce nodes for the current kernel... [ 15.049440] EXT4-fs (mmcblk1p1): re-mounted. Opts: errors=remount-ro [ OK ] Mounted RPC Pipe File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted /sys/kernel/debug. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Create list of required sta…vice nodes for the current kernel. Starting Create Static Device Nodes in /dev... Starting udev Coldplug all Devices... Starting Load/Save Random Seed... Starting Apply Kernel Variables... Mounting Configuration File System... Mounting FUSE Control File System... [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Load/Save Random Seed. [ OK ] Started Apply Kernel Variables. [ OK ] Mounted Configuration File System. [ OK ] Mounted FUSE Control File System. Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Raise network interfaces... Starting Preprocess NFS configuration... [ OK ] Started Journal Service. Starting Flush Journal to Persistent Storage... [ OK ] Started Preprocess NFS configuration. [ OK ] Reached target NFS client services. [ OK ] Started udev Kernel Device Manager. [ 16.347168] systemd-journald[1404]: Received request to flush runtime journal from PID 1 [ OK ] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... Starting RPC bind portmap service... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started RPC bind portmap service. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. [ OK ] Reached target RPC Port Mapper. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Synchronized. [ OK ] Started udev Coldplug all Devices. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Started Daily apt download activities. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started Vision Series 5 Human Machine Interface. [ OK ] Started Regular background program processing daemon. Starting Login Service... Starting BB WL18xx wlan0 Service... [ OK ] Started D-Bus System Message Bus. Starting System Logging Service... [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Reached target Timers. Starting VS5 bootsplash... [ OK ] Started BB WL18xx wlan0 Service. [ OK ] Started System Logging Service. [ OK ] Started Login Service. [ OK ] Started VS5 bootsplash. [ 21.946082] random: crng init done [ 21.949534] random: 7 urandom warning(s) missed due to ratelimiting [ OK ] Reached target Sound Card. [ OK ] Found device /dev/ttyS0. [*** ] (1 of 2) A start job is running for…network interfaces (34s / 5min 1s)[ 49.638020] pvrsrvkm: loading out-of-tree module taints kernel. [** ] (2 of 2) A start job is running for dev-ttyGS0.device (35s / 1min 30s)[ 50.061998] [drm] Initialized pvr 1.14.3699939 20110701 on minor 1 [ **] (1 of 2) A start job is running for…network interfaces (40s / 5min 1s)[ 55.482071] net eth0: initializing cpsw version 1.12 (0) [ 55.493362] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 [ 55.509427] cpsw 4a100000.ethernet: ALE Table size 1024 [ ***] (1 of 2) A start job is running for…etwork interfaces (41s / 5min 40s)[ 55.598034] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=-1) [ 55.627984] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [*** ] (2 of 2) A start job is running for dev-ttyGS0.device (42s / 1min 30s)[ 57.638185] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 57.646399] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. Starting Permit User Sessions... Starting OpenBSD Secure Shell server... Starting Generic Board Startup... [ OK ] Started Permit User Sessions. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Getty on tty1. [ OK ] Started OpenBSD Secure Shell server. [ 64.008567] using random self ethernet address [ 64.016070] using random host ethernet address [ 64.076738] using random self ethernet address [ 64.084297] using random host ethernet address [ 64.267472] usb0: HOST MAC 94:e3:6d:ce:1d:e4 [ 64.277690] usb0: MAC 94:e3:6d:ce:1d:e5 [ 64.290638] usb1: HOST MAC 94:e3:6d:ce:1d:e7 [ 64.301474] usb1: MAC 94:e3:6d:ce:1d:e8 [ OK ] Found device /dev/ttyGS0. [ 64.645744] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready [ OK ] Started Serial Getty on ttyGS0. [ OK ] Reached target Login Prompts. [ 64.781848] IPv6: ADDRCONF(NETDEV_UP): usb1: link is not ready Starting dnsmasq - A lightweight DHCP and caching DNS server... [ OK ] Started dnsmasq - A lightweight DHCP and caching DNS server. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Started Generic Board Startup. Starting BB WL18xx Bluetooth Service... [ OK ] Started BB WL18xx Bluetooth Service. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Debian GNU/Linux 9 G5-HMI ttyS0 BeagleBoard.org Debian Image 2018-01-21 Vision Engraving Systems VS5 support 2019-06-20 G5-HMI login: Questions... Is not updating the bb-cape-overlays going to be an issue? What do you think the problem is? Is the bb-wl18xx-firmware needed? The BeagleBone Black does not have wireless (or is this bluetooth?) so I assume not but I want to make sure before removing it. What is the pvrsrvkm driver? It taints the kernel: [ 49.638020] pvrsrvkm: loading out-of-tree module taints kernel. Are these two packages needed? firmware-realtek firmware-ti-connectivity What are these two packages for? ti-sgx-ti335x-modules-4.9.105-ti-r1 tiomapconf I have my image pretty stripped down but have never been sure about the 4 above. Thanks for your help. Hartley -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/e07cd116-4d2a-4730-9078-6f4b2f228631o%40googlegroups.com.
