Hi,
Recently I got a seeedStudio senseCap LoRa gateway to try out for a LoRa
project we have coming up. Upon requesting if we could get root access to
the OS we were told that it was not been provided at this time. So I went
to explore mode and found that we could connect to the console and it
Identified itself as a beaglebone green (but could not get access with
default passwords).
So after reading some documents and the beagleboard.org website I worked
out I could boot from a uSD and get console and ssh access with the default
password.
But it doesn’t look like it able to start the ethernet interface and was
wondering if anyone here can help debug to why it wont start/enable.
Thanks
Some commands:
uname -a:
Linux beaglebone 4.19.94-ti-r42 #1buster SMP PREEMPT Tue Mar 31 19:38:29
UTC 2020 armv7l GNU/Linux
lscpu:
Architecture: armv7l
Byte Order: Little Endian
CPU(s): 1
On-line CPU(s) list: 0
Thread(s) per core: 1
Core(s) per socket: 1
Socket(s): 1
Vendor ID: ARM
Model: 2
Model name: Cortex-A8
Stepping: r3p2
CPU max MHz: 1000.0000
CPU min MHz: 300.0000
BogoMIPS: 995.32
Flags: half thumb fastmult vfp edsp thumbee neon vfpv3 tls
vfpd32
lsmod:
Module Size Used by
usb_f_acm 16384 2
u_serial 20480 3 usb_f_acm
usb_f_ecm 20480 2
usb_f_mass_storage 53248 2
usb_f_rndis 32768 4
u_ether 20480 2 usb_f_ecm,usb_f_rndis
libcomposite 65536 18
usb_f_ecm,usb_f_acm,usb_f_mass_storage,usb_f_rndis
pm33xx 16384 0
wkup_m3_ipc 16384 1 pm33xx
wkup_m3_rproc 16384 1
uio_pdrv_genirq 16384 0
uio 20480 1 uio_pdrv_genirq
ifconfig -a:
can0: flags=128<NOARP> mtu 16
unspec 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 txqueuelen
10 (UNSPEC)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 43
can1: flags=128<NOARP> mtu 16
unspec 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 txqueuelen
10 (UNSPEC)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 44
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 3976 bytes 253924 (247.9 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 3976 bytes 253924 (247.9 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
usb0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.7.2 netmask 255.255.255.0 broadcast 192.168.7.255
inet6 fe80::1642:fcff:fee7:1795 prefixlen 64 scopeid 0x20<link>
ether 14:42:fc:e7:17:95 txqueuelen 1000 (Ethernet)
RX packets 7736 bytes 1788640 (1.7 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 647 bytes 124298 (121.3 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
usb1: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 192.168.6.2 netmask 255.255.255.0 broadcast 192.168.6.255
ether 14:42:fc:e7:17:99 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
dmesg:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.19.94-ti-r42
(voodoo@x3-am57xx-beagle-x15-2gb) (gcc version 8.3.0 (Debian 8.3.0-6))
#1buster SMP PREEMPT Tue Mar 31 19:38:29 UTC 2020
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7),
cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
instruction cache
[ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Green Wireless
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] cma: Reserved 48 MiB at 0x9c800000
[ 0.000000] On node 0 totalpages: 130560
[ 0.000000] Normal zone: 1148 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 130560 pages, LIFO batch:31
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] AM335X ES2.1 (sgx neon)
[ 0.000000] random: get_random_bytes called from start_kernel+0xac/0x4b4
with crng_init=0
[ 0.000000] percpu: Embedded 17 pages/cpu s38988 r8192 d22452 u69632
[ 0.000000] pcpu-alloc: s38988 r8192 d22452 u69632 alloc=17*4096
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412
[ 0.000000] Kernel command line: console=ttyO0,115200n8
bone_capemgr.uboot_capemgr_enabled=1 root=/dev/mmcblk1p1 ro rootfstype=ext4
rootwait coherent_pool=1M net.ifnames=0 lpj=1990656
rng_core.default_quality=100 quiet
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 0.000000] Memory: 438432K/522240K available (13312K kernel code, 1136K
rwdata, 4308K rodata, 1024K init, 350K bss, 34656K reserved, 49152K
cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xe0000000 - 0xff800000 ( 504 MB)
lowmem : 0xc0000000 - 0xdfe00000 ( 510 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0x(ptrval) - 0x(ptrval) (14304 kB)
.init : 0x(ptrval) - 0x(ptrval) (1024 kB)
.data : 0x(ptrval) - 0x(ptrval) (1137 kB)
.bss : 0x(ptrval) - 0x(ptrval) ( 351 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] ftrace: allocating 42043 entries in 124 pages
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128
interrupts
[ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz
[ 0.000024] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every
89478484971ns
[ 0.000044] clocksource: timer1: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 79635851949 ns
[ 0.000054] OMAP clocksource: timer1 at 24000000 Hz
[ 0.002078] timer_probe: no matching timers found
[ 0.002425] Console: colour dummy device 80x30
[ 0.002454] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0'
[ 0.002459] This ensures that you still see kernel messages. Please
[ 0.002463] update your kernel commandline.
[ 0.002524] Calibrating delay loop (skipped) preset value.. 995.32
BogoMIPS (lpj=1990656)
[ 0.002541] pid_max: default: 32768 minimum: 301
[ 0.002827] Security Framework initialized
[ 0.002841] Yama: becoming mindful.
[ 0.002987] AppArmor: AppArmor initialized
[ 0.003092] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.003105] Mountpoint-cache hash table entries: 1024 (order: 0, 4096
bytes)
[ 0.004204] CPU: Testing write buffer coherency: ok
[ 0.004269] CPU0: Spectre v2: using BPIALL workaround
[ 0.004763] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[ 0.025231] Setting up static identity map for 0x80100000 - 0x80100060
[ 0.033137] rcu: Hierarchical SRCU implementation.
[ 0.049155] smp: Bringing up secondary CPUs ...
[ 0.049174] smp: Brought up 1 node, 1 CPU
[ 0.049186] SMP: Total of 1 processors activated (995.32 BogoMIPS).
[ 0.049192] CPU: All CPU(s) started in SVC mode.
[ 0.050912] devtmpfs: initialized
[ 0.085490] VFP support v0.3: implementor 41 architecture 3 part 30
variant c rev 3
[ 0.086122] clocksource: jiffies: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.086147] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.090117] xor: automatically using best checksumming function neon
[ 0.090134] pinctrl core: initialized pinctrl subsystem
[ 0.091464] NET: Registered protocol family 16
[ 0.096703] DMA: preallocated 1024 KiB pool for atomic coherent
allocations
[ 0.188888] l4_wkup_cm:clk:0010:0: failed to disable
[ 0.229251] audit: initializing netlink subsys (disabled)
[ 0.233252] audit: type=2000 audit(0.224:1): state=initialized
audit_enabled=0 res=1
[ 0.238296] OMAP GPIO hardware version 0.1
[ 0.239153] GPIO line 61 (LS_BUF_EN) hogged as output/high
[ 0.241409] GPIO line 112 (MCASP0_AHCLKR) hogged as output/low
[ 0.262954] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.289291] raid6: using algorithm neonx8 gen() 0 MB/s
[ 0.289304] raid6: .... xor() 0 MB/s, rmw enabled
[ 0.289312] raid6: using neon recovery algorithm
[ 0.297400] edma 49000000.edma: TI EDMA DMA engine driver
[ 0.304834] SCSI subsystem initialized
[ 0.309250] libata version 3.00 loaded.
[ 0.309558] usbcore: registered new interface driver usbfs
[ 0.309614] usbcore: registered new interface driver hub
[ 0.309735] usbcore: registered new device driver usb
[ 0.311810] omap_i2c 4802a000.i2c: bus 1 rev0.11 at 100 kHz
[ 0.313358] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz
[ 0.313966] pps_core: LinuxPPS API ver. 1 registered
[ 0.313975] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo
Giometti <[email protected]>
[ 0.314000] PTP clock support registered
[ 0.314886] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400
[ 0.317537] Advanced Linux Sound Architecture Driver Initialized.
[ 0.318396] NetLabel: Initializing
[ 0.318406] NetLabel: domain hash size = 128
[ 0.318411] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 0.318500] NetLabel: unlabeled traffic allowed by default
[ 0.319571] clocksource: Switched to clocksource timer1
[ 0.481934] VFS: Disk quotas dquot_6.6.0
[ 0.482039] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096
bytes)
[ 0.482919] AppArmor: AppArmor Filesystem Enabled
[ 0.495940] NET: Registered protocol family 2
[ 0.496941] tcp_listen_portaddr_hash hash table entries: 512 (order: 0,
6144 bytes)
[ 0.496974] TCP established hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.497016] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.497074] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.497207] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.497229] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.497568] NET: Registered protocol family 1
[ 0.510748] RPC: Registered named UNIX socket transport module.
[ 0.510759] RPC: Registered udp transport module.
[ 0.510765] RPC: Registered tcp transport module.
[ 0.510770] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.511828] Unpacking initramfs...
[ 0.879070] Freeing initrd memory: 6436K
[ 0.879992] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5
counters available
[ 0.883134] Initialise system trusted keyrings
[ 0.883656] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.890650] zbud: loaded
[ 0.898090] NFS: Registering the id_resolver key type
[ 0.898134] Key type id_resolver registered
[ 0.898141] Key type id_legacy registered
[ 0.898159] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.898507] fuse init (API version 7.27)
[ 0.909136] Key type asymmetric registered
[ 0.909152] Asymmetric key parser 'x509' registered
[ 0.909267] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 246)
[ 0.913652] io scheduler noop registered
[ 0.913663] io scheduler deadline registered
[ 0.913980] io scheduler cfq registered (default)
[ 0.913990] io scheduler mq-deadline registered
[ 0.917863] pinctrl-single 44e10800.pinmux: 142 pins, size 568
[ 0.930301] gpio-of-helper ocp:cape-universal: ready
[ 0.943789] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[ 0.947333] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 30,
base_baud = 3000000) is a 8250
[ 0.957468] console [ttyS0] enabled
[ 0.958625] 48022000.serial: ttyS1 at MMIO 0x48022000 (irq = 31,
base_baud = 3000000) is a 8250
[ 0.959745] 48024000.serial: ttyS2 at MMIO 0x48024000 (irq = 32,
base_baud = 3000000) is a 8250
[ 0.960820] 481a6000.serial: ttyS3 at MMIO 0x481a6000 (irq = 33,
base_baud = 3000000) is a 8250
[ 0.961786] 481a8000.serial: ttyS4 at MMIO 0x481a8000 (irq = 34,
base_baud = 3000000) is a 8250
[ 0.962709] 481aa000.serial: ttyS5 at MMIO 0x481aa000 (irq = 35,
base_baud = 3000000) is a 8250
[ 0.966430] omap_rng 48310000.rng: Random Number Generator ver. 20
[ 0.967435] sdhci: Secure Digital Host Controller Interface driver
[ 0.967444] sdhci: Copyright(c) Pierre Ossman
[ 0.968203] omap_gpio 44e07000.gpio: Could not set line 6 debounce to
200000 microseconds (-22)
[ 0.968215] omap_hsmmc 48060000.mmc: Got CD GPIO
[ 0.968803] omap_hsmmc 48060000.mmc: Linked as a consumer to regulator.2
[ 0.969154] random: fast init done
[ 0.969528] random: crng init done
[ 0.995957] omap_hsmmc 481d8000.mmc: Linked as a consumer to regulator.2
[ 1.022578] omap_hsmmc 47810000.mmc: Linked as a consumer to regulator.1
[ 1.065232] mmc1: new high speed MMC card at address 0001
[ 1.070625] mmcblk1: mmc1:0001 Q2J55L 7.09 GiB
[ 1.071250] mmcblk1boot0: mmc1:0001 Q2J55L partition 1 16.0 MiB
[ 1.071969] mmcblk1boot1: mmc1:0001 Q2J55L partition 2 16.0 MiB
[ 1.072317] mmcblk1rpmb: mmc1:0001 Q2J55L partition 3 4.00 MiB, chardev
(245:0)
[ 1.078357] mmcblk1: p1
[ 1.124219] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.247541] eqep 48300180.eqep: ver. 1.0
[ 1.247864] eqep 48300180.eqep: count_mode:0
[ 1.247875] eqep 48300180.eqep: invert_qa:1
[ 1.247883] eqep 48300180.eqep: invert_qb:1
[ 1.247891] eqep 48300180.eqep: invert_qi:0
[ 1.247899] eqep 48300180.eqep: invert_qs:0
[ 1.247908] eqep 48300180.eqep: swap_inputs:0
[ 1.247917] eqep 48300180.eqep: QDECCTL:0x0180
[ 1.247925] eqep 48300180.eqep: QPOSINIT:0x00000000
[ 1.247932] eqep 48300180.eqep: QPOSMAX:0xffffffff
[ 1.247939] eqep 48300180.eqep: QPOSCNT:0x00000000
[ 1.247947] eqep 48300180.eqep: omit_interrupt:0
[ 1.247954] eqep 48300180.eqep: QEINT:0x0800
[ 1.247962] eqep 48300180.eqep: QUPRD:0x05f5e100
[ 1.247969] eqep 48300180.eqep: QEPCTL:0x009e write
[ 1.247976] eqep 48300180.eqep: QEPCTL:0x009e read
[ 1.248001] eqep 48300180.eqep: irq:128, clk_rate:100000000
[ 1.248330] eqep 48302180.eqep: ver. 1.0
[ 1.248478] eqep 48302180.eqep: count_mode:0
[ 1.248488] eqep 48302180.eqep: invert_qa:1
[ 1.248496] eqep 48302180.eqep: invert_qb:1
[ 1.248504] eqep 48302180.eqep: invert_qi:0
[ 1.248512] eqep 48302180.eqep: invert_qs:0
[ 1.248520] eqep 48302180.eqep: swap_inputs:0
[ 1.248528] eqep 48302180.eqep: QDECCTL:0x0180
[ 1.248535] eqep 48302180.eqep: QPOSINIT:0x00000000
[ 1.248542] eqep 48302180.eqep: QPOSMAX:0xffffffff
[ 1.248549] eqep 48302180.eqep: QPOSCNT:0x00000000
[ 1.248557] eqep 48302180.eqep: omit_interrupt:0
[ 1.248563] eqep 48302180.eqep: QEINT:0x0800
[ 1.248570] eqep 48302180.eqep: QUPRD:0x05f5e100
[ 1.248577] eqep 48302180.eqep: QEPCTL:0x009e write
[ 1.248585] eqep 48302180.eqep: QEPCTL:0x009e read
[ 1.248604] eqep 48302180.eqep: irq:130, clk_rate:100000000
[ 1.248811] eqep 48304180.eqep: ver. 1.0
[ 1.248935] eqep 48304180.eqep: count_mode:0
[ 1.248944] eqep 48304180.eqep: invert_qa:1
[ 1.248952] eqep 48304180.eqep: invert_qb:1
[ 1.248960] eqep 48304180.eqep: invert_qi:0
[ 1.248968] eqep 48304180.eqep: invert_qs:0
[ 1.248975] eqep 48304180.eqep: swap_inputs:0
[ 1.248982] eqep 48304180.eqep: QDECCTL:0x0180
[ 1.248990] eqep 48304180.eqep: QPOSINIT:0x00000000
[ 1.248997] eqep 48304180.eqep: QPOSMAX:0xffffffff
[ 1.249004] eqep 48304180.eqep: QPOSCNT:0x00000000
[ 1.249011] eqep 48304180.eqep: omit_interrupt:0
[ 1.249018] eqep 48304180.eqep: QEINT:0x0800
[ 1.249025] eqep 48304180.eqep: QUPRD:0x05f5e100
[ 1.249032] eqep 48304180.eqep: QEPCTL:0x009e write
[ 1.249039] eqep 48304180.eqep: QEPCTL:0x009e read
[ 1.249059] eqep 48304180.eqep: irq:132, clk_rate:100000000
[ 1.321077] libphy: Fixed MDIO Bus: probed
[ 1.322047] CAN device driver interface
[ 1.323524] c_can_platform 481cc000.can: c_can_platform device
registered (regs=1cba9db5, irq=43)
[ 1.324909] c_can_platform 481d0000.can: c_can_platform device
registered (regs=caa84175, irq=44)
[ 1.326913] usbcore: registered new interface driver smsc95xx
[ 1.328757] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.328823] ehci-platform: EHCI generic platform driver
[ 1.329209] ehci-omap: OMAP-EHCI Host Controller driver
[ 1.330205] usbcore: registered new interface driver usb-storage
[ 1.333745] am335x-phy-driver 47401300.usb-phy: 47401300.usb-phy supply
vcc not found, using dummy regulator
[ 1.333909] am335x-phy-driver 47401300.usb-phy: Linked as a consumer to
regulator.0
[ 1.337427] am335x-phy-driver 47401b00.usb-phy: 47401b00.usb-phy supply
vcc not found, using dummy regulator
[ 1.337631] am335x-phy-driver 47401b00.usb-phy: Linked as a consumer to
regulator.0
[ 1.341150] musb-hdrc musb-hdrc.1: MUSB HDRC host driver
[ 1.341188] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus
number 1
[ 1.341541] usb usb1: New USB device found, idVendor=1d6b,
idProduct=0002, bcdDevice= 4.19
[ 1.341551] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.341559] usb usb1: Product: MUSB HDRC host driver
[ 1.341566] usb usb1: Manufacturer: Linux 4.19.94-ti-r42 musb-hcd
[ 1.341573] usb usb1: SerialNumber: musb-hdrc.1
[ 1.342393] hub 1-0:1.0: USB hub found
[ 1.342457] hub 1-0:1.0: 1 port detected
[ 1.355074] omap_rtc 44e3e000.rtc: registered as rtc0
[ 1.356921] i2c /dev entries driver
[ 1.361132] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60
sec
[ 1.361765] softdog: initialized. soft_noboot=0 soft_margin=60 sec
soft_panic=0 (nowayout=0)
[ 1.366483] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.367061] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
[ 1.367411] omap-aes 53500000.aes: will run requests pump with realtime
priority
[ 1.370250] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
[ 1.374299] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.382282] gnss: GNSS driver registered with major 242
[ 1.389558] NET: Registered protocol family 10
[ 1.460964] Segment Routing with IPv6
[ 1.461104] mip6: Mobile IPv6
[ 1.461277] NET: Registered protocol family 17
[ 1.461308] can: controller area network core (rev 20170425 abi 9)
[ 1.461396] NET: Registered protocol family 29
[ 1.461500] 8021q: 802.1Q VLAN Support v1.8
[ 1.461594] Key type dns_resolver registered
[ 1.461600] mpls_gso: MPLS GSO support
[ 1.461907] ThumbEE CPU extension supported.
[ 1.461922] Registering SWP/SWPB emulation handler
[ 1.461933] omap_voltage_late_init: Voltage driver support not added
[ 1.470149] registered taskstats version 1
[ 1.470160] Loading compiled-in X.509 certificates
[ 1.470291] zswap: loaded using pool lzo/zbud
[ 1.473717] Btrfs loaded, crc32c=crc32c-generic
[ 1.473834] AppArmor: AppArmor sha1 policy hashing enabled
[ 1.529559] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set
[ 1.530395] input: tps65217_pwr_but as
/devices/platform/ocp/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0
[ 1.531387] tps65217 0-0024: TPS65217 ID 0xe version 1.2
[ 1.532465] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1
bytes/write
[ 1.532576] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz
[ 1.537275] cpu cpu0: Linked as a consumer to regulator.4
[ 1.537386] cpu cpu0: Dropping the link to regulator.4
[ 1.537899] cpu cpu0: Linked as a consumer to regulator.4
[ 1.540229] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01
00:00:00 UTC (946684800)
[ 1.541687] ALSA device list:
[ 1.541696] No soundcards found.
[ 1.548100] Freeing unused kernel memory: 1024K
[ 1.548830] Run /init as init process
[ 1.751730] usb 1-1: new high-speed USB device number 2 using musb-hdrc
[ 1.899985] usb 1-1: New USB device found, idVendor=0424,
idProduct=2514, bcdDevice= b.b3
[ 1.900003] usb 1-1: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 1.901407] hub 1-1:1.0: USB hub found
[ 1.901595] hub 1-1:1.0: 4 ports detected
[ 8.163274] EXT4-fs (mmcblk1p1): INFO: recovery required on readonly
filesystem
[ 8.163289] EXT4-fs (mmcblk1p1): write access will be enabled during
recovery
[ 8.960463] EXT4-fs (mmcblk1p1): recovery complete
[ 8.964815] EXT4-fs (mmcblk1p1): mounted filesystem with ordered data
mode. Opts: (null)
[ 9.520924] systemd[1]: System time before build time, advancing clock.
[ 9.562259] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT
+SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT
+GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2
default-hierarchy=hybrid)
[ 9.563080] systemd[1]: Detected architecture arm.
[ 9.581523] systemd[1]: Set hostname to <beaglebone>.
[ 10.851330] systemd[1]:
/lib/systemd/system/rc_battery_monitor.service:5: PIDFile= references path
below legacy directory /var/run/, updating /var/run/rc_battery_monitor.pid
→ /run/rc_battery_monitor.pid; please update the unit file accordingly.
[ 10.992057] systemd[1]: Listening on Journal Audit Socket.
[ 10.993039] systemd[1]: Started Forward Password Requests to Wall
Directory Watch.
[ 11.000557] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 11.002618] systemd[1]: Set up automount Arbitrary Executable File
Formats File System Automount Point.
[ 11.002831] systemd[1]: Reached target Swap.
[ 11.004541] systemd[1]: Listening on Journal Socket.
[ 11.694079] remoteproc remoteproc0: 4a334000.pru is available
[ 11.694262] pru-rproc 4a334000.pru: PRU rproc node pru@4a334000 probed
successfully
[ 11.710576] remoteproc remoteproc1: 4a338000.pru is available
[ 11.710760] pru-rproc 4a338000.pru: PRU rproc node pru@4a338000 probed
successfully
[ 12.571909] EXT4-fs (mmcblk1p1): re-mounted. Opts: errors=remount-ro
[ 13.336651] systemd-journald[761]: Received request to flush runtime
journal from PID 1
[ 31.719697] wlan-en-regulator: disabling
[ 56.065310] remoteproc remoteproc2: wkup_m3 is available
[ 56.418332] remoteproc remoteproc2: powering up wkup_m3
[ 56.418365] remoteproc remoteproc2: Booting fw image
am335x-pm-firmware.elf, size 217168
[ 56.418650] remoteproc remoteproc2: remote processor wkup_m3 is now up
[ 56.418683] wkup_m3_ipc 44e11324.wkup_m3_ipc: CM3 Firmware Version =
0x193
[ 56.497334] PM: bootloader does not support rtc-only!
[ 60.447288] using random self ethernet address
[ 60.447307] using random host ethernet address
[ 60.548830] Mass Storage Function, version: 2009/09/11
[ 60.548855] LUN: removable file: (no medium)
[ 60.646576] using random self ethernet address
[ 60.646594] using random host ethernet address
[ 60.744166] usb0: HOST MAC 14:42:fc:e7:17:96
[ 60.746993] usb0: MAC 14:42:fc:e7:17:95
[ 60.755353] usb1: HOST MAC 14:42:fc:e7:17:98
[ 60.756580] usb1: MAC 14:42:fc:e7:17:99
[ 60.973288] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready
[ 61.029479] configfs-gadget gadget: high-speed config #1: c
[ 61.029840] IPv6: ADDRCONF(NETDEV_CHANGE): usb0: link becomes ready
[ 61.126665] IPv6: ADDRCONF(NETDEV_UP): usb1: link is not ready
--
For more options, visit http://beagleboard.org/discuss
---
You received this message because you are subscribed to the Google Groups
"BeagleBoard" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/beagleboard/b67ce9a6-7c9a-41d6-81c7-c0835663a47en%40googlegroups.com.
