-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 On 18.2.2015 10:48, Arnaud Fenioux wrote: > Hi all, > > I was notified there was a change in 1.4.0 : > >> This is a change in default value of 'table' for 'show route' >> command, now it is inferred from the protocol or export options >> (when used). To restore the old behavior just add 'table >> master' to 'show route' when no table is specified. > > And I see this is explained, after reading more carefully the > documentation http://bird.network.cz/?get_doc&f=bird-4.html : > "show route” : Show contents of a routing table (by default of > the main one or the table attached to a respective protocol), > that is routes, their metrics and (in case the all switch is > given) all their attributes. > > May I suggest to update the documentation on gitlab ? > https://gitlab.labs.nic.cz/labs/bird/wikis/Route_server_with_community_based_filtering_and_multiple_RIBs
Fixed. > Ondrej. > > > Arnaud > >> On 17 Feb 2015, at 16:35, Arnaud Fenioux >> <[email protected]> wrote: >> >> Hello, >> >> I’m running BIRD 1.4.5 on an IXP with this setup : "Route >> server with community based filtering and multiple RIBs" >> https://gitlab.labs.nic.cz/labs/bird/wikis/Route_server_with_community_based_filtering_and_multiple_RIBs >> >> >> I have noticed a strange behaviour of the "show route" command whenever I specify “table master” or not. >> (IP/AS have been anonymised in order to follow the example >> above) : >> >> root@rs2-th2:~# birdc "show route all 12.34.0.0/16 protocol >> R111x1" BIRD 1.4.5 ready. 12.34.0.0/16 via 10.0.0.11 on eth1 >> [R111x1 2015-02-16 10:43:59] * (100) [AS111i] Type: BGP unicast >> univ BGP.origin: IGP BGP.as_path: 111 BGP.next_hop: 10.0.0.11 >> BGP.med: 0 BGP.local_pref: 100 BGP.community: (0,51706) >> >> root@rs2-th2:~# birdc "show route table master all 12.34.0.0/16 >> protocol R111x1" BIRD 1.4.5 ready. 12.34.0.0/16 via >> 10.0.0.11 on eth1 [R111x1 2015-02-17 11:05:45] * (100) >> [AS111i] Type: BGP unicast univ BGP.origin: IGP BGP.as_path: >> 111 BGP.next_hop: 10.0.0.11 BGP.med: 0 BGP.local_pref: 100 >> BGP.community: (51706,64650) (51706,64602) (0,51706) >> >> When explicitly specifying “table master” I see communities >> added from filter “bgp_in_AS111”. When not specifying any table >> I see route from T111 (the table declared in "protocol bgp >> R111x1"). >> >> Actually I was expecting to have same output on both commands, >> as it explained in documentation : "If you want to see routes >> that where accepted from this router to the master routing >> table then type: bird> show route protocol R222x1" >> >> Does any body also noticed this behaviour? >> >> Regards, >> >> -- Arnaud Fenioux Network Engineer - FranceIX >> >> > -----BEGIN PGP SIGNATURE----- Version: GnuPG v1 iQIcBAEBAgAGBQJU5GGNAAoJED82D4RIDoWP63oP+gJK1wp6E17gSF+kwhyfQsJp 85N9eCkitJ8MI1BGRRaeksjjg5hs1K7qdx83r8h1bM+2kc4CckgnushHwaQfl8vP RyyjfZuIQxn5i7B2ZR1rAsfd4oCwysZerkwRsiEfjqBlD9CfnxpLXmVlq73s3zUe LzEDECNn7ceUSS6aHXwi0lQdciOuMASCpNV6QtTlxcQkc7Ly8O5sjOsu21QPmK0L s8DVn/M8FsNHo8lu4GKxhtuGVBOcTBJkuVZC6ngG+hRlBBUm5gerXEkYK1A+9BLr rP4GSFOqlaVRqIwQcACWLslFIn1PpI6kHXgGkOKnWOWGu9nrgNQTaREqaLjz1bta j3MXPii39P49Kn9/UtWwtwQGWQgYs/NbJJ7ZJabEZAcUCcqpp6tGnOzO7YnopcA8 k4mN+b3BfHKbTVDLCEx6I0DVSuqGVdbc9pH47y2vMlrlwB+BYqDQ+1D4qWdpDmLb HQxEW4vSWTJFT0MZJ2delgjluXjpYcFxr3nly78w9OGo4tWCcdzJmqBX+gtxBs5M 0ZXz7pDdH0jzLVSvTkW0fyF9+qQIq8DLkFjRQQyxp+eueA+Z8cFBYQNh29so9UuW bznXz0GeDWq2DgDiVf4dbGqqS1ukMpHVAXDt716u7Xc8Cd883q5HLMQ86jIj0rj4 gGhzaCuerMAu7BpbHPD4 =5uws -----END PGP SIGNATURE-----
