On Wed, 2018-04-25 at 11:12 +0100, Stuart wrote:
> On 25/04/18 02:31, Wayne Blaszczyk wrote:
> > On Tue, 2018-04-24 at 09:49 +0100, Stuart wrote:
> > > On 23/04/18 22:44, Wayne Blaszczyk wrote:
> > > > sh ../hplip-3.18.3-plugin.run --target . --noexec --nox11
> > > > install -d /usr/share/hplip/data/firmware
> > > > install -d /usr/share/hplip/fax/plugins
> > > > install -d /usr/share/hplip/prnt/plugins
> > > > install -d /usr/share/hplip/scan/plugins
> > > > install -d /usr/share/licenses/hplip-plugin
> > > > install -d /var/lib/hp
> > > > install -m644 plugin.spec /usr/share/hplip/
> > > > install -m644 hp_laserjet_*.fw.gz /usr/share/hplip/data/firmware/
> > > > install -m755 fax_marvell-x86_64.so /usr/share/hplip/fax/plugins/
> > > > install -m755 hbpl1-x86_64.so /usr/share/hplip/prnt/plugins/
> > > > install -m755 lj-x86_64.so /usr/share/hplip/prnt/plugins/
> > > > install -m755 bb_*-x86_64.so /usr/share/hplip/scan/plugins/
> > > > cat > /var/lib/hp/hplip.state << "EOF"
> > > > [plugin]
> > > > installed = 1
> > > > eula = 1
> > > > version = 3.18.3
> > > > EOF
> > > > find /usr/share/hplip -type f -name "*.so" | while read f; do
> > > > lib_dir="${f%/*}"
> > > > lib_name="${f##*/}"
> > > > ln -vsf "$lib_name" "$lib_dir/${lib_name%%-*}.so"
> > > > done
> > >
> > > Hi Bruce,Wayne,
> > > Rebuilt as suggested but still getting report of filter failure.
> > > The attached cups log was produced with debug2 but I cannot see anything
> > > obvious.
> > > Thanks
> > >
> >
> > So does hp-testpage produce the same result?
> > What do the following commands produce?
> > hp-check
> > hp-info
> > hp-doctor
> >
> >
> >
> >
> >
>
> hp-check reported some issues with "sane" so I installed sane and dependences
> and cleared most of the issues, cups printing remains the same but
> hp-testpage works !
> hp-check reports it cannot find libsane.so.
>
> but
> ls -tlr /usr/lib/libsane*.so*
> -rwxr-xr-x 1 root root 223504 Apr 25 09:33 libsane.so.1.0.27
> lrwxrwxrwx 1 root root 17 Apr 25 09:33 libsane.so.1 -> libsane.so.1.0.27
> lrwxrwxrwx 1 root root 17 Apr 25 09:33 libsane.so -> libsane.so.1.0.27
>
I'm not sure what is going on here, maybe you need to rebuild/re-install hplip?
> hp-check.log attached.
>
> I have removed all the printers from cups except the HP7760 on the usb port
> to simplify testing. I had to change permission on the /etc/cups directory to
> allow access using the hp tools from non
> root users.
>
All you need to do here was to add yourself to the lp group.
>
>
You didn't confirm how you installed your printers in the first place, via cups
or hp-setup?
If the former, then remove all printers from cups, then add a printer using
hp-setup.
Then try hp-testpage again, then print a test page from cups.
If that doesn't work, then I'm out of ideas other than have a look at the
following link.
https://wiki.archlinux.org/index.php/CUPS/Troubleshooting (section 5)
and perhaps installing foomatic-db* packages?
Regards,
Wayne.
--
http://lists.linuxfromscratch.org/listinfo/blfs-support
FAQ: http://www.linuxfromscratch.org/blfs/faq.html
Unsubscribe: See the above information page
