did you hear the ding? did you put the aircraft nose up to 12 to 15
degrees with down arrow before taking off? once at take off speed did
you quickly put up landing gear and flaps?
On 7/8/2017 9:25 PM, Austin Pinto wrote:
hi.
i did all i could.
ear a1 on left ear turned left west with ctrl left arrow.
crashed.
i also tried turning left when it eared it the most loudest still crashed.
so out of ideas on this1.
i think ill need a audio demo on takeoff and landing on big airports.
can some1 help?
On 7/8/17, Josh Kennedy <[email protected]> wrote:
if it says runway is full just circle the airport hitting f1 every now
and then to try and get clearance to land.
On 7/8/2017 2:23 AM, Austin Pinto wrote:
hi. i have made some if not lot of progress with your help.
now i have 3 more questions and then i should be able to figure the
game out on my own i think.
first when we contact atc for landing clearence sometimes they say
airport closed technical problem.
what do we do then.
some times they say runways full please standby.
so how can we stop moving ahead. if we keep flying we will cross the
airport.
also they say takeoff from runway a1 or b1 and how do we know whare is
the runway
On 7/8/17, Josh Kennedy <[email protected]> wrote:
minus 800 means you are not at the parking position yet. it will say
minus 800
minus 600
minus 449
minus 300
minus 221
minus 210
minus 140
minus 80
minus 10
minus 1
zero
then when you are at between 0 and one hundred then stop the plane and
you have successfully parked.
On 7/7/2017 1:35 AM, Austin Pinto wrote:
after landing successful if i press k i get -800 what is that?
On 7/7/17, Josh Kennedy <[email protected]> wrote:
turn on brakes, open door, get passengers off with control w. make
sure
you park between latitude 0 and 100.
On 7/6/2017 9:31 PM, Austin Pinto wrote:
yea! landing successfull on my first mission.
but what do i do after landing.
how to park just reduce speed to 0 and cutoff the engine?
i tried that but the first mission still contenues.
On 7/6/17, Austin Pinto <[email protected]> wrote:
ok. got that.
also i wanted to ask when doing free fly and i get takeoff cleared
from runway a1 or b1.
how do i know whare i am standing and whare is a1 or b1
On 7/6/17, Nail Alimzhanov <[email protected]> wrote:
Hi Austin. Lets go step by step.
First of all, before you actualy take off you need to figure out
where
you are flying. So press CTRL f8, find an airport that you need
then
press space bar. Now you are good to go. Just encase
you need to press CTRL enter and look up the necessary speed for
take
off and landing. Once you figured that one out you start your
engines
and ask for permission to take off by pressing f1
After you received a permission you start moving on by pressing
home
key. You should also set up your nose angle up to 12%. While
running
donw the runway you should extand your flaps by pressing CTRL F.
Once
you got to a certain speed you here a tower control telling you to
climb up to 500. Don't add more speed at that time. Also you should
retract your flaps By pressing CTRL F again and put away your
landing
gear by pressing CTRL G. Now, when the voice says take off
successfull
you can add mor speed. By pressing the R button you control your
speed.
By pressing the Z button on the keyboard you control your altitude.
Once
ou have gotten up to 500 you should level the jet by pressing the
up
button. At the same time you press T on your keyboard untill you
here
0.
It means that the jet is leveld. So with your up and down arrow
keys
you
raise or lower your nose angle. You can actually raise and lower it
up
to 39 degrees. Be carefull though, cause it is extreamly high or it
could be too low. So you would do it only if you need to change the
altitude dramaticaly. Then you start pressing your right or left
arrow
keys to set on your course. By pressing the N key you understand
how
far
to the left or to the right you have gotten. Keep the right course.
It
can change cause of the turbulance as well as your altitude could
also
change. Once you reach you destination airport you lower your speed
with
the EN button. Control it with the R buton. You have to remember
what
it
is supposed to be. Also coming close to the destination airport you
should be on 100 metres above the surface. When you receive a
permission
to land youpress your up arrow key a few times to lower your nose,
i
mean the nose of the jet to 12 degrees. Then extend your flaps and
get
your landing gear out it is done by pressin CTRL F and CTRL G. If
everything is done properly, you should have safe landing.
06.07.2017 13:59, Austin Pinto пишет:
hi all.
sorry to all the experts of the euro fly game.
i am starting my first mission and i can take off successfully.
then it tells me clim to 500 and set destination headers
something.
the plain climbs slowly any way to make clime fast?
then the real problem comes.
descend to 100 and at this point i crash.
i have red the documentations in the help center and it says press
down arrow to go up and up arrow to come done and i do that but i
cant
make it.
do i have also to reduce speed?
when i press r key at this time i can hear something like 118/97
what
is
this.
is there some demo audio tutorial that i can listen?
--
search for me on facebook, google+, orkut..
[email protected]
follow me on twitter.
austinmpinto
contact me on skype.
austin.pinto3
--
sent with mozilla thunderbird
--
sent with mozilla thunderbird
--
sent with mozilla thunderbird
--
sent with mozilla thunderbird
-=-=-=-=-=-=-=-=-=-=-=-
Groups.io Links:
You receive all messages sent to this group.
View/Reply Online (#117439): https://groups.io/g/blind-gamers/message/117439
View All Messages In Topic (15): https://groups.io/g/blind-gamers/topic/5451171
Mute This Topic: https://groups.io/mt/5451171/21656
New Topic: https://groups.io/g/blind-gamers/post
Change Your Subscription: https://groups.io/g/blind-gamers/editsub/21656
Group Home: https://groups.io/g/blind-gamers
Contact Group Owner: [email protected]
Terms of Service: https://groups.io/static/tos
Unsubscribe: https://groups.io/g/blind-gamers/leave/607459/1071380848/xyzzy
-=-=-=-=-=-=-=-=-=-=-=-
