Hi Internal wiring - cables and connectors Wiring isn't super glamorous but represents the essential network of roads that interconnect all of the appliance's internal parts and links it to the outside world.
Inside the appliance, individual wires (often multicolored to help identify function) or cables (groups of wires combined together in a single sheath or bundle) route power and control signals to the various components. Most are insulated with plastic or rubber coverings but occasionally you will find bare, tinned (solder coated), or plated copper wires. In high temperature appliances like space heaters and toasters, the insulation (if present) will be asbestos (older) or fiberglass. (Rigid uninsulated wires are also commonly found in such applications.) Particles flaking off from either of these materials are a health hazard if you come in contact, inhale, or ingest them. They are also quite fragile and susceptible to damage which may compromise their insulating properties so take care to avoid excessive flexing or repositioning of wires with this type of insulation. Fiberglass insulation is generally loose fitting and looks like woven fabric. Asbestos is light colored, soft, and powdery. Color coding will often be used to make keeping track of the wires easier and to indicate function. However, there is no standard except for the input AC line. Generally, black will be used for Hot, white will be used for Neutral, and green or uninsulated wire will be used for Safety Ground. While this is part of the NEC (Code) for electrical wiring (in the U.S.), it is not always followed inside appliances. You may also find brown for Hot, blue for Neutral, and green with a yellow stripe for Safety Ground. This is used internationally and is quite common for the cordsets of appliances and electronic equipment. Where a non-polarized plug (cordset) is used, either AC wire can be Hot and both wires will typically (but not always) be the same color. Other colors may be used for switched Hot (e.g., red), thermostat control, motor start, solenoid 1, etc. Various combinations of colored stripes may be used as well. Unfortunately, in some cases, you will find that all the wiring is the same color and tracing the circuit becomes a pain in the you-know-what. Where multiple wires need to go from point A to point B along the same path, they will often be combined into a single cable which is bundled using nylon or cloth tie-wraps or run inside a single large flexible plastic sheath. For electronic interconnects and low voltage control and signal wiring, molded flat cables are common (like those for the cables to the diskette and hard drives of your PC). These are quite reliable and can be manufactured at low cost by fully automatic machines. The thickness of the insulation of a wire or cable is not a reliable indication of its capacity or voltage rating. A fat wire may actually have a very skinny central conductor and vice-versa. In some cases, the wire conductor size and voltage rating will be printed on the insulation but this not that common. If replacement is needed, this information will be essential. However, the ampacity (maximum current) can be determined from the size of the metal conductor and for any of the line powered appliances discussed in this document, wire with a 600 V rating should be more than adequate. The type of insulation is critical in appliances that generate heat - including table lamps and other lighting fixtures. There is special high temperature insulated wire (fixture wire) which should be used when replacement is needed. For heating appliances like toasters, hair dryers, and deep friers, fiberglass or high temperature silicone based rubber insulated wire or insulating sleeves must be used should the original wiring need replacement. An appliance repair motor rebuilding shop would be the most likely source - common electronics distributors may not carry this stuff (especially if you only need a couple feet)! Connections between individual wires and between individual wires and other components are most often made by crimp or screw terminals, welding, or press-in contacts. For cables, actual multipin and socket connectors may be used. Common problems: internal wiring conductors broken, corroded, or deteriorated due to heat or moisture. Dirty, corroded, weakened, or damaged connector contacts are common requiring cleaning and reseating or replacement. Damage to insulation from vibration, heat, movement, or even improper manufacture or design is also possible. Careless reassembly during a previous repair could result in pinched broken wires or insulation as well as short circuits between wires, or wiring and sharp sheet metal parts. Testing: Inspect for obvious breaks or wires that have pulled out of their terminations. Integrity of wiring can be determined with a continuity checker or multimeter on a the low ohms scale. Flexing and wiggling wires especially at connections while observing the meter will identify intermittents. To listen to the show archives go to link http://acbradio.org/handyman.html or ftp://ftp.acbradio.org/acbradio-archives/handyman/ The Pod Cast address for the Blind Handy Man Show is. http://www.acbradio.org/news/xml/podcast.php?pgm=saturday The Pod Cast address for the Cooking In The Dark Show is. http://www.gcast.com/u/cookingindark/main.xml Visit The New Blind Handy Man Files Page To Review Contributions From Various List Members At The Following Address: http://www.jaws-users.com/handyman/ Visit the new archives page at the following address http://www.mail-archive.com/blindhandyman@yahoogroups.com/ For a complete list of email commands pertaining to the Blind Handy Man list just send a blank message to: [EMAIL PROTECTED] Yahoo! Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/blindhandyman/ <*> To unsubscribe from this group, send an email to: [EMAIL PROTECTED] <*> Your use of Yahoo! Groups is subject to: http://docs.yahoo.com/info/terms/