Hi Everyone A Tunnel for the Sun Roof-mounted skylights have been used for many years to bring the sun into our buildings, and these days a wide range of skylights are available. Tubular skylights can capture more sun than traditional skylights, even for small areas, and also provide more versatility. These units are also a basic do-it-yourself project and are available in a wide range of sizes and brands, such as Velux, Solatube, Sun-Dome, Sun Pipe and Sun-Tek.
While many skylights are more complicated, you can install a sun tube, such as the Sun-Tek Sun Tube shown in this article, in less than an afternoon. Instructions and everything you need come with the kit, including special leak-proof roof sealant. Sun-Tek's tubes consist of three parts, a sun-dome for the roof, a tube to channel the light, and a diffusing system to disperse the light evenly. As many have discovered, a simple skylight is often not the answer. It can provide light, but the light intensity changes with the amount and direction of the sun. You can have a "hotspot" of light on bright sunny days. Sun tubes eliminate this problem, providing evenly dispersed light throughout the area. And, they can also be used to direct light down through an attic and into a small area, such as a narrow hallway, even a dressing closet. They can also be used to provide natural light in a bathroom, and still maintain privacy. The first step in installation is to mark the opening for the cut-out. Measure carefully, making sure the opening is square, then drive screws up through the roof sheathing and shingles at each corner of the opening. A Close Look at the Tube The Sun-Tek's tubular skylights are available as single units, with tube sizes of 10, 14 and 21 inches and with tube length ranging from 10 to 30 feet, depending on the unit chosen. They can illuminate an area of 150 to 450 square feet. The one-piece seamless construction of the tube creates a completely leak-proof unit, and the exterior dome is made of super-tough polycarbonate that is impervious to hail and tree branches. The dome blocks 99-percent of damaging UV rays, so it is easy on carpeting and furniture. The tube is made of reflective aluminum to enhance reflectivity. Each unit comes with two elbows (15 inches in length when straightened) and one straight piece. Straight connectors are 22 inches long. In most instances additional straight connectors are needed. Also included in each kit is the diffuser lens, one tube of STS 1000 Sun-Tek butyl sealant, 10 yards of generic duct tape, and a galvanized steel (22-inch gauge) roof collar that can be used by the homeowner in the event they cut the roof opening too large. Extension connectors are available, as well as light kits that allow you to use the units for night-time lighting. The company also offers multiple-tube units, called Sun-Tek Spyder Systems, which are available with two or four tubes and a single dome skylight. These are more complicated to layout and design, as well as to install. However, they do allow for much more dispersal of light by spreading out the tubes and diffuser. For instance the Model Quad 10-inch provides four tubes, each with light capabilities of 150 square feet. We chose a Model Quad 10-inch, Spyder System for installation in a woodworking shop. The installation is somewhat different, in that the shop ceiling had not yet been installed. This not only made it easier to install the skylight, but permitted easier photography. We installed a Curb Mount Aluminum Skylight which required construction of a curb, as well as standard roof-flashing steps. Self-flashing models are also available. A 2x4 or 2x6 "curb" or frame is then contructed for the skylight. It should fit with its inside edges flush with the opening. Treated lumber, waterproof glue and deck screws were used for this assembly. A sun port with four tubes fits over the curb. It's a good idea to make sure it fits before you install the curb onthe roof. A skylight dome fits over the port and curb. Again, it's important to check for fit. The curb must be flashed into the shingles. You can make some of the flashing pieces before you get onto the roof. Installation The model we choose requires a 22-1/2-by-22-1/2-inch cutout, which allowed it to fit between our 24-inch spaced roof trusses. First step in this type of installation is to determine the location of the skylight as well as the tube lenses. Then mark the location of the cutout and drive wood screws up through the roof and asphalt shingles from the inside or underside of the roof. Up on the roof, use the protruding screws and a chalkline to outline the cut-out. Then make the cut-out with a reciprocating saw. On the roof, snap a chalkline between the protruding screws to mark the outline of the cut-out. Then cut along the chalkline through the shingles and roof sheathing. We used pressure-treated 2-by-4's for construction of the curb. It's a good idea to construct the curb, and then test the sun port and skylight for fit before installing it on the roof. The curb is made to fit with its inside edges flush with the cut-out. Place the curb over the cut-out and mark around the outside edges. Then remove the shingles down to the roofing felt using a sharp utility or roofer's knife. For the installation shown, on-site flashing is added. This begins with a flashing along the bottom edge, a piece of flashing placed under each shingle and lapping up the sides, then a top flashing. Flashing must be anchored to the curb with roofing nails, and the entire assembly must be well caulked with a good roofing sealant. Place a bead of roof sealant on the upper edges of the curb and fit the sun port down over it, then fasten in place with roofing nails. Place another bead of caulk over the outer edge of the sun-port and place the skylight down over it. Then fasten the skylight in place with the screws provided through the holes in the sides and into the curb. Lay the assembled curb on the opening and cut all around the outside edge through the shingles and down to -- but not through -- the roofing felt. Remove all shingles in the area of the curb. Using the Sun-Tek STS 1000 Sky Light sealant, run a bead around the location of the curb. Then fasten the curb in place using the screws provided (driven at an angle, or from beneath). I used 3-1/2" deck screws I had on hand, driven down from the top. The next step is to flash the curb and shingles. This can be hand-cut flashing, or a flashing kit available from Sun-Tek. Flashing must be well sealed with sealant . The sealant supplied with the kit is then applied to the top of the curb. The the sun port is installed and fastened in place with nails or screws. Sealant is applied to the top edge of the sun port. Then the dome is positioned and fastened with screws to the curb. Back off the roof and in the attic, position the sun tubes in place. Pieces of duct tape can be used to hold them temporarily together until you get them arranged as desired. Then mark locations for the ceiling holes and cut them. Once you have the tubes arranged to meet the holes, fasten the tubes, elbows and sunport drops together using the sheet metal screws provided. Then wrap with the duct tape provided. Final step is to install the diffuser lenses. Capturing the sun is fun and easy with the tubular skylight systems. You can easily install them yourself to bring in the sun and brighten your home interior anywhere you please. In the attic the tube extensions and/or elbows are assembled to the sun port. The tubes, elbows and extensions are held together with self-starting screws (provided). Then duct tape is wrapped around the joints. The bottom lens sections are then positioned in place. They are held with straps anchored to the rafters, as well as screws and tape. The final step is to snap the lens in place. In most cases this would be after the ceiling has been installed, or after a hole has been cut in the celing. Tubular Skylight Resources Solatube, www.skylightsusa.com, 1- 800-346-6991 Sun-Dome, www.solardev.com, (561) 842-8935 Sun-Tek, www.sun-tek.com, 407-859-2117 Sun Pipe, www.sunpipe.com, 1-800-844-4786 Velux, www.millworkforless.com, 1-866-645-8885 To listen to the show archives go to link http://acbradio.org/handyman.html or ftp://ftp.acbradio.org/acbradio-archives/handyman/ The Pod Cast address for the Blind Handy Man Show is. http://www.acbradio.org/news/xml/podcast.php?pgm=saturday The Pod Cast address for the Cooking In The Dark Show is. http://www.gcast.com/u/cookingindark/main.xml Visit The Blind Handy Man Files Page To Review Contributions From Various List Members At The Following address: http://www.jaws-users.com/handyman/ Visit the new archives page at the following address http://www.mail-archive.com/blindhandyman@yahoogroups.com/ For a complete list of email commands pertaining to the Blind Handy Man list just send a blank message to: [EMAIL PROTECTED] Yahoo! Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/blindhandyman/ <*> Your email settings: Individual Email | Traditional <*> To change settings online go to: http://groups.yahoo.com/group/blindhandyman/join (Yahoo! ID required) <*> To change settings via email: mailto:[EMAIL PROTECTED] mailto:[EMAIL PROTECTED] <*> To unsubscribe from this group, send an email to: [EMAIL PROTECTED] <*> Your use of Yahoo! Groups is subject to: http://docs.yahoo.com/info/terms/
