Call an appliance place in your area and find out where to get the gasket. You should not have to do any cutting it will all come in one piece.
get the make model and serial number off the fridge before you call for parts. With out this information there is no way to know what to provide you. Then re read the post that Ray just put up. His instructions go into more details than I did. -----Original Message----- From: [email protected] [mailto:[EMAIL PROTECTED] Behalf Of Rita Sent: Monday, February 12, 2007 3:00 PM To: [email protected] Subject: RE: [BlindHandyMan] refrigerator door seal Oh thank you for all these specific instructions Robert. Does this seal come in different sizes Robert or would I have to cut it? I notice there is a seam at a forty five degree angle at the corner. In one way it may be simple at that. It will be a week I'm thinking as a lot more snow is coming. Rita On Mon, 12 Feb 2007, Robert J. Moore wrote: > Hi Rita > > This should not be too difficult. > If it is like the fridge that I have, you will find screws along both sides > and the top and bottom behind the flap of the door seel. Just pull back the > flap on the inside of the door and you will find the screws. I would make > sure to have all the product off the door shelves because the inside pannal > may come loose when you take out all the screws.you just slide the old one > out and screw in the new one. If you leave a couple of screws in the bottom > and start the new one at the top this should hold the pannal in place. once > you get the new one started you can take out the final screws at the bottom > and finnish the job.Pay very close attention to how the old one is assembled > before you remove it. You want to do this with any project any way. Make > sure that the back flap is behind the door pannal and the front flap is in > front of the door pannal. > Once you have re assembled every thing It is very important to warm it up > with a hair dryer because the new seal will come folded up in a box and will > be slightly creased. Be careful not to get it so hot as to warp the rubber > seal but warm enough to make sure it is all laying nice and flat. > Good luck > Robert > > -----Original Message----- > From: [email protected] <mailto:blindhandyman%40yahoogroups.com> [mailto: [email protected] <mailto:blindhandyman%40yahoogroups.com> ]On > Behalf Of Rita > Sent: Monday, February 12, 2007 1:19 PM > To: Blind Handyman > Cc: Rita > Subject: Re: [BlindHandyMan] refrigerator door seal > > Hello Everyone, > I just had a new compressor put into my refrigerator and now I notice the > seal is not tight. I am careful to push > the door completely > shut each time. Certainly the seal needs to be replaced. How does one go > about doing this and I would need > step by step instructions as the janitor in my building has such high > prices. It is my own refrigerator. With the weather > being as it is, I may not do this for a week or so. > Any ideas would > really be appreciated. Rita > > > > [Non-text portions of this message have been removed] > > [Non-text portions of this message have been removed] To listen to the show archives go to link http://acbradio.org/handyman.html or ftp://ftp.acbradio.org/acbradio-archives/handyman/ The Pod Cast address for the Blind Handy Man Show is. http://www.acbradio.org/news/xml/podcast.php?pgm=saturday The Pod Cast address for the Cooking In The Dark Show is. http://www.gcast.com/u/cookingindark/main.xml Visit The Blind Handy Man Files Page To Review Contributions From Various List Members At The Following address: http://www.jaws-users.com/handyman/ Visit the new archives page at the following address http://www.mail-archive.com/[email protected]/ For a complete list of email commands pertaining to the Blind Handy Man list just send a blank message to: [EMAIL PROTECTED] Yahoo! Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/blindhandyman/ <*> Your email settings: Individual Email | Traditional <*> To change settings online go to: http://groups.yahoo.com/group/blindhandyman/join (Yahoo! ID required) <*> To change settings via email: mailto:[EMAIL PROTECTED] mailto:[EMAIL PROTECTED] <*> To unsubscribe from this group, send an email to: [EMAIL PROTECTED] <*> Your use of Yahoo! Groups is subject to: http://docs.yahoo.com/info/terms/
