Been there, done that. You dig a hole about a cubic foot and make at least a 12 inch square form probably just a little below grade. You fill that with cement and set the lower half of the hollow pipe pole into it. Square the post up to vertical then begin filling it up with cement tamping it thoroughly. As you approach the top of the bottom half you fit the upper half and continue tamping cement until the entire post is filled and apply the cap.
Attaching the bracket to hold the basket and back board requires only installing two 'U' bolts. If memory serves, regulation height is 10 feet 4 inches but that may be incorrect. The net I have here has three adjustment heights. We adjusted it to be regulation height at full height to permit lowering it for service and the use of little kids. This post has been up about 12 or 14 years now. Paint is beginning to flake off of it where the two lengths meed but otherwise it remains rigid. Hope this helps. Dale Leavens, Cochrane Ontario Canada [EMAIL PROTECTED] Skype DaleLeavens Come and meet Aurora, Nakita and Nanook at our polar bear habitat. ----- Original Message ----- From: David Ferrin To: [email protected] Sent: Wednesday, May 23, 2007 11:38 AM Subject: Re: [BlindHandyMan] How To Install an Exterior Light Ray, since we're on the subject of exterior installations how about finding something on installing a basket ball poll with a hoop for the kids. David Ferrin Personal Email Address [EMAIL PROTECTED] ----- Original Message ----- From: "Boyce, Ray" <[EMAIL PROTECTED]> To: <[email protected]> Sent: Tuesday, May 22, 2007 11:58 PM Subject: [BlindHandyMan] How To Install an Exterior Light Hi Everyone Take some time to read the following tips and instructions on how to install outdoor wiring. These instructions can help you save time and effort, while ensuring a safe and satisfying installation. In this document you will find information about: * Basic Rules for Outdoor Lighting Installations * Weatherproof Switches and Outlets * Underground Installation From the House * Attaching Lighting Fixtures & Outlets to Buried Cable * Installing Post Lantern Yard Lights * Proper Grounding of Outdoor Fixtures * Installing Timer Switches in Outdoor Lighting BASIC RULES FOR OUTDOOR LIGHTING INSTALLATIONS * Your first step should be to check local codes regarding outdoor lighting. Be sure to follow these code requirements carefully. * Always use type UF cable for installations requiring underground wiring. The UF implies that there must be a fuse or breaker inside the house at the starting point of the underground wiring installation. * For your outdoor lighting project, use only those materials that have an Underwriter's Laboratory (UL) approval. * Cable used for underground installations must contain a grounding conductor. Outdoor fixtures must be grounded for complete safety. * Use conduit to protect the cable where it is exposed above ground and where bends are made below ground. * Some local codes may require you to cover the entire cable with conduit. * Many local codes now require outdoor circuits to be protected with GFIs, Ground Fault Interrupters. There are two basic types of GFIs. One is designed to be installed in a circuit breaker box. The other is designed to fit into outlet boxes. Check your local code. * Always bury any underground cable at least 18" deep, but 24" is preferable. Cables buried at least 24" deep are less likely to be bothered by spading forks and other tools commonly used around the yard. * For any outside wiring installation, always use weatherproof equipment, such as boxes, receptacles, etc. * Remember to shut off the electrical current at the main switch before starting any underground wiring tie-in. Conduit must be used to cover lead cable where it is exposed or where it bends underground. WEATHERPROOF SWITCHES AND OUTLETS * Weatherproof switches and outlet boxes are available in both flush-mount or surface-mount styles. * Figure shows a flush-mounted switch and a flush-mounted receptacle. These must always be installed in a weatherproof metal switch or outlet box. * Figure shows a surface-mounted switch and outlet. These are contained in their own weatherproof boxes and can be mounted directly to any flat surface. * Figure shows a weatherproof box. These boxes can be mounted on posts or conduit when you're installing any switch or receptacle, other than the surface-mounted type. * The flush-mounted and surface-mounted switches and receptacles are designed to be completely weather resistant when they are installed correctly. Flush-Mounted Switch (on left) and Flush-Mounted Receptacle (on right) Surface-Mounted Switch (on left), Surface-Mounted Receptacle (on right). Weatherproof Box. UNDERGROUND INSTALLATION FROM THE HOUSE * Before you begin, shut off the electrical current at the main switch box. * For an underground wiring installation, mount a breaker or a fuse box in a location similar to that illustrated. The breaker box should start the installation no matter what type of cable you are using. * Run conduit from the breaker box through the wall to where the weatherproof elbow will be mounted on the outside wall. * Continue the conduit down from the weatherproof elbow to where it bends, 18" to 24" below ground. Remember, conduit is generally required where the cable bends underground. * Mount the conduit to the building foundation with conduit connectors. * Figure shows the components for wiring with conduits. (A) shows the conduit itself. (B) illustrates an adapter for attaching thin-walled conduit to rigid conduit. (C) is a coupling for connecting two pieces of conduit. (D) shows the connector used for attaching a piece of conduit to a weatherproof box. (E) is the pipe strap you should use to fasten the conduit to the wall about every 6' on exposed runs and about every 10' on concealed runs. * Your local code may require that the entire underground cable be covered with conduit. The main purpose of the conduit is to protect the cable from spading tools used in the yard. * Figure shows a conduit bender and the proper method for inserting and bending thin-walled conduit. With care and practice, you will learn to bend conduit easily. * Insert the cable through the weatherproof elbow, and then down through the conduit to the 18" to 24" level where it is to be buried. Pull the cable tightly through the weatherproof elbow and reattach the cover. The fuse box is the beginning of any underground cable installation. The conduit bender enables you to easily bend thin-walled conduit. ATTACHING LIGHTING FIXTURES & OUTLETS TO BURIED CABLE * Figure illustrates various lighting fixtures and outlet boxes that you can connect to the buried cable at any point. It's important to plan your yard lighting carefully before starting the job. * Plan ahead to determine where to install weatherproof outlet boxes. These outlet boxes are especially handy around patios and recreational areas of your yard. They provide readily accessible receptacles for appliances, record players, radios, Christmas lights, etc. * Weatherproof outlet boxes also provide handy outlets for spike lights, electric lawn mowers, electric trimmers, etc. * Install protective conduit above ground where any weatherproof outlet box or elbow is installed. You can connect various lighting fixtures and outlet boxes to the buried cable at any point. INSTALLING POST LANTERN YARD LIGHTS * Dig a hole about 2' deep with an ordinary post hole digger or tiling spade. Run cable up through the lamppost, then fill the hole with about 12" of concrete mix. Insert the lamppost into the concrete mix in an upright, plumb position. Use a long level or plumb bob to make sure the lamp is exactly straight. Remember, you cannot straighten it after the concrete hardens. * Use a bent piece of conduit to protect the turn in the cable below the post. This eliminates the danger of trouble at the turn. * You may want to use temporary stakes and guy wires to hold the post lantern in an upright position until the concrete dries. Using four guy wires in opposite directions ensures a secure post. * After the concrete is completely dry, fill in the hole with dirt and seed around the post for a neat appearance. Use a curved piece of conduit at the bend position below the post to protect the turn. PROPER GROUNDING OF OUTDOOR FIXTURES * If the conduit used in underground wiring does not connect to a grounded box, cable with a grounding conductor must be used. * Every outdoor lamp part exposed to the touch must also be grounded. See figure for one way to properly ground an ordinary post lantern. Use this same grounding procedure for almost any outside lighting installation. * Ground all weatherproof outlet boxes to an outdoor grounded box. Figures illustrate how to do this. * Figure illustrates how conduit can connect to outlet and switch boxes. Some conduit connects with a nut and bushing (A), while other conduit connects by means of a nut and set screw (B). * Ground Fault Interrupters are required in most areas for outdoor circuits. Follow the manufacturer's instructions for the installation of the type of GFI you decide to use. Two basic types are illustrated. Any part of a lamp exposed to the touch must be grounded. Outdoor outlet boxes must also be grounded. Conduit may connect to outlets and switch boxes by nuts or screws. There are two basic types of Ground Fault Interrupters (GFIs). INSTALLING TIMER SWITCHES IN OUTDOOR LIGHTING * Many of the newer outdoor lights come equipped with photoelectric eyes or motion sensors, or both. The photoelectric eye turns the light on in the evening and off in the morning. The motion detector turns the light on when it senses motion in the range of the detector. If your light does not have this type of control built in, you may wish to add a timer, photoelectric eye or a motion detector. These devices allow for automatic operation and a greater sense of security. * The figure illustrates where to install a permanent timer switch to turn an outdoor light on or off at a pre-set time. * Permanent timer switches are readily available and can be pre-set for any on/off times. Follow the manufacturer's instructions carefully when installing a permanent timer switch. * You may also use portable timer switches with plug-in equipment for outdoor lighting. Use this type of timer switch as you would any other appliance. Permanent timer switch (top), Portable timer switch (bottom). TOOL AND MATERIAL CHECKLIST * Conduit * Tiling Spade * Concrete Mix * Side-Cutter Pliers * Hacksaw * Electrical Tape * Temporary Guy Wire * Conduit Couplings & Connectors * Hacksaw Blades * Hammer * Conduit Adapters * Weatherproof Elbows * Weatherproof Switches * Timer Switch * Stakes * Ground Fault Interrupter * Conduit Bender * Weatherproof Receptacles * Underground Feed Cable (UF Cable) * Screwdriver Check your state and local codes before starting any project. Follow all safety precautions. Information in this brochure has been furnished by the National Retail Hardware Association (NRHA) and associated contributors. Every effort has been made to ensure accuracy and safety. ********************************************************************** This message and its attachments may contain legally privileged or confidential information. If you are not the intended recipient, you must not disclose or use the information contained in it. If you have received this e-mail in error, please notify the sender immediately by return e-mail and delete the e-mail. Any content of this message and its attachments which does not relate to the official business of Eraring Energy must be taken not to have been sent or endorsed by Eraring Energy. No warranty is made that the e-mail or attachment(s) are free from computer virus or other defect. ********************************************************************** [Non-text portions of this message have been removed] [Non-text portions of this message have been removed] To listen to the show archives go to link http://acbradio.org/handyman.html or ftp://ftp.acbradio.org/acbradio-archives/handyman/ The Pod Cast address for the Blind Handy Man Show is. http://www.acbradio.org/news/xml/podcast.php?pgm=saturday The Pod Cast address for the Cooking In The Dark Show is. http://www.gcast.com/u/cookingindark/main.xml Visit The Blind Handy Man Files Page To Review Contributions From Various List Members At The Following address: http://www.jaws-users.com/handyman/ Visit the new archives page at the following address http://www.mail-archive.com/[email protected]/ For a complete list of email commands pertaining to the Blind Handy Man list just send a blank message to: [EMAIL PROTECTED] Yahoo! Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/blindhandyman/ <*> Your email settings: Individual Email | Traditional <*> To change settings online go to: http://groups.yahoo.com/group/blindhandyman/join (Yahoo! ID required) <*> To change settings via email: mailto:[EMAIL PROTECTED] mailto:[EMAIL PROTECTED] <*> To unsubscribe from this group, send an email to: [EMAIL PROTECTED] <*> Your use of Yahoo! Groups is subject to: http://docs.yahoo.com/info/terms/
