Not sure the idea isn't a good one, just don't see why the blade wouldn't deflect up or down about as well as it deflects side-to-side on the present models.
Dale Leavens, Cochrane Ontario Canada [EMAIL PROTECTED] Skype DaleLeavens Come and meet Aurora, Nakita and Nanook at our polar bear habitat. ----- Original Message ----- From: robert moore To: [email protected] Sent: Tuesday, October 02, 2007 3:51 PM Subject: RE: [BlindHandyMan] Resawing planks. I am going to give away a million dollar idea. Well maybe the idea will turn out to be worth nothing or perhaps this has already been done. How about if you had a table that had a band that ran horizontal just above the table. You could raise and lower the table that way if you wanted for example shave a quarter inch off the wide surface of a 2 by 4 or a 2 by 6 you could just lay the board flat and the blade would cut along the top of the board as you fed it through. As long as you kept the board flat you should end up with a perfect cut. For what ever that hair brain idea is worth. -----Original Message----- From: [email protected] [mailto:[EMAIL PROTECTED] Behalf Of Dale Leavens Sent: Tuesday, October 02, 2007 2:17 PM To: [email protected] Subject: Re: [BlindHandyMan] Resawing planks. I think that the problem is that the band saw blade tends to deflect to one side or the other as you cut. It can apparently deflect far enough to come out the side. I would have thought you could just slice through by keeping the plank flat to a high rip fence and the blade would run true and straight but according to my reading this is inadequate. It is necessary to deflect the rip fence a few degrees off true straight so that the rear is further away from the direct line of cut than the front and in fact there are a variety of band saw rip fences actually built with a bow in them to allow for that deflection. Now I find that very interesting. It is the one unique and significant function those machines can perform I would have thought they would figure a way to get it right. There are several ways of cutting curves and shapes. I would have thought someone would have got resawing right. Dale Leavens, Cochrane Ontario Canada [EMAIL PROTECTED] <mailto:DLeavens%40puc.net> Skype DaleLeavens Come and meet Aurora, Nakita and Nanook at our polar bear habitat. ----- Original Message ----- From: Mike Rusk To: [email protected] <mailto:blindhandyman%40yahoogroups.com> Sent: Tuesday, October 02, 2007 4:21 PM Subject: Re: [BlindHandyMan] Resawing planks. Is there a way that you could attach some guide board to the front side of the board you are wanting to cut? That way you could guide it through and then remove the guide board when you are finished. I am thinking of perhaps a simmilar size board attached to the one you are cutting or perhaps a couple 1x2 boards fastened to the end so you could guide the board without getting your fingers in the cutting area. I guess it depends on how long the board is that you want to resaw. ----- Original Message ----- From: Dale Leavens To: [email protected] <mailto:blindhandyman%40yahoogroups.com> Sent: Monday, October 01, 2007 5:27 PM Subject: Re: [BlindHandyMan] Resawing planks. I've done that sort of thing with my table saw countless times too. I want to make two half in by 10 inch boards out of a rough sawn 1 by 10. The articles I read tell me to scribe a line then with a fence either deflected or a proper resawing fence which it appears is slightly crowned in line with the leading edge of the band saw I slowly guide the board on edge through the saw keeping it perpendicular using the fence but keeping the blade from wandering by steering the board following the line. I am not inclined to use my fingers to assist with this guidance. I am wondering though if there is a reasonable alternative or maybe another way which the optically enabled are less aware of since they have no need for it. I have a sense that there may be, there is a pretty big business in power feeders out there and it seems to me this may be one automated and useful application for them. As far as I know, power feeders don't watch a cut line particularly well either. Dale Leavens, Cochrane Ontario Canada [EMAIL PROTECTED] <mailto:DLeavens%40puc.net> Skype DaleLeavens Come and meet Aurora, Nakita and Nanook at our polar bear habitat. ----- Original Message ----- From: Cy Selfridge To: [email protected] <mailto:blindhandyman%40yahoogroups.com> Sent: Monday, October 01, 2007 7:13 PM Subject: RE: [BlindHandyMan] Resawing planks. I presume that, for example, you want to cut a 2x6 into two 1x6 boards? If that is the question, then no, I have not tried this with a band saw. I have, however, cut down a 1x5 board into two 1/2x5 boards using my table saw. It just took two passes to do it. Cy, the ancient oKie... _____ From: [email protected] <mailto:blindhandyman%40yahoogroups.com> [mailto: [email protected] <mailto:blindhandyman%40yahoogroups.com> ] On Behalf Of Dale Leavens Sent: Monday, October 01, 2007 9:14 AM To: [email protected] <mailto:blindhandyman%40yahoogroups.com> Subject: [BlindHandyMan] Resawing planks. Just wondering if any of you on the list with band saws has successfully resawn planks? I don't have a band saw and probably won't get one unless I can resaw fairly wide planks to make twice as many thinner wide planks. Big saws though cost a lot of money. Was wondering about the experience of listers. Thanks. Dale Leavens, Cochrane Ontario Canada HYPERLINK "mailto:DLeavens%40puc.net"[EMAIL PROTECTED] Skype DaleLeavens Come and meet Aurora, Nakita and Nanook at our polar bear habitat. [Non-text portions of this message have been removed] No virus found in this incoming message. Checked by AVG Free Edition. Version: 7.5.488 / Virus Database: 269.13.36/1041 - Release Date: 10/1/2007 10:20 AM No virus found in this outgoing message. Checked by AVG Free Edition. Version: 7.5.488 / Virus Database: 269.13.36/1041 - Release Date: 10/1/2007 10:20 AM [Non-text portions of this message have been removed] [Non-text portions of this message have been removed] [Non-text portions of this message have been removed] [Non-text portions of this message have been removed] [Non-text portions of this message have been removed] [Non-text portions of this message have been removed]
