The age-old "shtick" about a rake handle smacking you in the face when you
step on the teeth isn't funny. It's happened to me more than once. One of
the
problems is improperly storing rakes, hoes, shovels and other long-handled
tools. They can be hung up in a garage or garden shed, but usually end up
right
at the door, where they fall down, and again become a dangerous problem. The
garden tool shed shown solves the problem of long-handled tool storage and
at the same time provides a separate storage area attached to a garage or
garden shed with tools at hand. This shed could also hold trash cans. Adding
shelves in one side can provide a place for storing fertilizers and
chemicals. The shed shown doesn't have a back, but a back could be installed
to make
the shed free-standing if desired. However, it would be susceptible to
toppling over very easily, so it should be "staked" or fastened in place in
some
manner.
Properly storing garden tools, fertilizers, insecticides and pesticides is
important not only for safety, but also for ease of use. The lean-to garden
tool
shed shown is easy to build and takes the clutter out of your garage.
The siding of the shed is hardboard (barn siding) and requires two
4-by-8-foot sheets. First, crosscut 24 inches off the end of one 4-by-8-foot
sheet. This
creates the top. Rip the 6-foot piece to the correct width for the sides,
and then cut their angled ends. Some of the framing is constructed of 2-by-2
(1-1/2 x 1-1/2 inch) materials. Rip the 2-by-2's from 2-by-4's. Cut the
front and back support 2-by-2's to length. Fasten a side down over these
framing
members. Then measure and cut the bottom and top side pieces to length,
making sure the angles are correct on the top pieces. Note the bottom pieces
are
2-by-4's. Fasten these between the upright members. All siding should be
fastened in place with non-corrosive fasteners. An air brad nailer works
great
for this step. Repeat for the opposite side.
Fitted with an accessory ripping guide, a portable circ saw can be used for
ripping 2 x 4's into 2 x 2's for framing, and 1 x materials into trim
strips.
Stand the sides upright and cut the upper and lower back 2-by-4 cross
members to the correct length. Position the cross pieces between the sides
and fasten
the sides to them with non-corrosive "decking" screws. Then cut and fasten
the front 2-by-4 cross members in place in the same manner.
Stand the unit upright. Cut and install the floor joists between the front
and back lower cross members and then cut and install a 3/4-inch floor over
the
floor joists, notching to fit around the 2-by-2 uprights.
Cut the 2-by-2 door frame members and fit them in place between the front
cross pieces. The tops are held in place with a block over the back of the
top
cross piece and door upright. The bottoms are anchored to a spacer block
positioned between it and the side upright.
Use a miter saw to cut strips to length, as well as cut miter joints for
door trim.
Use a carpenter's square to make sure the assembly is square. Then rip the
front siding pieces and install them in place. Rip the upper and lower
siding
cross pieces and install them in place.
Rip the 1-1/2-inch trim pieces from a treated 1-by-6. Cut the front uprights
to length, making sure their tops follow the angle of the sides. Fasten in
place with No. 8d non-corrosive nails. An air nailer, such as the Craftsman
utility coil nailer, is perfect for this chore. Cut the upper, lower and
back
side trim boards and install them in place. Then cut the front top and
bottom trim pieces and install them as well.
Cut the door siding piece to size. Then cut the inside uprights from
2-by-2's to the correct length and fasten the siding piece down over the
uprights.
Cut the bottom and top cross 2-by-2 pieces and fasten them in place. The
door also has 1-1/2-inch trim on the outside. Cut the side door trim pieces
to
the correct length and fasten in place down over the siding with 8d
non-corrosive nails. Fasten the upper and lower cross pieces between them.
A 24-volt portable circular saw makes quick work of cutting siding and
framing pieces.
Angled door cross trim pieces add to the décor. Cut these to fit and fasten
in place. Then hang the door and install the hook. You may desire to add a
latch,
or hasp, if you prefer to have a means of locking the shed.
Cut the interior rafters to size, following the angles of the front and back
cross members. One method of doing this is to lay a rafter across the top of
the cross members and then use a block of wood held against both pieces to
mark the angle on the rafters. Install between the cross members. Install
the
hardboard top piece for the roof down over the rafters. The top can be left
as is, but it's best to apply roll roofing or composite shingles to match
the
existing building. Then paint or stain to match existing buildings.
Anchor the completed shed to the outside of a building with screws through
the top back cross piece into the building. Apply caulking on the back of
the
roof edge and to the adjoining building. Finally, fasten the top back trim
strip down over the caulk and to the shed top and the adjoining building.
Framing is fastened together with a framing nailer, siding is installed with
brad nailer, and then the trim is installed.
Materials List
Sides, 3/8" siding, 22 x 72", cut to angle, 2 req'd.
Side front upright, 2 x 2 x 66", 2 req'd.
Side rear upright, 2 x 2 x 72", 2 req'd.
Side bottom cross member, 2 x 4 x 19", 2 req'd.
Side top cross member, 2 x 2 x 19", 2 req'd.
Rear bottom back and front cross members,
2 x 4 x 42", 2 req'd.
Front top and rear cross members, 2 x 4 x 42", 2 req'd.
Floor joists, 2 x 4 x 19", 2 req'd.
Rafters, 2 x 4 x 19", 2 req'd.
Floor, 3/4" plywood x 22 x 45", cut to fit, 1 req'd.
Door frame uprights, 2 x 2 x 59", 2 req'd.
Door frame blocking, 2 x 2 x 8", 4 req'd.
Front siding pieces, 3/8" hardboard x 16 x 66
2 req'd.
Upper front siding, 3/8" hardboard x 3-1/4 x 29",
1 req'd.
Lower front siding, 3/8" hardboard x 3-1/2 x 29",
1 req'd.
Front upright trim, 3/4 x 1-1/2 x 59", 2 req'd.
Side upright trim, 3/4 x 1-1/2 x 66", 2 req'd.
Bottom front trim, 3/4 x 3-1/2 x 42", 1 req'd.
Top front trim, 3/4 x 3-1/4 x 42", 1 req'd.
Door uprights, 2 x 2 x 58-1/2", 2 req'd.
Door inside cross members, 2 x 2 x 28-1/2",
2 req'd.
Door inside upright members, 2 x 2 x 58-1/2",
2 req'd.
Door siding, 3/8" hardboard x 28 1/2 x 58-1/2",
1 req'd.
Door upright trim, 3/4 x 1-1/2 x 58-1/2", 2 req'd.
Door horizontal trim, 3/4 x 1-1/2 x 28-1/2",
2 req'd.
Door cross member trim, 3/4 x 1-1/2 x 62",
cut to fit, 2 req'd.
Top side trim, 3/4 x 1-1/2 x 22", cut to angle,
2 req'd.
Bottom side trim, 3/4 x 1-1/2 x 20-1/2", 2 req'd.
Back side trim, 3/4 x 1-1/2 x 69",
angle cut to fit, 2 req'd.
Top, 3/8" plywood, 22 x 45", 1 req'd.
Shingles to fit
Top back trim strip, 3/4 x 1-1/2 x 45", 1 req'd.
Screen door hook, 1 req'd.
Other Garden Tool Storage Solutions
If you don't want to build an outside shed, or don't have the room for it,
garage storage systems are also available. Craftsman has just introduced
their
Storage Solutions System. These storage units can fill a 5-, 8-, 12- or
16-foot wall with freestanding cabinets with or without shelves. Wall and
mobile
cabinets can store all kinds of garden gear and tools. You can start with
the entire system, which also includes a handy workbench that can double as
a
garden potting bench. Or you can purchase individual pieces and add pieces
as you need to expand. Exclusive features of the units include
zero-clearance
radius doors, allowing the cabinets to rest flush against the wall and
adjacent to other storage units. Heavy-duty tubular steel frames on top and
bottom
provide rigidity. The doors close similar to car doors. Tension is
adjustable based on the weight in the door. This allows doors loaded with
chemicals,
fertilizer and other heavy items to open easily and close securely.
The new Craftsman Garage Storage Solutions helps organize garden tools and
other gear.
Another alternative is the Mitchell Garage Cabinet Systems. Designed
specifically for garage installation they come in a range of sizes,
including cabinets
72 inches high for storing long-handled tools and other items. The cabinets
are suspended on a steel-rail support system, allowing easy installation at
any height off the floor, keeping the cabinets dry and the underneath easy
to clean. Another benefit of the system is the cabinets can be easily
relocated.
Cabinets are made of high density 3/4-inch particle board, with doors of
furniture-grade medium density fiberboard. Three-way adjustable Euro-style
hinges
and shelf adjustment holes are standard features.
The Mitchell Garage Cabinet System has several different sized cabinets
available for storing garden tools, gear as well as chemicals and
fertilizer.
