Every router table made for a table saw that I have seen mounts on the side replacing the extension table. You can then use the saws rip fence and by expanding the miter gauge you can use it as well. Lenny ----- Original Message ----- From: "Scott Howell" <[EMAIL PROTECTED]> To: <[email protected]> Sent: Tuesday, July 22, 2008 4:05 PM Subject: Re: [BlindHandyMan] question on holding stock while using a router
Well that's a good question, I'd have to measure the router and the space on the table. I swear it looks like it would fit. Not sure how much space I'd need, but going to check it out for grins if nothing else. On Jul 22, 2008, at 3:32 PM, john schwery wrote: > Scott, I doubt if your table saw would work because a router table > needs an opening big enough for the plate that attaches to the router > base. In this way, the plate that holds the router is on the same > level as the table when the plate is put into the opening in the > table. I have never seen a table saw with a big enough opening to > accommodate a router. > > earlier, Scott Howell, wrote: > > >You know you guys are way smarter than me. I never thought of the > >double-sided tape and Dan you are correct, the piece is longer than > >what I need which I forgot. So, in fact it would be quite possible to > >if not clamp, surely tape. I really like the idea of the temporary > >router table and I'm going to have to check into this a bit more. I > >could very easily take my table saw which has a piece of the table > >that expands and leaves this nice large opening I could easily fit a > >piece into for making a table. Matter of fact I even have the perfect > >piece here already which is pretty heavy. THanks all for the ideas > and > >also if anyone has any suggestions on how to make the piece that I'd > >mount the router too in my table, I'd appreciate it. I may be wrong > >not having seen a table with the router installed, but I assume there > >are holes in the router base plate that you'd drive screws which hold > >the router in place. This I assume puts the base of the router > >slightly lower than the mounting plate and table surface. Is that > >correct? I have a pretty thick piece, don't know, but perhaps a half > >inch piece of malimeen that would work perfectly for the table > >surface. WOw, you guys are really awesome. > > > >tnx > >On Jul 22, 2008, at 7:33 AM, Dale Leavens wrote: > > > > > Hello, > > > > > > The usual way to do this without a router table is to lay the > narrow > > > board along with another on a work bench or table to widen the > > > surface. They should be the same thickness. You then stick them > down > > > with double sided tape or if the parallel board is wide enough you > > > can also clamp it down. Then using a round over bit or what ever > > > profile you wish, preferably with a pilot bit you run the router > > > along the edge to be routed. > > > > > > A two inch board is pretty narrow to guide a router along without > > > more support for the base. It will tend to rock and spoil your > cut. > > > > > > I also have a fairly large piece of particle board with a round > hole > > > which includes a shoulder to hold a router and clamp an temporary > > > fence to it and clamp it to the edge of my work table. This has > > > formed a large temporary router table. While I don't use it any > more > > > I can't bring myself to throw it away. > > > > > > ----- Original Message ----- > > > From: Scott Howell > > > To: > > > <mailto:blindhandyman%40yahoogroups.com>[email protected] > > > Sent: Tuesday, July 22, 2008 5:21 AM > > > Subject: [BlindHandyMan] question on holding stock while using a > > > router > > > > > > Hey folks, I was thinking about this little project and ran into a > > > small problem. I have a piece of one by two that I want to take a > > > router and make a rounded edge. So, I got to thinking that I don't > > > have a table so just cant run the piece through, but of course in > > > order to do it free-hand I'd have to hold the piece still. So, not > > > having used a router enough to really know how this would work, > I was > > > wondering what would be the best way to hold the piece still? I > > > thought of putting it in a vice and leaving enough room for the > bit to > > > do its job and that might be the best option, but I thought I'd > ask > > > and see if others had any better ideas. I didn't want to screw > it down > > > to any thing if I could avoid it. The plan in the end is to > round off > > > the edge, make some plugs to hide the screws, stain it, and > mount it > > > to the front edge of my wife's desk. I think it'll look nice > once I've > > > got it finished. > > > > > > tnx > > > > > > Scott Howell > > > <mailto:s.howell%40verizon.net>[EMAIL PROTECTED] > > > > > > ---------------------------------------------------------- > > > > > > No virus found in this incoming message. > > > Checked by AVG. > > > Version: 7.5.524 / Virus Database: 270.5.2/1562 - Release Date: > > > 7/19/2008 2:01 PM > > > > > > [Non-text portions of this message have been removed] > > > > > > > > > > > > >Scott Howell > ><mailto:s.howell%40verizon.net>[EMAIL PROTECTED] > > > >[Non-text portions of this message have been removed] > > > > > >No virus found in this incoming message. > >Checked by AVG - http://www.avg.com > >Version: 8.0.138 / Virus Database: 270.5.4/1566 - Release Date: > >7/22/2008 6:00 AM > > [Non-text portions of this message have been removed] > > > Scott Howell [EMAIL PROTECTED] [Non-text portions of this message have been removed] ------------------------------------ Send any questions regarding list management to: [EMAIL PROTECTED] To listen to the show archives go to link http://www.acbradio.org/pweb/index.php?module=pagemaster&PAGE_user_op=view_page&PAGE_id=33&MMN_position=47:29 Or ftp://ftp.acbradio.org/acbradio-archives/handyman/ The Pod Cast address for the Blind Handy Man Show is. http://www.acbradio.org/news/xml/podcast.php?pgm=saturday Visit The Blind Handy Man Files Page To Review Contributions From Various List Members At The Following address: http://www.jaws-users.com/JAWS/handyman/ Visit the archives page at the following address http://www.mail-archive.com/[email protected]/ If you would like to join the JAWS Users List, then visit the following address for more information: http://www.jaws-users.com/ For a complete list of email commands pertaining to the Blind Handy Man list just send a blank message to: [EMAIL PROTECTED] Groups Links __________ NOD32 3288 (20080722) Information __________ This message was checked by NOD32 antivirus system. http://www.eset.com
