Thanks Ron. In this case the two extensions where necessary. ONe to the light because rerouting although possible would have been a really difficult operation, but certainly something I can go back and change. THe extension of the power feed going to the switch was necessary only because rerunning the feed would have required starting at the distribution panel and I'm not going to do that. I don't really want to take the risk with an unfamiliar panel. grin I figured 200 amps is not something to take lightly. grin.
Thanks again, On Sep 13, 2009, at 10:33 PM, Ron Yearns wrote: > The only requirements on junction boxes is that they be accessible > and have a removable cover. Be careful you don't add too many cable > and wires so it exceeds it capacity. > Ron > ----- Original Message ----- > From: Scott Howell > To: [email protected] > Sent: Sunday, September 13, 2009 6:20 AM > Subject: [BlindHandyMan] Bathroom Switch Relocation Complete > > Well my friends, this project was not nearly as bad as it seemed and > only with two ugly problems and yet I have just one question. > First the ugly issues cause we all like those. I damn near drilled a > hole where one was not needed, but attention in this case paid off > without a doubt. First I cut the hole for the box and let me tell you > it was tight, but it fit and I did not have to do anything more than > cut the hole for the box. The duct that was on one side and the stud > on the other provided just enough space to get the box installed, but > it did take a little force to get things moving, but hey it worked. > The ugly issue was after cutting the hole I ran my fish tape up to try > and determine if there was an opening at the top of the wall or what. > Did not seem to be the since the tape just seem to stop. So, I figured > it would require a little drilling and when I started it just didn't > feel right. Glad I stopped because I think in fact if there had not > been tile in the bathroom above where I was, I may have come through > the floor. grin What I subsequently discovered with the help of my > good friend, is two things. First after I stopped attempting to drill > a hole, I ran the tape back in there and suddenly it must have just > flipped at the right point because I could hear it bouncing around in > the ceiling, above the door. Okay, but my sighted buddy couldn't see > the tape. However, I could feel it from the utility room side. THere > is a space between the ceiling and underside of the floor which is > open do to the duct. So the tape was hiding down along side the duct > and I was able to grab it and pull it through the opening where the > duct left the utility room and went into the hall. I'll not bore you > with the details of the opening, but it is sort of interesting. In any > event, I was able to drag the wires for the fan, light, and power to > the new location. So, here are a couple of questions. > > 1. Does a junction box have to face into the room in which the > switches are located? In other words, currently the junction box is > behind the door in the bathroom. What I did is tied a feed off the > main power coming into the box, ran that over and down to the switch > which is okay since it is in the junction box. What I wanted to do > initially is take the box out, flip it around, and reinstall so the > cover faced into the utility room. This would make it easier to work > on and if the power is off and someone needed to see the wires, the > lights in the utility room are on a separate circuit. > 2. Is it acceptable to extend a line provided it is again, in a > junction box? What I ended up doing was instead of running an entire > new line from the light fixture to the switch, I took the line that > had originally been in the junction box, tied an additional piece on, > and extended that to the switch. I can easily go back and correct this > if it is not appropriate, but I was running out of time and needed to > put the bathroom back in service until I was ready to go back and > finish off the other remaining items, such as patching and the like. > Oh, that reminds me, I did have one other ugly problem that required > an opening be made above the door. Seems at one point while pulling > the first set of wires through, the tape became stuck and nothing I > did could work it loose. I ended up cutting a hole above the door so I > could get my hand in there and found the tape had become trapped > between the stud and a cross member. I had to wedge a screwdriver down > in there and sort of pry things just enough to get the tape loose. > Luckily for me it worked out. That hole came in handy for the third > wire run since that tape seem to constantly want to get stuck at the > same point and there was no working around that snag. > Well thanks all for reading my ramblings and for your suggestions. > > [Non-text portions of this message have been removed] > > [Non-text portions of this message have been removed]
