It sounds like you were offended when I said that I don't think many of us have a band saw. I had no intention of offending you and I don't see anything offensive about it. What I was alluding to was that this is the blindhandyman list, not the blindwoodworker site, so many of us don't have an arsenal of woodworking tools. I do a lot of woodworking projects and I don't even have a bandsaw myself. So, I hope you can see now that there was nothing offensive about it.
From: [email protected] [mailto:[email protected]] On Behalf Of Matt Sent: Friday, November 20, 2009 3:59 PM To: [email protected] Subject: Re: [BlindHandyMan] Re: another measuring device: Oh for instance, you set your table saw's fence by laying a 1 by 4 on edge, so that it will cut as thick as that board, then you lay it down and run it through. Equal square, as thick as it is wide. That's what I meant. So, I'm spoiled having my bandsaw am I? hahahahahah, It was one of my first tools. Maybe my 4th. Think I bought drillpress, sander and compound miter first. ----- Original Message ----- From: Tom Hodges To: [email protected] <mailto:blindhandyman%40yahoogroups.com> Sent: Friday, November 20, 2009 7:35 AM Subject: RE: [BlindHandyMan] Re: another measuring device: First of all, I don't think many of us have a band saw. Next, what is a square equal stick? From: [email protected] <mailto:blindhandyman%40yahoogroups.com> [mailto:[email protected] <mailto:blindhandyman%40yahoogroups.com> ] On Behalf Of Matt Sent: Thursday, November 19, 2009 9:54 PM To: [email protected] <mailto:blindhandyman%40yahoogroups.com> Subject: Re: [BlindHandyMan] Re: another measuring device: I don't know why you guys don't just use a fence, or set one up on the bandsaw and feed it so far with a stop, then either grab it on the other side of the blade and pull it through, or pull it out and feed it the other way until you met in the middle. Even if you got a rough edge you could always straiten it out on the sander afterwards? I intend to try a square equal stick instead of messing with flattening a dowel. Mainly because I hate to waste the dowel. Matt ----- Original Message ----- From: Tom Vos To: [email protected] <mailto:blindhandyman%40yahoogroups.com> <mailto:blindhandyman%40yahoogroups.com> Sent: Thursday, November 19, 2009 6:45 PM Subject: RE: [BlindHandyMan] Re: another measuring device: Tom, Your metal tubing idea would be a good one. I don't do much metal work, but this would be a great way to go. If I had to flatten a side of the dowel by hand I would probably work it with a rasp, with the dowel clamped hear the edge of my work bench. After I got part of it flattened, maybe I could get a small saw in there to finish the job. As usual, hand tools take more time. Could you get part of it cut with a plane? Blessings, tom -----Original Message----- From: [email protected] <mailto:blindhandyman%40yahoogroups.com> <mailto:blindhandyman%40yahoogroups.com> [mailto:[email protected] <mailto:blindhandyman%40yahoogroups.com> <mailto:blindhandyman%40yahoogroups.com> ]On Behalf Of Tom Fowle Sent: Thursday, November 19, 2009 12:34 PM To: blindHandyMan Subject: [BlindHandyMan] Re: another measuring device: tom, This is a very fancy and neat "story stick." idea. I'm trying to think of how to do the half flat on the dowell without power tools I wonder if one could get a chunk of square extruded tubing and a rod that'd fit it. This might allow one to tap the bolt into the outside square piece thus avoiding the need for the half flat. Also might be more stable with the square outside. Just pondering how to make it all much too fancy and hard <GRIN> Neat design. Tom Fowle [Non-text portions of this message have been removed] [Non-text portions of this message have been removed] [Non-text portions of this message have been removed] [Non-text portions of this message have been removed] [Non-text portions of this message have been removed]
