it is a spiral saw
----- Original Message -----
From: Max Robinson
To: [email protected]
Sent: Thursday, January 07, 2010 9:06 PM
Subject: Re: [BlindHandyMan] RotoZip
What is a roto zip? Is it something like a Dremel tool?
Regards.
Max. K 4 O D S.
Email: [email protected]
Transistor site http://www.funwithtransistors.net
Vacuum tube site: http://www.funwithtubes.net
Music site: http://www.maxsmusicplace.com
To subscribe to the fun with transistors group send an email to.
[email protected]
To subscribe to the fun with tubes group send an email to,
[email protected]
----- Original Message -----
From: "Tom Hodges" <[email protected]>
To: <[email protected]>
Sent: Thursday, January 07, 2010 11:33 AM
Subject: RE: [BlindHandyMan] RotoZip
> My Roto Zip has a shoe that is about an inch and a half in diameter and
> can
> be adjusted for the depth of the bit. It's basically free hand unless you
> are cutting in a straight line and you could lay a straight edge next to
> your work for a guide. Also, when cutting drywall, your guide is the door
> jamb or electrical outlet box or whatever you are cutting out around.
> When
> cutting out something, I always travel from right to left with it so it
> will
> hug the guide. If I were cutting out drywall, for instance, from around a
> door jamb and went left to right, the roto zip wants to walk away from the
> jamb instead of staying right there next to it.
>
>
>
> The bits for mine are an eighth inch diameter and about an inch and a half
> to two inches long, total. About a half to three quarters of an inch of
> it
> go into the collet. I have bits for drywall and wood but I think they
> also
> have them for ceramic, light sheet metal, etc.
>
>
>
> Hope this helps.
>
>
>
> Tom
>
>
>
> From: [email protected] [mailto:[email protected]]
> On Behalf Of William Stephan
> Sent: Thursday, January 07, 2010 10:47 AM
> To: [email protected]
> Subject: RE: [BlindHandyMan] RotoZip
>
>
>
>
>
> Tom: I've only tried using rotozip bits on a drill press with disasterous
> results, so I'm curious about how you use yours. I have a friend who says
> he uses one of these, but he I think just puts a bit in a high speed drill
> and cuts freehand. So, is there a shoe on your tool that allows you to
> follow a fence or jig?
>
> Thanks for any illumination.
>
> -----Original Message-----
> From: [email protected]
> <mailto:blindhandyman%40yahoogroups.com>
> [mailto:[email protected]
> <mailto:blindhandyman%40yahoogroups.com> ]
> On Behalf Of Tom Hodges
> Sent: Thursday, January 07, 2010 08:30
> To: [email protected] <mailto:blindhandyman%40yahoogroups.com>
> Subject: [BlindHandyMan] RotoZip
>
> Someone was inquiring about using the roto zip for cutting wood the other
> day and I have since deleted them. However, I had occasion to use mine
> yesterday to cut wood and here is the result.
>
> I'm tearing out an old closet and building a new one in a 100 year old
> house. The exterior wall is brick, inside and out. I had to remove the old
> baseboard from the wall in the new closet section only so I could put in a
> new one all around the interior of the closet. I put a wood cutting bit
> into the Roto Zip and adjusted it to the thickness of the baseboard, which
> was a full, one inch thick and seven and a half inches high. I cut it to
> about a quarter inch from the floor in about 30 seconds and chiseled the
> remaining quarter inch.
>
> It worked beautifully. Prior to this, I had only used my Roto Zip for
> cutting drywall. The trick to using the Roto Zip would be to use the right
> bit for the material being cut. The drywall bit will definetly not cut
> wood.
>
> [Non-text portions of this message have been removed]
>
> [Non-text portions of this message have been removed]
>
>
>
>
>
> [Non-text portions of this message have been removed]
>
>
>
> ------------------------------------
>
> Send any questions regarding list management to:
> [email protected]
> To listen to the show archives go to link
>
http://www.acbradio.org/pweb/index.php?module=pagemaster&PAGE_user_op=view_page&PAGE_id=33&MMN_position=47:29
> Or
> ftp://ftp.acbradio.org/acbradio-archives/handyman/
>
> The Pod Cast address for the Blind Handy Man Show is.
> http://www.acbradio.org/news/xml/podcast.php?pgm=saturday
>
> Visit The Blind Handy Man Files Page To Review Contributions From Various
> List Members At The Following address:
> http://www.jaws-users.com/JAWS/handyman/
>
> Visit the archives page at the following address
> http://www.mail-archive.com/[email protected]/
>
> If you would like to join the JAWS Users List, then visit the following
> address for more information:
> http://www.jaws-users.com/
> For a complete list of email commands pertaining to the Blind Handy Man
> list just send a blank message to:
> [email protected]! Groups Links
>
>
>
>
----------------------------------------------------------
No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.431 / Virus Database: 270.14.128/2604 - Release Date: 01/06/10
19:35:00
[Non-text portions of this message have been removed]
