On Wed, Aug 10, 2022 at 11:10 AM Nikolay Aleksandrov <[email protected]> wrote: > > On 10/08/2022 18:00, Sevinj Aghayeva wrote: > > On Wed, Aug 10, 2022 at 10:50 AM Nikolay Aleksandrov > > <[email protected]> wrote: > >> > >> On 10/08/2022 17:42, Sevinj Aghayeva wrote: > >>> > >>> > >>> On Wed, Aug 10, 2022 at 4:54 AM Nikolay Aleksandrov <[email protected] > >>> <mailto:[email protected]>> wrote: > >>> > >>> On 10/08/2022 06:11, Sevinj Aghayeva wrote: > >>> > When bridge binding is enabled for a vlan interface, it is expected > >>> > that the link state of the vlan interface will track the subset of > >>> the > >>> > ports that are also members of the corresponding vlan, rather than > >>> > that of all ports. > >>> > > >>> > Currently, this feature works as expected when a vlan interface is > >>> > created with bridge binding enabled: > >>> > > >>> > ip link add link br name vlan10 type vlan id 10 protocol 802.1q \ > >>> > bridge_binding on > >>> > > >>> > However, the feature does not work when a vlan interface is created > >>> > with bridge binding disabled, and then enabled later: > >>> > > >>> > ip link add link br name vlan10 type vlan id 10 protocol 802.1q \ > >>> > bridge_binding off > >>> > ip link set vlan10 type vlan bridge_binding on > >>> > > >>> > After these two commands, the link state of the vlan interface > >>> > continues to track that of all ports, which is inconsistent and > >>> > confusing to users. This series fixes this bug and introduces two > >>> > tests for the valid behavior. > >>> > > >>> > Sevinj Aghayeva (3): > >>> > net: core: export call_netdevice_notifiers_info > >>> > net: 8021q: fix bridge binding behavior for vlan interfaces > >>> > selftests: net: tests for bridge binding behavior > >>> > > >>> > include/linux/netdevice.h | 2 + > >>> > net/8021q/vlan.h | 2 +- > >>> > net/8021q/vlan_dev.c | 25 ++- > >>> > net/core/dev.c | 7 +- > >>> > tools/testing/selftests/net/Makefile | 1 + > >>> > .../selftests/net/bridge_vlan_binding_test.sh | 143 > >>> ++++++++++++++++++ > >>> > 6 files changed, 172 insertions(+), 8 deletions(-) > >>> > create mode 100755 > >>> tools/testing/selftests/net/bridge_vlan_binding_test.sh > >>> > > >>> > >>> Hi, > >>> NETDEV_CHANGE event is already propagated when the vlan changes flags, > >>> > >>> > >>> I'm not sure if NETDEV_CHANGE is actually propagated when the vlan > >>> changes flags. The two functions in the bridge module that handle > >>> NETDEV_CHANGE are br_vlan_port_event and br_vlan_bridge_event. I've > >>> installed probes for both, and when I'm changing flags using "sudo ip > >>> link set vlan10 type vlan bridge_binding on", I don't see any of those > >>> functions getting called, although I do see vlan_dev_change_flags getting > >>> called. I think there may be a bug in core/dev.c:__dev_notify_flags. > >> > >> are both vlan and bridge interfaces up? > >> what exactly are you probing for? > > > > > > I first run the attached pre.sh script that sets up the environment > > and creates a vlan interface with bridge binding off. I then start > > recording with perf, and here's the list of probes: > > > > $ sudo ./k/linux/tools/perf/perf probe -l > > probe:br_vlan_bridge_event (on br_vlan_bridge_event in bridge with event > > dev) > > probe:br_vlan_port_event (on br_vlan_port_event in bridge with event) > > probe:br_vlan_set_vlan_dev_state (on br_vlan_set_vlan_dev_state in > > bridge with br vlan_dev) > > probe:register_vlan_dev (on register_vlan_dev in 8021q with dev) > > probe:vlan_changelink (on vlan_changelink in 8021q with dev) > > probe:vlan_dev_change_flags (on vlan_dev_change_flags in 8021q with dev) > > probe:vlan_dev_fix_features (on vlan_dev_fix_features in 8021q with dev) > > probe:vlan_dev_init (on vlan_dev_init in 8021q with dev) > > probe:vlan_dev_ioctl (on vlan_dev_ioctl in 8021q with dev) > > probe:vlan_dev_open (on vlan_dev_open in 8021q with dev) > > probe:vlan_dev_stop (on vlan_dev_stop in 8021q with dev) > > probe:vlan_dev_uninit (on vlan_dev_uninit in 8021q with dev) > > probe:vlan_newlink (on vlan_newlink in 8021q with dev) > > > > I then run the following command to turn the bridge binding flag on: > > > > $ sudo ip link set vlan10 type vlan bridge_binding on > > > > Then I stop the recording and print out the events, and I see this. I > > don't see br_vlan_port_event or br_vlan_bridge_event getting called. > > > > ip 5933 [003] 2204.722470: > > probe:vlan_changelink: (ffffffffc1042b50) dev="vlan10" > > ip 5933 [003] 2204.722476: > > probe:vlan_dev_change_flags: (ffffffffc1042600) dev="vlan10" > > > > Am I doing something wrong? > > > > Thanks > > > > > > You can't expect to see br_vlan_bridge_event() called because the notification > target device is vlan10 and not the bridge. See br_device_event(): > ... > if (netif_is_bridge_master(dev)) { > err = br_vlan_bridge_event(dev, event, ptr); > if (err) > return notifier_from_errno(err); > ... > > > Try probing for br_device_event(), you'll see it gets called every time you > change the flag. > You're right, I did see br_device_event() getting called. Thanks!
-- Sevinj.Aghayeva
