On Mon, Jan 10, 2005 at 02:53:10PM -0500, Neil Horman wrote:
> Gergely Madarasz wrote:
> >On Mon, Jan 10, 2005 at 02:41:34PM -0500, Neil Horman wrote:
> >
> >>Gergely Madarasz wrote:
> >>
> >>>On Mon, Jan 10, 2005 at 12:40:57PM -0500, Neil Horman wrote:
> >>>
> >>>
> >>>>Gergely Madarasz wrote:
> >>>>
> >>>>
> >>>>>On Mon, Jan 10, 2005 at 11:04:55AM -0500, Neil Horman wrote:
> >>>>>
> >>>>>
> >>>>>
> >>>>>>Strange. My concern was that the tg3 interface has its hardware
> >>>>>>reset whenever its set to be up, and part of that is a resetting of
> >>>>>>its receive mode. If for some reason IFF_PROMISC was cleared after
> >>>>>>you set it using brctl, the interface might be taken out of promisc
> >>>>>>mode. Do you have any iptables rules running that might drop bpdus?
> >>>>>
> >>>>>
> >>>>>No iptables rules az all. Btw iptables wouldn't prevent tcpdump from
> >>>>>seeing the packets, would it?
> >>>>>Could it be that the driver perhaps has a problem setting promisc mode
> >>>>>when resetting the hardware?
> >>>>>
> >>>>
> >>>>Not really sure about this. One experiment is worth a thousand guesses
> >>>>I suppose....... I'll try and let you know. :)
> >>>
> >>>
> >>>I did some other checks, like adding an explicit ifconfig eth0 promisc,
> >>>then looking at tcpdump output - I didn't see any stray packets like I
> >>>usually do, just ethernet broadcasts and unicasts to my mac, this also
> >>>points to a problem that the ethernet interface is actually not in
> >>>promisc, while the driver thinks it is.
> >>>
> >>>And it is probably not a driver-only issue. I've got older machines with
> >>>tg3 running fine with bridge (with an older tg3 driver), and eth1 on the
> >>>same machine also runs fine. On another machine I tested today, an IBM
> >>>x326, the same thing happens - eth0 broken, eth1 fine. Would access to
> >>>one
> >>>of these machines help? :)
> >>>
> >>>Greg
> >>
> >>I've got a tg3 card here. I'll try re-create it as soon as I have time.
> >
> >
> >Sounds great, but I expect it will not occur with a random tg3 card,
> >explained above...
> >
> Mmmmm....post your lspci -vvv entry for your broken tg3 card?
on the ibm x346:
0000:05:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5721
Gigabit Ethernet PCI Express (rev 01)
Subsystem: IBM: Unknown device 02c6
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 0x10 (64 bytes)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at cfff0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3
Enable-
Address: bfa4b67f4b6720bc Data: aadf
Capabilities: [d0] #10 [0001]
The other one looks the same, just bus 06 instead of 05 and different
Region 0 and Address lines.
Same problem, other machine (ibm x326):
0000:02:01.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5704
Gigabit Ethernet (rev 03)
Subsystem: IBM: Unknown device 02a6
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (16000ns min), Cache Line Size: 0x10 (64 bytes)
Interrupt: pin A routed to IRQ 24
Region 0: Memory at fe010000 (64-bit, non-prefetchable) [size=64K]
Region 2: Memory at fe000000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3
Enable-
Address: 3aaf3ffdeb65f8f4 Data: b0db
Greg
_______________________________________________
Bridge mailing list
[email protected]
http://lists.osdl.org/mailman/listinfo/bridge
