Ooo! Stuva maybe will be good. I plan use 2x ikea lack (because our printers are little bit tall) tommorow i measure it and bring good spool of PLA.
rainbof. so 1. 4. 2023 v 18:55 odesílatel Josef Šmidrkal via Brmlab <brmlab@brmlab.cz> napsal: > Just a reminder, there is a dormant 3d printer enclosure, built from IKEA > STUVA. > If you enter HW Lab, it's the white box on the floor on your left. > > https://www.reddit.com/r/3Dprinting/comments/hfjbff/ikea_stuva_enclosure/ > > Perhaps it can be reused. > > --cgi > > On 31/03/2023 7:21 pm, Ondrej Beranek wrote: > > I think not good point :) > > In brmlab, specially in hwlab, you cant print anything from petg because > printers are placed in "windy" place. If we can print from petg we need > petg and box. I create on from paper but somewho trash it :). > > I think we need few plates from acryl and make hard case from ikea lack. > > If brm pay it, i build it :). > > Rainbof > > Dne pá 31. 3. 2023 17:43 uživatel Vasiliy Chernov <tusk1...@gmail.com> > napsal: > >> Fair point. Thanks! >> >> On Fri 31. 3. 2023 at 17:16, Jan Hrach <je...@hrach.eu> wrote: >> >>> To be honest, we print at work from PETG, ASA and ABS without enclosure >>> and without dryer (Prusa MK3). It was not much better with the enclosure... >>> Way more influence is by the mode (e.g. adding stress relief slots, mouse >>> ears to help with adhesion etc.) >>> >>> Btw. you should probably take this discussion to brmlab@ >>> >>> On 31. 03. 23 14:27, Vasiliy Chernov via Rada wrote: >>> > Hi Everyone, >>> > >>> > I found today this box for 3D printer: >>> > https://www.majkl3d.cz/p/creality-kryt-na-3d-tiskarnu >>> > >>> > It seems like a great solution for our printer. Relatively cheap and >>> will allow to print different types of filament (not only PLA as it is >>> today). >>> > >>> > Also, I can order filament dryer. It is a bit more expensive on that >>> website than on Aliexpress. So, if everybody is fine, we can order either >>> just that one, or both. >>> > >>> > What do you think? >>> > Cheers! >>> > >>> > _______________________________________________ >>> > Rada mailing list >>> > r...@brmlab.cz >>> > https://brmlab.cz/cgi-bin/mailman/listinfo/rada >>> >>> -- >>> Jan Hrach | https://jenda.hrach.eu/ >>> >>> _______________________________________________ >>> Brmlab mailing list >>> Brmlab@brmlab.cz >>> https://brmlab.cz/cgi-bin/mailman/listinfo/brmlab >>> >> _______________________________________________ >> Brmlab mailing list >> Brmlab@brmlab.cz >> https://brmlab.cz/cgi-bin/mailman/listinfo/brmlab >> > > _______________________________________________ > Brmlab mailing > listBrmlab@brmlab.czhttps://brmlab.cz/cgi-bin/mailman/listinfo/brmlab > > > -- > Josef Smidrkal > > _______________________________________________ > Brmlab mailing list > Brmlab@brmlab.cz > https://brmlab.cz/cgi-bin/mailman/listinfo/brmlab >
_______________________________________________ Brmlab mailing list Brmlab@brmlab.cz https://brmlab.cz/cgi-bin/mailman/listinfo/brmlab