Hello,
I have installed OpenBSD current on a HP Compaq t5135 Thin Client.
I have changed the flash disk module from a 64mb to 1GB.
I have configured during installation no swap because I would change the
configuration to read only.
This is the dmesg from the Installation Shell:
OpenBSD 5.0-current (RAMDISK_CD) #11: Fri Oct 7 13:13:13 MDT 2011
[email protected]:/usr/src/sys/arch/i386/compile/RAMDISK_CD
cpu0: VIA Esther processor 400MHz ("CentaurHauls" 686-class) 400 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,CMOV,PAT,CFLUSH,ACPI,MM
X,FXSR,SSE,SSE2,TM,SBF,SSE3,EST,TM2
real mem = 116912128 (111MB)
avail mem = 108072960 (103MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 12/19/06, BIOS32 rev. 0 @ 0xfa350,
SMBIOS rev. 2.3 @ 0xf0000 (35 entries)
bios0: vendor Phoenix Technologies, LTD version "786R3 v1.00" date
12/19/2006
bios0: Hewlett-Packard hp t5000 series
apm0 at bios0: Power Management spec V1.2
acpi at bios0 function 0x0 not configured
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xdf44
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdea0/160 (8 entries)
pcibios0: bad IRQ table checksum
pcibios0: PCI BIOS has 8 Interrupt Routing table entries
pcibios0: PCI Exclusive IRQs: 5 10 11
pcibios0: PCI Interrupt Router at 000:17:0 ("VIA VT8237 ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0x8200 0xcc000/0x8000! 0xd4000/0x2000
cpu0 at mainbus0: (uniprocessor)
cpu0: RNG AES AES-CTR SHA1 SHA256 RSA
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "VIA CN700 Host" rev 0x00
pchb1 at pci0 dev 0 function 1 "VIA CN700 Host" rev 0x00
pchb2 at pci0 dev 0 function 2 "VIA CN700 Host" rev 0x00
pchb3 at pci0 dev 0 function 3 "VIA PT890 Host" rev 0x00
pchb4 at pci0 dev 0 function 4 "VIA CN700 Host" rev 0x00
pchb5 at pci0 dev 0 function 7 "VIA CN700 Host" rev 0x00
ppb0 at pci0 dev 1 function 0 "VIA VT8377 AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "VIA S3 Unichrome PRO IGP" rev 0x01
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
pciide0 at pci0 dev 15 function 0 "VIA VT82C571 IDE" rev 0x06: ATA133,
channel 0 configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: < 1024MB ATA Flash Disk>
wd0: 1-sector PIO, LBA, 977MB, 2001888 sectors
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2
pciide0: channel 1 ignored (disabled)
uhci0 at pci0 dev 16 function 0 "VIA VT83C572 USB" rev 0x81: irq 11
uhci1 at pci0 dev 16 function 1 "VIA VT83C572 USB" rev 0x81: irq 11
uhci2 at pci0 dev 16 function 2 "VIA VT83C572 USB" rev 0x81: irq 5
uhci3 at pci0 dev 16 function 3 "VIA VT83C572 USB" rev 0x81: irq 5
ehci0 at pci0 dev 16 function 4 "VIA VT6202 USB" rev 0x86: irq 10
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "VIA EHCI root hub" rev 2.00/1.00 addr 1
pcib0 at pci0 dev 17 function 0 "VIA VT8237 ISA" rev 0x00
"VIA VT8233 AC97" rev 0x60 at pci0 dev 17 function 5 not configured
vr0 at pci0 dev 18 function 0 "VIA RhineII-2" rev 0x78: irq 11, address
00:1a:4b:bd:4d:18
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 10: OUI
0x004063, model 0x0032
usb1 at uhci0: USB revision 1.0
uhub1 at usb1 "VIA UHCI root hub" rev 1.00/1.00 addr 1
usb2 at uhci1: USB revision 1.0
uhub2 at usb2 "VIA UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci2: USB revision 1.0
uhub3 at usb3 "VIA UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci3: USB revision 1.0
uhub4 at usb4 "VIA UHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
umass0 at uhub0 port 7 configuration 1 interface 0 "JMicron USB to ATA/ATAPI
Bridge" rev 2.00/1.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
cd0 at scsibus0 targ 1 lun 0: <TSSTcorp, CD/DVDW TS-H552U, US06> SCSI0
5/cdrom removable serial.152d2338222222222222
softraid0 at root
scsibus1 at softraid0: 256 targets
root on rd0a swap on rd0b dump on rd0b
boot output:
Using drive 0, partition 3
Loading....
Probing: pc0 com0 apm pci mem[639k 110M a20=on]
disk: hd0+
>> OpenBSD/i386 BOOT 3.17
boot>
booting hd0a:/bsd: 8197340+1088968 [61+368096+353709]=0x98b810
entry point at 0x200120
[using 722284 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2011 OpenBSD. All rights reserved. http://www.openbsd.org
kernel: page fault trap, code=0
Stopped at uvm_pmr_freepages+0xe9: mov1 0x38(%edi),%eax
uvm_pmr_freepages(d0c079fc,62ad,1a9ff0,62ad,62ad) at uvm_pmr_freepages+0xe9
uvm_page_init(d0b8df20,d0b8df1c,32b8df28,b8e0000,b8c000) at
uvm_page_init+0x1ab
uvm_init(d08aa080,d08ac4a0,c0,d0b8df4c,2) at uvm_init+0x30
main(d02004ba,d02004c2,0,0,0) at main+0x53
ddb> trace
uvm_pmr_freepages(d0c079fc,62ad,1a9ff0,62ad,62ad) at uvm_pmr_freepages+0xe9
uvm_page_init(d0b8df20,d0b8df1c,32b8df28,b8e0000,b8c000) at
uvm_page_init+0x1ab
uvm_init(d08aa080,d08ac4a0,c0,d0b8df4c,2) at uvm_init+0x30
main(d02004ba,d02004c2,0,0,0) at main+0x53
Thank you.
