Hello,
My Yeeloong 8101B has a QWERTY keyboard, but I've set /etc/kbdtype to "fr"
to have my usual French AZERTY layout. It works fine, except in the
installer. (I don't mind using QWERTY, but if there's my usual layout I'd
rather use it.)
If I boot bsd.rd, I'm asked for a keyboard layout (whether I'm choosing
to Install or Upgrade). But it has no effect: if I type "fr", I still
have the default QWERTY layout. Things work fine on my usual amd64/i386
systems when I do this.
If I go to the Shell
# kbd fr
has no effect
and
# kbd -l
returns nothing.
dmesg provided in [1].
Then, there's macppc, where bsd.rd never asks me for a keyboard layout
(I don't use an Apple keyboard, but an AZERTY PC keyboard).
In the Shell, the kbd command doesn't exist at all. Indeed, kbd is not
enabled in distrib/ for macppc.
dmesg provided in [2].
For macppc, this looks intentional (kbd works once the system is
installed). But for loongson, it looks like something is missing, or
kbd was enabled by mistake in the installer.
[1]:
[ using 310440 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2014 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 5.5 (RAMDISK) #100: Thu Feb 27 01:57:32 MST 2014
[email protected]:/usr/src/sys/arch/loongson/compile/RAMDISK
real mem = 1073741824 (1024MB)
avail mem = 1056931840 (1007MB)
mainbus0 at root: Lemote Yeeloong
cpu0 at mainbus0: STC Loongson2F CPU 796 MHz, STC Loongson2F FPU
cpu0: cache L1-I 64KB D 64KB 4 way, L2 512KB 4 way
bonito0 at mainbus0: memory and PCI-X controller, rev 1
pci0 at bonito0 bus 0
rl0 at pci0 dev 7 function 0 "Realtek 8139" rev 0x10: irq 5, address XXX
rlphy0 at rl0 phy 0: RTL internal PHY
smfb0 at pci0 dev 8 function 0 "Silicon Motion LynxEM+" rev 0xb0
wsdisplay0 at smfb0 mux 1: console (std, vt100 emulation)
ohci0 at pci0 dev 9 function 0 "NEC USB" rev 0x44: irq 7, version 1.0
ehci0 at pci0 dev 9 function 1 "NEC USB" rev 0x05: irq 7
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "NEC EHCI root hub" rev 2.00/1.00 addr 1
glxpcib0 at pci0 dev 14 function 0 "AMD CS5536 ISA" rev 0x03: rev 3, 32-bit
3579545Hz timer, watchdog, gpio, i2c
isa0 at glxpcib0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
mcclock0 at isa0 port 0x70/2: mc146818 or compatible
gpio at glxpcib0 not configured
iic at glxpcib0 not configured
pciide0 at pci0 dev 14 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <ST9160310AS>
wd0: 16-sector PIO, LBA48, 152627MB, 312581808 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 ignored (disabled)
"AMD CS5536 Audio" rev 0x01 at pci0 dev 14 function 3 not configured
ohci1 at pci0 dev 14 function 4 "AMD CS5536 USB" rev 0x02: isa irq 11, version
1.0, legacy support
ehci1 at pci0 dev 14 function 5 "AMD CS5536 USB" rev 0x02: isa irq 11
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "AMD EHCI root hub" rev 2.00/1.00 addr 1
usb2 at ohci0: USB revision 1.0
uhub2 at usb2 "NEC OHCI root hub" rev 1.00/1.00 addr 1
usb3 at ohci1: USB revision 1.0
uhub3 at usb3 "AMD OHCI root hub" rev 1.00/1.00 addr 1
clock0 at mainbus0: int 5
umass0 at uhub1 port 1 configuration 1 interface 0 "Generic USB2.0-CRW" rev
2.00/58.87 addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <Generic-, Multi-Card, 1.00> SCSI0 0/direct
removable serial.0bda0158114173400000
urtw0 at uhub1 port 4 "Realtek RTL8187B" rev 2.00/2.00 addr 3
urtw0: RTL8187B rev E, address XXX
pmon bootpath: /dev/disk/wd0
boot device: wd0
root on rd0a swap on rd0b dump on rd0b
[2]:
[ using 305336 bytes of bsd ELF symbol table ]
console out [ATY,Rage128y]console in [keyboard] USB and ADB found, using ADB
: memaddr 88000000 size 8000000, : consaddr 88000000, : ioaddr 80920000, size
20000: width 640 linebytes 640 height 480 depth 8
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2014 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 5.5 (RAMDISK) #150: Thu Feb 27 23:57:58 MST 2014
[email protected]:/usr/src/sys/arch/macppc/compile/RAMDISK
real mem = 536870912 (512MB)
avail mem = 509181952 (485MB)
warning: no entropy supplied by boot loader
mainbus0 at root: model PowerMac1,1
cpu0 at mainbus0: 750 (Revision 0x202): 350 MHz: 1MB backside cache
mem at mainbus0 not configured
mpcpcibr0 at mainbus0 pci: grackle
pci0 at mpcpcibr0 bus 0
ppb0 at pci0 dev 13 function 0 "DEC 21154" rev 0x02
pci1 at ppb0 bus 1
macobio0 at pci1 dev 5 function 0 "Apple Paddington" rev 0x00
macintr0 at macobio0 offset 0x10
mesh0 at macobio0 offset 0x10000 irq 12: 50MHz
scsibus0 at mesh0: 8 targets, initiator 7
"escc-legacy" at macobio0 offset 0x12000 not configured
zsc0 at macobio0 offset 0x13000: irq 15,16
zstty0 at zsc0 channel 0
zstty1 at zsc0 channel 1
"davbus" at macobio0 offset 0x14000 not configured
"power-mgt" at macobio0 offset 0x0 not configured
"fdc" at macobio0 offset 0x15000 not configured
adb0 at macobio0 offset 0x16000: irq 18, via-cuda, 0 targets
wdc0 at macobio0 offset 0x20000 irq 13: DMA
atapiscsi0 at wdc0 channel 0 drive 0
scsibus1 at atapiscsi0: 2 targets
cd0 at scsibus1 targ 0 lun 0: <GoldStar, CD-ROM CRD-8322B, 1.02> ATAPI 5/cdrom
removable
cd0(wdc0:0:0): using BIOS timings, DMA mode 2
bm0 at macobio0 offset 0x11000 irq 42,33: address XXX
lxtphy0 at bm0 phy 0: LXT970 10/100 PHY, rev. 1
"nvram" at macobio0 offset 0x60000 not configured
"TI TSB12LV21 FireWire" rev 0x02 at pci1 dev 0 function 0 not configured
pciide0 at pci1 dev 1 function 0 "CMD Technology PCI0646" rev 0x05: DMA,
channel 0 configured to native-PCI, channel 1 configured to native-PCI
pciide0: using irq 26 for native-PCI interrupt
wd0 at pciide0 channel 0 drive 0: <ST380011A>
wd0: 16-sector PIO, LBA48, 76319MB, 156301488 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 ignored (disabled)
ahc0 at pci1 dev 2 function 0 "Adaptec AIC-7850" rev 0x03: irq 23
scsibus2 at ahc0: 8 targets, initiator 7
ohci0 at pci1 dev 6 function 0 "Opti 82C861" rev 0x10: irq 28, version 1.0,
legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0 "Opti OHCI root hub" rev 1.00/1.00 addr 1
vgafb0 at pci0 dev 16 function 0 "ATI Rage 128" rev 0x00, mmio
wsdisplay0 at vgafb0 mux 1: console (std, vt100 emulation)
uhidev0 at uhub0 port 2 configuration 1 interface 0 "vendor 0x04f3 product
0x0103" rev 1.10/1.07 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0
wskbd0 at ukbd0 mux 1
wskbd0: connecting to wsdisplay0
uhidev1 at uhub0 port 2 configuration 1 interface 1 "vendor 0x04f3 product
0x0103" rev 1.10/1.07 addr 2
uhidev1: iclass 3/0, 2 report ids
uhid0 at uhidev1 reportid 1: input=2, output=0, feature=0
uhid1 at uhidev1 reportid 2: input=1, output=0, feature=0
softraid0 at root
scsibus3 at softraid0: 256 targets
bootpath: /pci/@d/pci-ata@1/ata-4@0/disk@0:/nbsd.rd
root on rd0a swap on rd0b dump on rd0b
