Synopsis: named exits due to assertion failure
Category: system
Environment:
System : OpenBSD 5.5
Details : OpenBSD 5.5 (GENERIC) #0: Fri Apr 25 15:04:32 CEST 2014
[email protected]:/binpatchng/work-binpatch55-i386/src/sys/arch/i386/compile/GENERIC
Architecture: OpenBSD.i386
Machine : i386
Description:
named (BIND 9.4.2-P2 from OpenBSD 5.5) suddenly exited with
the following syslog messages:
Jun 19 14:56:01 myhost named[11992]:
/usr/src/usr.sbin/bind/lib/dns/adb.c:3392: REQUIRE((((addr) != ((void
*)0)) && (((const isc__magic_t *)(addr))->magic == ((('a') << 24 |
('d') << 16 | ('A') << 8 | ('I')))))) failed
Jun 19 14:56:01 myhost named[11992]: exiting (due to assertion failure)
How-To-Repeat:
I don't know.
Fix:
I don't know.
Regards
Andy
SENDBUG: Run sendbug as root if this is an ACPI report!
SENDBUG: dmesg and usbdevs are attached.
SENDBUG: Feel free to delete or use the -D flag if they contain
sensitive information.
dmesg:
OpenBSD 5.5 (GENERIC) #0: Fri Apr 25 15:04:32 CEST 2014
[email protected]:/binpatchng/work-binpatch55-i386/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD"
586-class) 499 MHz
cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX,MMXX,3DNOW2,3DNOW
real mem = 267943936 (255MB)
avail mem = 251260928 (239MB)
warning: no entropy supplied by boot loader
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 01/27/08, BIOS32 rev. 0 @ 0xfceb2
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xe0000/0xa800
cpu0 at mainbus0: (uniprocessor)
mtrr: K6-family MTRR support (2 registers)
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x33
glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES
vr0 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 10,
address 00:0d:b9:13:66:3c
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x004063, model 0x0034
glxpcib0 at pci0 dev 15 function 0 "AMD CS5536 ISA" rev 0x03: rev 3,
32-bit 3579545Hz timer, watchdog, gpio, i2c
gpio0 at glxpcib0: 32 pins
iic0 at glxpcib0
maxtmp0 at iic0 addr 0x4c: lm86
pciide0 at pci0 dev 15 function 2 "AMD CS5536 IDE" rev 0x01: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <>
wd0: 1-sector PIO, LBA, 3882MB, 7952112 sectors
wd0(pciide0:0:0): using PIO mode 4
pciide0: channel 1 ignored (disabled)
ohci0 at pci0 dev 15 function 4 "AMD CS5536 USB" rev 0x02: irq 15,
version 1.0, legacy support
ehci0 at pci0 dev 15 function 5 "AMD CS5536 USB" rev 0x02: irq 15
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "AMD EHCI root hub" rev 2.00/1.00 addr 1
isa0 at glxpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "AMD OHCI root hub" rev 1.00/1.00 addr 1
nvram: invalid checksum
vscsi0 at root
scsibus0 at vscsi0: 256 targets
softraid0 at root
scsibus1 at softraid0: 256 targets
root on wd0a (f8be99b5860f18bf.a) swap on wd0b dump on wd0b
clock: unknown CMOS layout
usbdevs:
Controller /dev/usb0:
addr 1: high speed, self powered, config 1, EHCI root hub(0x0000),
AMD(0x1022), rev 1.00
port 1 powered
port 2 powered
port 3 powered
port 4 powered
Controller /dev/usb1:
addr 1: full speed, self powered, config 1, OHCI root hub(0x0000),
AMD(0x1022), rev 1.00
port 1 powered
port 2 powered
port 3 powered
port 4 powered
