Mark Kettenis <mark.kettenis <at> xs4all.nl> writes:
>
> > Date: Sun, 19 Oct 2014 17:59:29 +0200
> > From: Julien Dehaese <jdehaese <at> gmail.com>
> >
> > Hi,
> > I'm trying to get openbsd running on an Intel Baytrail motherboard with
a
> > SSD disk.
> >
> > Motherboard is Asrock Q1900-ITX, 4GB RAM
> > Kingston SSD model : SV300S37A60G
> >
> > Steps to reproduce:
> > - performed standard install of openbsd 5.6-current (19/10/2014) -
today.
> > All went well during the install until the first reboot after install.
> > - during the first reboot after install, openbsd raises a panic :
> > lapic_set_lvt
> > - ran the trace and ps when debugger prompt appeared.
> >
> > Same error occurs at each reboot.
>
> Does a GENERIC (non-MP) kernel boot on the machine? The installer
> should have installed one as bsd.sp, which you can specify at the
> boot> prompt.
>
> If that kernel boots, can you send use acpidump(8) output for this
machine?
>
> Thanks,
>
> Mark
>
>
Hi,
I will step in here as I'm having the same problems with the same
mainboard.
There are four different scenarios - three of which being erroneous:
1. disable USB (in UEFI), boot bsd.sp:
-> This setup works fine
2. disable USB, boot bsd:
-> I'm getting a kernel panic:
panic: lapic_set_lvt: bad pin value 171
I entered 'trace', 'ps', 'mach ddbcpu 1', 'trace', 'mach ddbcpu 2',
'trace', 'mach ddbcpu 3'. The last command did never return.
3. enable USB in legacy mode (but disable USB 3.0), boot bsd.sp:
-> The boot process takes very long time. Eight times the console shows the
following message:
ehci_sync_hc: tsleep() = 35
4. enable USB in legacy mode, boot bsd:
-> The boot process never finishes (without a kernel panic). The last
message shown is:
ehci_sync_hc: tsleep() = 35
These are the corresponding logs:
(1)
>> OpenBSD/amd64 BOOT 3.28
boot>
\|/-\|/booting hd0a:/bsd.sp:
entry point at 0x10001e0 [7205c766, 34000004, 24448b12, dba0a304]
[ using 923720 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2014 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 5.6 (GENERIC) #310: Fri Aug 8 00:14:24 MDT 2014
[email protected]:/usr/src/sys/arch/amd64/compile/GENERIC
real mem = 4166979584 (3973MB)
avail mem = 4047314944 (3859MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.8 @ 0xebd30 (18 entries)
bios0: vendor American Megatrends Inc. version "P1.70" date 11/04/2014
bios0: ASRock Q1900B-ITX
acpi0 at bios0: rev 2
acpi0: sleep states S0 S3 S4 S5
acpi0: tables DSDT FACP APIC FPDT MCFG LPIT AAFT HPET SSDT SSDT SSDT UEFI
acpi0: wakeup devices PS2K(S4) PS2M(S4) UAR1(S4) UAR2(S4) XHC1(S4) EHC1(S4)
PXSX(S4) PXSX(S4) PXSX(S4) PXSX(S4) PWRB(S0) BRCM(S0) BRC3(S0)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 2000.45 MHz
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFL
USH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-
CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RD
RAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS
cpu0: 1MB 64b/line 16-way L2 cache
cpu0: smt 0, core 0, package 0
mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
cpu0: apic clock running at 83MHz
cpu at mainbus0: not configured
cpu at mainbus0: not configured
cpu at mainbus0: not configured
ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 87 pins
acpimadt0: bogus nmi for apid 0
acpimadt0: bogus nmi for apid 2
acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (RP01)
acpiprt2 at acpi0: bus 2 (RP02)
acpiprt3 at acpi0: bus 3 (RP03)
acpiprt4 at acpi0: bus 4 (RP04)
acpiec0 at acpi0: not present
acpicpu0 at acpi0: C1, PSS
acpipwrres0 at acpi0: PLPE
acpipwrres1 at acpi0: PLPE
acpipwrres2 at acpi0: USBC, resource for EHC1, OTG1
acpipwrres3 at acpi0: CLK0, resource for CAM1
acpipwrres4 at acpi0: CLK1, resource for CAM0, CAM2
acpipwrres5 at acpi0: FN00, resource for FAN0
acpitz0 at acpi0: critical temperature is 90 degC
acpibat0 at acpi0: BAT0 not present
acpibat1 at acpi0: BAT1 not present
acpibat2 at acpi0: BAT2 not present
acpibtn0 at acpi0: LID0
acpibtn1 at acpi0: PWRB
acpibtn2 at acpi0: SLPB
acpivideo0 at acpi0: GFX0
acpivout0 at acpivideo0: DD1F
cpu0: Enhanced SpeedStep 2000 MHz: speeds: 1993, 1992, 1909, 1826, 1743,
1660, 1577, 1494, 1411, 1328 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 vendor "Intel", unknown product 0x0f00 rev
0x0c
vga1 at pci0 dev 2 function 0 vendor "Intel", unknown product 0x0f31 rev
0x0c
intagp at vga1 not configured
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ahci0 at pci0 dev 19 function 0 vendor "Intel", unknown product 0x0f23 rev
0x0c: msi, AHCI 1.3
scsibus1 at ahci0: 32 targets
sd0 at scsibus1 targ 0 lun 0: <ATA, WDC WD20NPVX-00E, 01.0> SCSI3 0/direct
fixed naa.50014ee260103503
sd0: 1907729MB, 512 bytes/sector, 3907029168 sectors
sd1 at scsibus1 targ 1 lun 0: <ATA, WDC WD20NPVX-00E, 01.0> SCSI3 0/direct
fixed naa.50014ee2b6060356
sd1: 1907729MB, 512 bytes/sector, 3907029168 sectors
vendor "Intel", unknown product 0x0f18 (class crypto subclass
miscellaneous, rev 0x0c) at pci0 dev 26 function 0 not configured
ppb0 at pci0 dev 28 function 0 vendor "Intel", unknown product 0x0f48 rev
0x0c: msi
pci1 at ppb0 bus 1
ppb1 at pci0 dev 28 function 1 vendor "Intel", unknown product 0x0f4a rev
0x0c: msi
pci2 at ppb1 bus 2
re0 at pci2 dev 0 function 0 "Realtek 8168" rev 0x11: RTL8168G/8111G
(0x4c00), msi, address d0:50:99:2b:e9:e0
rgephy0 at re0 phy 7: RTL8251 PHY, rev. 0
ppb2 at pci0 dev 28 function 2 vendor "Intel", unknown product 0x0f4c rev
0x0c: msi
pci3 at ppb2 bus 3
ppb3 at pci0 dev 28 function 3 vendor "Intel", unknown product 0x0f4e rev
0x0c: msi
pci4 at ppb3 bus 4
pcib0 at pci0 dev 31 function 0 vendor "Intel", unknown product 0x0f1c rev
0x0c
vendor "Intel", unknown product 0x0f12 (class serial bus subclass SMBus,
rev 0x0c) at pci0 dev 31 function 3 not configured
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
wbsio0 at isa0 port 0x2e/2: NCT6776F rev 0x33
lm1 at wbsio0 port 0x290/8: NCT6776F
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
sd2 at scsibus3 targ 1 lun 0: <OPENBSD, SR RAID 1, 005> SCSI2 0/direct
fixed
sd2: 102398MB, 512 bytes/sector, 209712004 sectors
root on sd0a (c22964f6db284666.a) swap on sd0b dump on sd0b
swapctl: adding 988cea2ce46be646.b as swap device at priority 0
Automatic boot in progress: starting file system checks.
/dev/sd0a (c22964f6db284666.a): file system is clean; not checking
/dev/sd0g (c22964f6db284666.g): file system is clean; not checking
/dev/sd0d (c22964f6db284666.d): file system is clean; not checking
/dev/sd2a (07f0d484f3d87f1c.a): file system is clean; not checking
/dev/sd1a (988cea2ce46be646.a): file system is clean; not checking
/dev/sd0e (c22964f6db284666.e): file system is clean; not checking
/dev/sd0f (c22964f6db284666.f): file system is clean; not checking
/dev/sd1e (988cea2ce46be646.e): file system is clean; not checking
/dev/sd1f (988cea2ce46be646.f): file system is clean; not checking
/dev/sd1g (988cea2ce46be646.g): file system is clean; not checking
/dev/sd1d (988cea2ce46be646.d): file system is clean; not checking
setting tty flags
pf enabled
starting network
DHCPREQUEST on re0 to 255.255.255.255
DHCPACK from 192.168.1.1 (30:85:a9:69:f3:ff)
bound to 192.168.1.214 -- renewal in 43200 seconds.
starting early daemons: syslogd pflogd ntpd.
starting RPC daemons:.
savecore: no core dump
checking quotas: done.
clearing /tmp
kern.securelevel: 0 -> 1
creating runtime link editor directory cache.
preserving editor files.
starting network daemons: sshd smtpd sndiod.
starting local daemons: cron.
Mon Feb 2 21:26:01 CET 2015
(2)
>> OpenBSD/amd64 BOOT 3.28
boot> log boot /bsd
\|/-\|/booting hd0a:/bsd:
entry point at 0x10001e0 [7205c766, 34000004, 24448b12, 6ba0a304]
[ using 927424 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2014 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 5.6 (GENERIC.MP) #333: Fri Aug 8 00:20:21 MDT 2014
[email protected]:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 4166979584 (3973MB)
avail mem = 4047269888 (3859MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.8 @ 0xebd30 (18 entries)
bios0: vendor American Megatrends Inc. version "P1.70" date 11/04/2014
bios0: ASRock Q1900B-ITX
acpi0 at bios0: rev 2
acpi0: sleep states S0 S3 S4 S5
acpi0: tables DSDT FACP APIC FPDT MCFG LPIT AAFT HPET SSDT SSDT SSDT UEFI
acpi0: wakeup devices PS2K(S4) PS2M(S4) UAR1(S4) UAR2(S4) XHC1(S4) EHC1(S4)
PXSX(S4) PXSX(S4) PXSX(S4) PXSX(S4) PWRB(S0) BRCM(S0) BRC3(S0)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 2000.45 MHz
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFL
USH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-
CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RD
RAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS
cpu0: 1MB 64b/line 16-way L2 cache
cpu0: smt 0, core 0, package 0
mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
cpu0: apic clock running at 83MHz
cpu0: mwait min=64, max=64, C-substates=0.2.0.0.0, IBE
cpu1 at mainbus0: apid 2 (application processor)
cpu1: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 2000.01 MHz
cpu1:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFL
USH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-
CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RD
RAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS
cpu1: 1MB 64b/line 16-way L2 cache
cpu1: smt 0, core 1, package 0
cpu2 at mainbus0: apid 4 (application processor)
cpu2: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 2000.01 MHz
cpu2:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFL
USH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-
CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RD
RAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS
cpu2: 1MB 64b/line 16-way L2 cache
cpu2: smt 0, core 2, package 0
cpu3 at mainbus0: apid 6 (application processor)
cpu3: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 2000.01 MHz
cpu3:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFL
USH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-
CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RD
RAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS
cpu3: 1MB 64b/line 16-way L2 cache
cpu3: smt 0, core 3, package 0
ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 87 pins
acpimadt0: bogus nmi for apid 0
acpimadt0: bogus nmi for apid 2
acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (RP01)
acpiprt2 at acpi0: bus 2 (RP02)
acpiprt3 at acpi0: bus 3 (RP03)
acpiprt4 at acpi0: bus 4 (RP04)
acpiec0 at acpi0: not present
acpicpu0 at acpi0: C1, PSS
acpicpu1 at acpi0: C1, PSS
acpicpu2 at acpi0: C1, PSS
acpicpu3 at acpi0: C1, PSS
acpipwrres0 at acpi0: PLPE
acpipwrres1 at acpi0: PLPE
acpipwrres2 at acpi0: USBC, resource for EHC1, OTG1
acpipwrres3 at acpi0: CLK0, resource for CAM1
acpipwrres4 at acpi0: CLK1, resource for CAM0, CAM2
acpipwrres5 at acpi0: FN00, resource for FAN0
acpitz0 at acpi0: critical temperature is 90 degC
acpibat0 at acpi0: BAT0 not present
acpibat1 at acpi0: BAT1 not present
acpibat2 at acpi0: BAT2 not present
acpibtn0 at acpi0: LID0
acpibtn1 at acpi0: PWRB
acpibtn2 at acpi0: SLPB
acpivideo0 at acpi0: GFX0
acpivout0 at acpivideo0: DD1F
cpu0: Enhanced SpeedStep 2000 MHz: speeds: 1993, 1992, 1909, 1826, 1743,
1660, 1577, 1494, 1411, 1328 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 vendor "Intel", unknown product 0x0f00 rev
0x0c
vga1 at pci0 dev 2 function 0 vendor "Intel", unknown product 0x0f31 rev
0x0c
intagp at vga1 not configured
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ahci0 at pci0 dev 19 function 0 vendor "Intel", unknown product 0x0f23 rev
0x0c: msi, AHCI 1.3
scsibus1 at ahci0: 32 targets
sd0 at scsibus1 targ 0 lun 0: <ATA, WDC WD20NPVX-00E, 01.0> SCSI3 0/direct
fixed naa.50014ee260103503
sd0: 1907729MB, 512 bytes/sector, 3907029168 sectors
sd1 at scsibus1 targ 1 lun 0: <ATA, WDC WD20NPVX-00E, 01.0> SCSI3 0/direct
fixed naa.50014ee2b6060356
sd1: 1907729MB, 512 bytes/sector, 3907029168 sectors
vendor "Intel", unknown product 0x0f18 (class crypto subclass
miscellaneous, rev 0x0c) at pci0 dev 26 function 0 not configured
ppb0 at pci0 dev 28 function 0 vendor "Intel", unknown product 0x0f48 rev
0x0c: msi
pci1 at ppb0 bus 1
ppb1 at pci0 dev 28 function 1 vendor "Intel", unknown product 0x0f4a rev
0x0c: msi
pci2 at ppb1 bus 2
re0 at pci2 dev 0 function 0 "Realtek 8168" rev 0x11: RTL8168G/8111G
(0x4c00), msi, address d0:50:99:2b:e9:e0
rgephy0 at re0 phy 7: RTL8251 PHY, rev. 0
ppb2 at pci0 dev 28 function 2 vendor "Intel", unknown product 0x0f4c rev
0x0c: msi
pci3 at ppb2 bus 3
ppb3 at pci0 dev 28 function 3 vendor "Intel", unknown product 0x0f4e rev
0x0c: msi
pci4 at ppb3 bus 4
pcib0 at pci0 dev 31 function 0 vendor "Intel", unknown product 0x0f1c rev
0x0c
vendor "Intel", unknown product 0x0f12 (class serial bus subclass SMBus,
rev 0x0c) at pci0 dev 31 function 3 not configured
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
wbsio0 at isa0 port 0x2e/2: NCT6776F rev 0x33
lm1 at wbsio0 port 0x290/8: NCT6776F
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
sd2 at scsibus3 targ 1 lun 0: <OPENBSD, SR RAID 1, 005> SCSI2 0/direct
fixed
sd2: 102398MB, 512 bytes/sector, 209712004 sectors
root on sd0a (c22964f6db284666.a) swap on sd0b dump on sd0b
panic: lapic_set_lvt: bad pin value 171
Stopped at Debugger+0x9: leave
RUN AT LEAST 'trace' AND 'ps' AND INCLUDE OUTPUT WHEN REPORTING THIS PANIC!
IF RUNNING SMP, USE 'mach ddbcpu <#>' AND 'trace' ON OTHER PROCESSORS, TOO.
DO NOT EVEN BOTHER REPORTING THIS WITHOUT INCLUDING THAT INFORMATION!
ddb{2}> trace
Debugger() at Debugger+0x9
panic() at panic+0xfe
lapic_set_lvt() at lapic_set_lvt+0x216
cpu_hatch() at cpu_hatch+0xc6
cpu_spinup_trampoline_end() at cpu_spinup_trampoline_end+0x67
end trace frame: 0x0, count: -5
ddb{2}> ps
PID PPID PGRP UID S FLAGS WAIT COMMAND
18355 0 0 0 2 0x14200 aiodoned
17129 0 0 0 2 0x14200 update
8282 0 0 0 2 0x14200 cleaner
6134 0 0 0 7 0x14200 reaper
7238 0 0 0 2 0x14200 pagedaemon
4928 0 0 0 3 0x14200 bored srdis
22073 0 0 0 3 0x14200 bored crypto
547 0 0 0 3 0x14200 pftm pfpurge
430 0 0 0 3 0x40014200 acpi0 acpi0
21391 0 0 0 1 0x14200 idle3
22360 0 0 0 1 0x14200 idle2
26074 0 0 0 1 0x14200 idle1
28857 0 0 0 3 0x14200 bored sensors
2230 0 0 0 3 0x14200 bored systqmp
26826 0 0 0 3 0x14200 bored systq
8751 0 0 0 3 0x14200 bored syswq
10188 0 0 0 3 0x40014200 idle0
1 0 0 0 3 0 initexec swapper
0 -1 0 0 7 0x10200 swapper
ddb{2}> mach ddbcpu 1
Stopped at Debugger+0x9: leave
RUN AT LEAST 'trace' AND 'ps' AND INCLUDE OUTPUT WHEN REPORTING THIS PANIC!
IF RUNNING SMP, USE 'mach ddbcpu <#>' AND 'trace' ON OTHER PROCESSORS, TOO.
DO NOT EVEN BOTHER REPORTING THIS WITHOUT INCLUDING THAT INFORMATION!
ddb{1}> trace
Debugger() at Debugger+0x9
x86_ipi_handler() at x86_ipi_handler+0x64
Xresume_lapic_ipi() at Xresume_lapic_ipi+0x1b
--- interrupt ---
Bad frame pointer: 0xffff800022156f10
end trace frame: 0xffff800022156f10, count: -3
__mp_lock+0x48:
ddb{1}> [A[A mach ddbcpu 2
Stopped at Debugger+0x9: leave
RUN AT LEAST 'trace' AND 'ps' AND INCLUDE OUTPUT WHEN REPORTING THIS PANIC!
IF RUNNING SMP, USE 'mach ddbcpu <#>' AND 'trace' ON OTHER PROCESSORS, TOO.
DO NOT EVEN BOTHER REPORTING THIS WITHOUT INCLUDING THAT INFORMATION!
ddb{2}> trace
Debugger() at Debugger+0x9
panic() at panic+0xfe
lapic_set_lvt() at lapic_set_lvt+0x216
cpu_hatch() at cpu_hatch+0xc6
cpu_spinup_trampoline_end() at cpu_spinup_trampoline_end+0x67
end trace frame: 0x0, count: -5
ddb{2}> mach ddbcpu 3
(3)
>> OpenBSD/amd64 BOOT 3.28
boot>
\|/-\|/booting hd0a:/bsd.sp:
entry point at 0x10001e0 [7205c766, 34000004, 24448b12, dba0a304]
[ using 923720 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2014 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 5.6 (GENERIC) #310: Fri Aug 8 00:14:24 MDT 2014
[email protected]:/usr/src/sys/arch/amd64/compile/GENERIC
real mem = 4166979584 (3973MB)
avail mem = 4047314944 (3859MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.8 @ 0xebd30 (18 entries)
bios0: vendor American Megatrends Inc. version "P1.70" date 11/04/2014
bios0: ASRock Q1900B-ITX
acpi0 at bios0: rev 2
acpi0: sleep states S0 S3 S4 S5
acpi0: tables DSDT FACP APIC FPDT MCFG LPIT AAFT HPET SSDT SSDT SSDT UEFI
acpi0: wakeup devices PS2K(S4) PS2M(S4) UAR1(S4) UAR2(S4) XHC1(S4) EHC1(S4)
PXSX(S4) PXSX(S4) PXSX(S4) PXSX(S4) PWRB(S0) BRCM(S0) BRC3(S0)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 2000.45 MHz
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFL
USH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-
CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RD
RAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS
cpu0: 1MB 64b/line 16-way L2 cache
cpu0: smt 0, core 0, package 0
mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
cpu0: apic clock running at 83MHz
cpu at mainbus0: not configured
cpu at mainbus0: not configured
cpu at mainbus0: not configured
ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 87 pins
acpimadt0: bogus nmi for apid 0
acpimadt0: bogus nmi for apid 2
acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (RP01)
acpiprt2 at acpi0: bus 2 (RP02)
acpiprt3 at acpi0: bus 3 (RP03)
acpiprt4 at acpi0: bus 4 (RP04)
acpiec0 at acpi0: not present
acpicpu0 at acpi0: C1, PSS
acpipwrres0 at acpi0: PLPE
acpipwrres1 at acpi0: PLPE
acpipwrres2 at acpi0: USBC, resource for EHC1, OTG1
acpipwrres3 at acpi0: CLK0, resource for CAM1
acpipwrres4 at acpi0: CLK1, resource for CAM0, CAM2
acpipwrres5 at acpi0: FN00, resource for FAN0
acpitz0 at acpi0: critical temperature is 90 degC
acpibat0 at acpi0: BAT0 not present
acpibat1 at acpi0: BAT1 not present
acpibat2 at acpi0: BAT2 not present
acpibtn0 at acpi0: LID0
acpibtn1 at acpi0: PWRB
acpibtn2 at acpi0: SLPB
acpivideo0 at acpi0: GFX0
acpivout0 at acpivideo0: DD1F
cpu0: Enhanced SpeedStep 2000 MHz: speeds: 1993, 1992, 1909, 1826, 1743,
1660, 1577, 1494, 1411, 1328 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 vendor "Intel", unknown product 0x0f00 rev
0x0c
vga1 at pci0 dev 2 function 0 vendor "Intel", unknown product 0x0f31 rev
0x0c
intagp at vga1 not configured
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ahci0 at pci0 dev 19 function 0 vendor "Intel", unknown product 0x0f23 rev
0x0c: msi, AHCI 1.3
scsibus1 at ahci0: 32 targets
sd0 at scsibus1 targ 0 lun 0: <ATA, WDC WD20NPVX-00E, 01.0> SCSI3 0/direct
fixed naa.50014ee260103503
sd0: 1907729MB, 512 bytes/sector, 3907029168 sectors
sd1 at scsibus1 targ 1 lun 0: <ATA, WDC WD20NPVX-00E, 01.0> SCSI3 0/direct
fixed naa.50014ee2b6060356
sd1: 1907729MB, 512 bytes/sector, 3907029168 sectors
vendor "Intel", unknown product 0x0f18 (class crypto subclass
miscellaneous, rev 0x0c) at pci0 dev 26 function 0 not configured
ppb0 at pci0 dev 28 function 0 vendor "Intel", unknown product 0x0f48 rev
0x0c: msi
pci1 at ppb0 bus 1
ppb1 at pci0 dev 28 function 1 vendor "Intel", unknown product 0x0f4a rev
0x0c: msi
pci2 at ppb1 bus 2
re0 at pci2 dev 0 function 0 "Realtek 8168" rev 0x11: RTL8168G/8111G
(0x4c00), msi, address d0:50:99:2b:e9:e0
rgephy0 at re0 phy 7: RTL8251 PHY, rev. 0
ppb2 at pci0 dev 28 function 2 vendor "Intel", unknown product 0x0f4c rev
0x0c: msi
pci3 at ppb2 bus 3
ppb3 at pci0 dev 28 function 3 vendor "Intel", unknown product 0x0f4e rev
0x0c: msi
pci4 at ppb3 bus 4
ehci0 at pci0 dev 29 function 0 vendor "Intel", unknown product 0x0f34 rev
0x0c: apic 1 int 23
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
pcib0 at pci0 dev 31 function 0 vendor "Intel", unknown product 0x0f1c rev
0x0c
vendor "Intel", unknown product 0x0f12 (class serial bus subclass SMBus,
rev 0x0c) at pci0 dev 31 function 3 not configured
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
wbsio0 at isa0 port 0x2e/2: NCT6776F rev 0x33
lm1 at wbsio0 port 0x290/8: NCT6776F
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
uhub0: device problem, disabling port 1
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
softraid0: sd2 was not shutdown properly
sd2 at scsibus3 targ 1 lun 0: <OPENBSD, SR RAID 1, 005> SCSI2 0/direct
fixed
sd2: 102398MB, 512 bytes/sector, 209712004 sectors
root on sd0a (c22964f6db284666.a) swap on sd0b dump on sd0b
swapctl: adding 988cea2ce46be646.b as swap device at priority 0
Automatic boot in progress: starting file system checks.
/dev/sd0a (c22964f6db284666.a): file system is clean; not checking
/dev/sd0g (c22964f6db284666.g): file system is clean; not checking
/dev/sd1a (988cea2ce46be646.a): file system is clean; not checking
/dev/sd2a (07f0d484f3d87f1c.a): file system is clean; not checking
/dev/sd0d (c22964f6db284666.d): file system is clean; not checking
/dev/sd0e (c22964f6db284666.e): file system is clean; not checking
/dev/sd1e (988cea2ce46be646.e): file system is clean; not checking
/dev/sd0f (c22964f6db284666.f): file system is clean; not checking
/dev/sd1f (988cea2ce46be646.f): file system is clean; not checking
/dev/sd1g (988cea2ce46be646.g): file system is clean; not checking
/dev/sd1d (988cea2ce46be646.d): file system is clean; not checking
setting tty flags
pf enabled
starting network
DHCPREQUEST on re0 to 255.255.255.255
DHCPACK from 192.168.1.1 (30:85:a9:69:f3:ff)
bound to 192.168.1.214 -- renewal in 43200 seconds.
starting early daemons: syslogd pflogd ntpd.
starting RPC daemons:.
savecore: no core dump
checking quotas: done.
clearing /tmp
kern.securelevel: 0 -> 1
creating runtime link editor directory cache.
preserving editor files.
starting network daemons: sshd smtpd sndiod.
starting local daemons: cron.
Mon Feb 2 21:46:53 CET 2015
(4)
>> OpenBSD/amd64 BOOT 3.28
boot> boot /bsd
entry point at 0x10001e0 [7205c766, 34000004, 24448b12, 6ba0a304]
[ using 927424 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2014 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 5.6 (GENERIC.MP) #333: Fri Aug 8 00:20:21 MDT 2014
[email protected]:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 4166979584 (3973MB)
avail mem = 4047269888 (3859MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.8 @ 0xebd30 (18 entries)
bios0: vendor American Megatrends Inc. version "P1.70" date 11/04/2014
bios0: ASRock Q1900B-ITX
acpi0 at bios0: rev 2
acpi0: sleep states S0 S3 S4 S5
acpi0: tables DSDT FACP APIC FPDT MCFG LPIT AAFT HPET SSDT SSDT SSDT UEFI
acpi0: wakeup devices PS2K(S4) PS2M(S4) UAR1(S4) UAR2(S4) XHC1(S4) EHC1(S4)
PXSX(S4) PXSX(S4) PXSX(S4) PXSX(S4) PWRB(S0) BRCM(S0) BRC3(S0)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 2000.45 MHz
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFL
USH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-
CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RD
RAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS
cpu0: 1MB 64b/line 16-way L2 cache
cpu0: smt 0, core 0, package 0
mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
cpu0: apic clock running at 83MHz
cpu0: mwait min=64, max=64, C-substates=0.2.0.0.0, IBE
cpu1 at mainbus0: apid 2 (application processor)
cpu1: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 1999.99 MHz
cpu1:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFL
USH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-
CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RD
RAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS
cpu1: 1MB 64b/line 16-way L2 cache
cpu1: smt 0, core 1, package 0
cpu2 at mainbus0: apid 4 (application processor)
cpu2: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 1999.99 MHz
cpu2:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFL
USH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-
CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RD
RAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS
cpu2: 1MB 64b/line 16-way L2 cache
cpu2: smt 0, core 2, package 0
cpu3 at mainbus0: apid 6 (application processor)
cpu3: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 1999.99 MHz
cpu3:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFL
USH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-
CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RD
RAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS
cpu3: 1MB 64b/line 16-way L2 cache
cpu3: smt 0, core 3, package 0
ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 87 pins
acpimadt0: bogus nmi for apid 0
acpimadt0: bogus nmi for apid 2
acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (RP01)
acpiprt2 at acpi0: bus 2 (RP02)
acpiprt3 at acpi0: bus 3 (RP03)
acpiprt4 at acpi0: bus 4 (RP04)
acpiec0 at acpi0: not present
acpicpu0 at acpi0: C1, PSS
acpicpu1 at acpi0: C1, PSS
acpicpu2 at acpi0: C1, PSS
acpicpu3 at acpi0: C1, PSS
acpipwrres0 at acpi0: PLPE
acpipwrres1 at acpi0: PLPE
acpipwrres2 at acpi0: USBC, resource for EHC1, OTG1
acpipwrres3 at acpi0: CLK0, resource for CAM1
acpipwrres4 at acpi0: CLK1, resource for CAM0, CAM2
acpipwrres5 at acpi0: FN00, resource for FAN0
acpitz0 at acpi0: critical temperature is 90 degC
acpibat0 at acpi0: BAT0 not present
acpibat1 at acpi0: BAT1 not present
acpibat2 at acpi0: BAT2 not present
acpibtn0 at acpi0: LID0
acpibtn1 at acpi0: PWRB
acpibtn2 at acpi0: SLPB
acpivideo0 at acpi0: GFX0
acpivout0 at acpivideo0: DD1F
cpu0: Enhanced SpeedStep 2000 MHz: speeds: 1993, 1992, 1909, 1826, 1743,
1660, 1577, 1494, 1411, 1328 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 vendor "Intel", unknown product 0x0f00 rev
0x0c
vga1 at pci0 dev 2 function 0 vendor "Intel", unknown product 0x0f31 rev
0x0c
intagp at vga1 not configured
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ahci0 at pci0 dev 19 function 0 vendor "Intel", unknown product 0x0f23 rev
0x0c: msi, AHCI 1.3
scsibus1 at ahci0: 32 targets
sd0 at scsibus1 targ 0 lun 0: <ATA, WDC WD20NPVX-00E, 01.0> SCSI3 0/direct
fixed naa.50014ee260103503
sd0: 1907729MB, 512 bytes/sector, 3907029168 sectors
sd1 at scsibus1 targ 1 lun 0: <ATA, WDC WD20NPVX-00E, 01.0> SCSI3 0/direct
fixed naa.50014ee2b6060356
sd1: 1907729MB, 512 bytes/sector, 3907029168 sectors
vendor "Intel", unknown product 0x0f18 (class crypto subclass
miscellaneous, rev 0x0c) at pci0 dev 26 function 0 not configured
ppb0 at pci0 dev 28 function 0 vendor "Intel", unknown product 0x0f48 rev
0x0c: msi
pci1 at ppb0 bus 1
ppb1 at pci0 dev 28 function 1 vendor "Intel", unknown product 0x0f4a rev
0x0c: msi
pci2 at ppb1 bus 2
re0 at pci2 dev 0 function 0 "Realtek 8168" rev 0x11: RTL8168G/8111G
(0x4c00), msi, address d0:50:99:2b:e9:e0
rgephy0 at re0 phy 7: RTL8251 PHY, rev. 0
ppb2 at pci0 dev 28 function 2 vendor "Intel", unknown product 0x0f4c rev
0x0c: msi
pci3 at ppb2 bus 3
ppb3 at pci0 dev 28 function 3 vendor "Intel", unknown product 0x0f4e rev
0x0c: msi
pci4 at ppb3 bus 4
ehci0 at pci0 dev 29 function 0 vendor "Intel", unknown product 0x0f34 rev
0x0c: apic 1 int 23
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
pcib0 at pci0 dev 31 function 0 vendor "Intel", unknown product 0x0f1c rev
0x0c
vendor "Intel", unknown product 0x0f12 (class serial bus subclass SMBus,
rev 0x0c) at pci0 dev 31 function 3 not configured
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
wbsio0 at isa0 port 0x2e/2: NCT6776F rev 0x33
lm1 at wbsio0 port 0x290/8: NCT6776F
ehci_sync_hc: tsleep() = 35
