Hi,
During the night, my gateway paniced:
OpenBSD 6.0-current (GENERIC.MP) #2366: Wed Aug 17 14:05:46 MDT 2016
[email protected]:/usr/src/sys/arch/amd64/compile/GENERIC.MP
(full dmesg at end).
The system was running since Aug 18 without trouble.
Below is a manual transcription of the console:
panic: kernel diagnostic assertion "ifa == rt->rt_ifa" failed: file
"../../../../netinet6/nd6.c", line 1043
Starting stack trace...
panic() at panic+0x10b
__assert() at __assert+0x25
nd6_rtrequest() at nd6_rtrequest+0x4f4
rtrequest() at rtrequest+0x5b5
rt_match() at rt_match+0xf4
_rtalloc() at _rtalloc+0x18
ip6_input() at ip6_input+0x524
ip6intr() at ip6intr+0x18
if_netisr() at if_netisr+0xf5
taskq_thread() at taskq_thread+0x6c
end trace frame: 0x0, count:247
End of stack trace.
syncing disks... 12 done
The system didn't reboot (whereas ddb.panic=0 was set) neither enter
in ddb(4) (expected due to ddb.panic=0). No savecore at reboot.
So the report could be a bit short, sorry.
Since, I upgraded the system to latest -current (snapshot):
OpenBSD 6.0-current (GENERIC.MP) #2383: Mon Aug 22 17:28:09 MDT 2016
[email protected]:/usr/src/sys/arch/amd64/compile/GENERIC.MP
About the configuration:
- re0 is physical network interface
- several vlans are configured on top of re0
- over vlan10, a pppoe0 interface is configured
The gateway forwards IPv4 and IPv6 traffic.
IPv6 is obtained from pppoe0 via DHCPv6 Delegated Prefix (using dhcpcd
port), and distributed to some others vlans via rtadvd(8).
Thanks.
--
Sebastien Marie
OpenBSD 6.0-current (GENERIC.MP) #2366: Wed Aug 17 14:05:46 MDT 2016
[email protected]:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 921632768 (878MB)
avail mem = 889274368 (848MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.5 @ 0xf0000 (42 entries)
bios0: vendor Phoenix Technologies, LTD version "MS7297 1.08" date 08/22/2007
bios0: Hewlett-Packard 0A7C
acpi0 at bios0: rev 2
acpi0: sleep states S0 S3 S4 S5
acpi0: tables DSDT FACP SSDT HPET MCFG APIC
acpi0: wakeup devices USB0(S3) USB1(S3) USB2(S3) USB3(S3) USB4(S3) USB5(S3)
AZAL(S3) AUDO(S3) MODM(S3) P2P_(S5) RLAN(S5) PCE2(S4) PCE3(S4) PCE4(S4)
PCE5(S4) PCE6(S4) [...]
acpitimer0 at acpi0: 3579545 Hz, 32 bits
acpihpet0 at acpi0: 14318180 Hz
acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: AMD Athlon(tm) 64 X2 Dual Core Processor 5000+, 2593.91 MHz
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW,LAHF,CMPLEG,SVM,EAPICSP,AMCR8,3DNOWP
cpu0: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 512KB 64b/line
16-way L2 cache
cpu0: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu0: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative
mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
cpu0: apic clock running at 199MHz
cpu1 at mainbus0: apid 1 (application processor)
cpu1: AMD Athlon(tm) 64 X2 Dual Core Processor 5000+, 2593.50 MHz
cpu1:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW,LAHF,CMPLEG,SVM,EAPICSP,AMCR8,3DNOWP
cpu1: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 512KB 64b/line
16-way L2 cache
cpu1: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu1: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 21, 24 pins
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 2 (P2P_)
acpiprt2 at acpi0: bus -1 (PCE2)
acpiprt3 at acpi0: bus -1 (PCE3)
acpiprt4 at acpi0: bus -1 (PCE4)
acpiprt5 at acpi0: bus -1 (PCE5)
acpiprt6 at acpi0: bus -1 (PCE6)
acpiprt7 at acpi0: bus -1 (PCE7)
acpiprt8 at acpi0: bus -1 (PCE8)
acpiprt9 at acpi0: bus 1 (AGP_)
acpicpu0 at acpi0: C1(@1 halt!), PSS
acpicpu1 at acpi0: C1(@1 halt!), PSS
acpibtn0 at acpi0: PWRB
"PNP0501" at acpi0 not configured
"PNP0401" at acpi0 not configured
"PNP0303" at acpi0 not configured
cpu0: PowerNow! K8 2593 MHz: speeds: 2600 2400 2200 2000 1800 1000 MHz
pci0 at mainbus0 bus 0
0:18:0: mem address conflict 0xfec01000/0x400
pchb0 at pci0 dev 0 function 0 "ATI RS480 Host" rev 0x10
ppb0 at pci0 dev 1 function 0 "ATI RS480 PCIE" rev 0x00
pci1 at ppb0 bus 1
radeondrm0 at pci1 dev 5 function 0 "ATI Radeon XPRESS 200" rev 0x00
drm0 at radeondrm0
radeondrm0: apic 2 int 17
ahci0 at pci0 dev 18 function 0 "ATI SB600 SATA" rev 0x00: apic 2 int 22, AHCI
1.1
ahci0: port 0: 1.5Gb/s
scsibus1 at ahci0: 32 targets
sd0 at scsibus1 targ 0 lun 0: <ATA, FUJITSU MHV2060B, 0085> SCSI3 0/direct
fixed t10.ATA_FUJITSU_MHV2060BH_NW10T6326AVK
sd0: 55796MB, 512 bytes/sector, 114270345 sectors
ohci0 at pci0 dev 19 function 0 "ATI SB600 USB" rev 0x00: apic 2 int 16,
version 1.0, legacy support
ohci1 at pci0 dev 19 function 1 "ATI SB600 USB" rev 0x00: apic 2 int 17,
version 1.0, legacy support
ohci2 at pci0 dev 19 function 2 "ATI SB600 USB" rev 0x00: apic 2 int 18,
version 1.0, legacy support
ohci3 at pci0 dev 19 function 3 "ATI SB600 USB" rev 0x00: apic 2 int 17,
version 1.0, legacy support
ohci4 at pci0 dev 19 function 4 "ATI SB600 USB" rev 0x00: apic 2 int 18,
version 1.0, legacy support
ehci0 at pci0 dev 19 function 5 "ATI SB600 USB2" rev 0x00: apic 2 int 19
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "ATI EHCI root hub" rev 2.00/1.00 addr 1
piixpm0 at pci0 dev 20 function 0 "ATI SBx00 SMBus" rev 0x13: SMI
iic0 at piixpm0
iic0: addr 0x2f 00=c2 01=0f 02=00 03=00 04=07 05=20 06=18 07=01 08=00 14=14
15=62 16=02 17=05 words 00=c2ff 01=0fff 02=00ff 03=00ff 04=07ff 05=20ff 06=18ff
07=01ff
spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-5300CL5
pciide0 at pci0 dev 20 function 1 "ATI SB600 IDE" rev 0x00: DMA, channel 0
configured to native-PCI, channel 1 configured to native-PCI
pciide0: using apic 2 int 16 for native-PCI interrupt
azalia0 at pci0 dev 20 function 2 "ATI SBx00 HD Audio" rev 0x00: apic 2 int 23
azalia0: codecs: Realtek/0x0862
audio0 at azalia0
pcib0 at pci0 dev 20 function 3 "ATI SB600 ISA" rev 0x00
ppb1 at pci0 dev 20 function 4 "ATI SB600 PCI" rev 0x00
pci2 at ppb1 bus 2
re0 at pci2 dev 2 function 0 "D-Link DGE-528T" rev 0x10: RTL8169/8110SB
(0x1000), apic 2 int 22, address c8:be:19:e2:2c:ed
rgephy0 at re0 phy 7: RTL8169S/8110S/8211 PHY, rev. 3
rl0 at pci2 dev 6 function 0 "Realtek 8139" rev 0x10: apic 2 int 21, address
00:1d:92:43:43:95
rlphy0 at rl0 phy 0: RTL internal PHY
pchb1 at pci0 dev 24 function 0 "AMD AMD64 0Fh HyperTransport" rev 0x00
pchb2 at pci0 dev 24 function 1 "AMD AMD64 0Fh Address Map" rev 0x00
pchb3 at pci0 dev 24 function 2 "AMD AMD64 0Fh DRAM Cfg" rev 0x00
kate0 at pci0 dev 24 function 3 "AMD AMD64 0Fh Misc Cfg" rev 0x00: core rev
BH-G1
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb2 at ohci1: USB revision 1.0
uhub2 at usb2 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb3 at ohci2: USB revision 1.0
uhub3 at usb3 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb4 at ohci3: USB revision 1.0
uhub4 at usb4 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb5 at ohci4: USB revision 1.0
uhub5 at usb5 "ATI OHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5 irq 1 irq 12
pckbd0 at pckbc0 (kbd slot)
wskbd0 at pckbd0: console keyboard
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
wbsio0 at isa0 port 0x4e/2: W83627EHF rev 0x68
lm1 at wbsio0 port 0x260/8: W83627EHF
umass0 at uhub0 port 7 configuration 1 interface 0 "Generic USB2.0-CRW" rev
2.00/11.22 addr 2
umass0: using SCSI over Bulk-Only
scsibus2 at umass0: 2 targets, initiator 0
sd1 at scsibus2 targ 1 lun 0: <Generic-, Compact Flash, 1.00> SCSI0 0/direct
removable
sd2 at scsibus2 targ 1 lun 1: <Generic-, SM/xD-Picture, 1.00> SCSI0 0/direct
removable
sd3 at scsibus2 targ 1 lun 2: <Generic-, SD/MMC, 1.00> SCSI0 0/direct removable
sd4 at scsibus2 targ 1 lun 3: <Generic-, MS/MS-Pro, 1.00> SCSI0 0/direct
removable
vscsi0 at root
scsibus3 at vscsi0: 256 targets
softraid0 at root
scsibus4 at softraid0: 256 targets
root on sd0a (dd15967b7ad164f3.a) swap on sd0b dump on sd0b
WARNING: / was not properly unmounted
radeondrm0: 1280x1024
wsdisplay0 at radeondrm0 mux 1: console (std, vt100 emulation), using wskbd0
wsdisplay0: screen 1-5 added (std, vt100 emulation)
