With the latest snapshot, I'm once again able to cold-boot my Wandboard.
Latest dmesg follows:
OpenBSD 6.0-current (GENERIC) #45: Tue Sep 13 03:12:56 MDT 2016
[email protected]:/usr/src/sys/arch/armv7/compile/GENERIC
real mem = 2147483648 (2048MB)
avail mem = 2097598464 (2000MB)
mainbus0 at root: Wandboard i.MX6 Quad Board
cpu0 at mainbus0: ARM Cortex A9 R2 rev 10 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
cortex0 at mainbus0
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 7 waymask: 0x0000000f
imx0 at mainbus0
imxccm0 at imx0: imx6 rev 1.5 CPU freq: 792 MHz
imxiomuxc0 at imx0
imxocotp0 at imx0
simplebus0 at mainbus0: "soc"
ampintc0 at simplebus0 nirq 160
simplebus1 at simplebus0: "aips-bus"
simplebus2 at simplebus1: "spba-bus"
imxuart0 at simplebus2: console
imxgpio0 at simplebus1
imxgpio1 at simplebus1
imxgpio2 at simplebus1
imxgpio3 at simplebus1
imxgpio4 at simplebus1
imxgpio5 at simplebus1
imxgpio6 at simplebus1
imxdog0 at simplebus1
imxtemp0 at simplebus1
imxgpc0 at simplebus1
simplebus3 at simplebus0: "aips-bus"
imxehci0 at simplebus3
usb0 at imxehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "i.MX6 EHCI root hub" rev
2.00/1.00 addr 1
imxehci1 at simplebus3
usb1 at imxehci1: USB revision 2.0
uhub1 at usb1 configuration 1 interface 0 "i.MX6 EHCI root hub" rev
2.00/1.00 addr 1
fec0 at simplebus3
fec0: address 00:1f:7b:b4:22:5f
atphy0 at fec0 phy 1: AR8035 10/100/1000 PHY, rev. 4
imxesdhc0 at simplebus3
imxesdhc0: 198 MHz base clock
sdmmc0 at imxesdhc0: 4-bit, mmc high-speed, dma
imxesdhc1 at simplebus3
imxesdhc1: 198 MHz base clock
sdmmc1 at imxesdhc1: 4-bit, mmc high-speed, dma
imxesdhc2 at simplebus3
imxesdhc2: 198 MHz base clock
sdmmc2 at imxesdhc2: 4-bit, mmc high-speed, dma
imxiic0 at simplebus3
iic0 at imxiic0
imxiic1 at simplebus3
iic1 at imxiic1
"fsl,sgtl5000" at iic1 addr 0xa not configured
imxuart1 at simplebus3
imxahci0 at simplebus0: AHCI 1.3
scsibus0 at imxahci0: 32 targets
simplebus4 at mainbus0: "regulators"
scsibus1 at sdmmc2: 2 targets, initiator 0
sd0 at scsibus1 targ 1 lun 0: <SD/MMC, 00000, 0010> SCSI2 0/direct fixed
sd0: 61056MB, 512 bytes/sector, 125042688 sectors
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
boot device: sd0
root on sd0a (3c60000fd48d06a0.a) swap on sd0b dump on sd0b
WARNING: CHECK AND RESET THE DATE!
On Mon, September 12, 2016 9:13 pm, Jonathan Gray wrote:
> As the 23rd is when sys/dev/ofw/fdt.c 1.19
>
> ----------------------------
> revision 1.19
> date: 2016/08/23 18:12:09; author: kettenis; state: Exp; lines: +4 -1;
> commitid: QVPcH04Hp9qQOAgf;
> Actually make fdt_find_node() return NULL if the node couldn't be found.
>
> ok tom@
> ----------------------------
>
> was committed, the commit matthieu@ reported fec(4) problems on
> sabre lite with, try a snapshot after sys/arch/armv7/imx/imxiomuxc.c 1.7
>
> ----------------------------
> revision 1.7
> date: 2016/09/10 18:33:01; author: jsg; state: Exp; lines: +2 -2;
> commitid: cFRL5ZcH1S6dcfC1;
> Correct the path to the iomuxc fdt node so pinctrl setup will run.
> Noticed when looking into a regression on sabre lite with fec(4)
> bisected by matthieu@. This fixes the sabre lite problems with fec and
> also recent problems with the i2c rtc on cubox.
>
> ok kettenis@
> ----------------------------
>
> On Mon, Sep 12, 2016 at 08:51:46PM -0400, Joe Gidi wrote:
>> My Wandboard Quad is unable to successfully cold-boot with any snapshot
>> after August 23rd. I can successfully reboot into later kernels after an
>> initial boot with the 8/23 kernel, but on cold boot they hang at this
>> line:
>>
>> simplebus5 at mainbus0: "regulators"
>>
>> It appears something is no longer being initialized properly during the
>> boot process.
>>
>> Full dmesg of the last working snapshot kernel and 'eeprom -p' output
>> are
>> attached. Please let me know if I can provide any further information.
>>
>> --
>> Joe Gidi
>> [email protected]
>>
>> "You cannot buy skill." -- Ross Seyfried
>
>> OpenBSD 6.0-current (GENERIC) #32: Tue Aug 23 03:13:41 MDT 2016
>> [email protected]:/usr/src/sys/arch/armv7/compile/GENERIC
>> real mem = 2147483648 (2048MB)
>> avail mem = 2097623040 (2000MB)
>> mainbus0 at root: Wandboard i.MX6 Quad Board
>> cpu0 at mainbus0: ARM Cortex A9 R2 rev 10 (ARMv7 core)
>> cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
>> cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
>> cortex0 at mainbus0
>> amptimer0 at cortex0: tick rate 396000 KHz
>> armliicc0 at cortex0: rtl 7 waymask: 0x0000000f
>> imx0 at mainbus0
>> imxccm0 at imx0: imx6 rev 1.5 CPU freq: 792 MHz
>> imxiomuxc0 at imx0
>> imxocotp0 at imx0
>> simplebus0 at mainbus0: "soc"
>> ampintc0 at simplebus0 nirq 160
>> simplebus1 at simplebus0: "aips-bus"
>> simplebus2 at simplebus1: "spba-bus"
>> imxuart0 at simplebus2: console
>> imxgpio0 at simplebus1
>> imxgpio1 at simplebus1
>> imxgpio2 at simplebus1
>> imxgpio3 at simplebus1
>> imxgpio4 at simplebus1
>> imxgpio5 at simplebus1
>> imxgpio6 at simplebus1
>> imxdog0 at simplebus1
>> imxtemp0 at simplebus1
>> imxgpc0 at simplebus1
>> simplebus3 at simplebus0: "aips-bus"
>> imxehci0 at simplebus3
>> usb0 at imxehci0: USB revision 2.0
>> uhub0 at usb0 "i.MX6 EHCI root hub" rev 2.00/1.00 addr 1
>> imxehci1 at simplebus3
>> usb1 at imxehci1: USB revision 2.0
>> uhub1 at usb1 "i.MX6 EHCI root hub" rev 2.00/1.00 addr 1
>> fec0 at simplebus3
>> fec0: address 00:1f:7b:b4:22:5f
>> atphy0 at fec0 phy 1: AR8035 10/100/1000 PHY, rev. 4
>> imxesdhc0 at simplebus3
>> imxesdhc0: 198 MHz base clock
>> sdmmc0 at imxesdhc0: 4-bit, mmc high-speed, dma
>> imxesdhc1 at simplebus3
>> imxesdhc1: 198 MHz base clock
>> sdmmc1 at imxesdhc1: 4-bit, mmc high-speed, dma
>> imxesdhc2 at simplebus3
>> imxesdhc2: 198 MHz base clock
>> sdmmc2 at imxesdhc2: 4-bit, mmc high-speed, dma
>> imxiic0 at simplebus3
>> iic0 at imxiic0
>> imxiic1 at simplebus3
>> iic1 at imxiic1
>> "fsl,sgtl5000" at iic1 addr 0xa not configured
>> imxuart1 at simplebus3
>> imxahci0 at simplebus0: AHCI 1.3
>> scsibus0 at imxahci0: 32 targets
>> simplebus4 at mainbus0: "regulators"
>> scsibus1 at sdmmc2: 2 targets, initiator 0
>> sd0 at scsibus1 targ 1 lun 0: <SD/MMC, 00000, 0010> SCSI2 0/direct fixed
>> sd0: 61056MB, 512 bytes/sector, 125042688 sectors
>> vscsi0 at root
>> scsibus2 at vscsi0: 256 targets
>> softraid0 at root
>> scsibus3 at softraid0: 256 targets
>> boot device: sd0
>> root on sd0a (3c60000fd48d06a0.a) swap on sd0b dump on sd0b
>> WARNING: CHECK AND RESET THE DATE!
>
>> Node 0x48
>> name: ''
>> #address-cells: 00000001
>> #size-cells: 00000001
>> model: 'Wandboard i.MX6 Quad Board'
>> compatible: 'wand,imx6q-wandboard' + 'fsl,imx6q'
>>
>> Node 0xc4
>> name: 'chosen'
>> openbsd,bootduid: 3c60000f.d48d06a0
>> bootargs: 'sd0a:/bsd'
>>
>> Node 0x100
>> name: 'aliases'
>> ethernet0: '/soc/aips-bus@02100000/ethernet@02188000'
>> can0: '/soc/aips-bus@02000000/flexcan@02090000'
>> can1: '/soc/aips-bus@02000000/flexcan@02094000'
>> gpio0: '/soc/aips-bus@02000000/gpio@0209c000'
>> gpio1: '/soc/aips-bus@02000000/gpio@020a0000'
>> gpio2: '/soc/aips-bus@02000000/gpio@020a4000'
>> gpio3: '/soc/aips-bus@02000000/gpio@020a8000'
>> gpio4: '/soc/aips-bus@02000000/gpio@020ac000'
>> gpio5: '/soc/aips-bus@02000000/gpio@020b0000'
>> gpio6: '/soc/aips-bus@02000000/gpio@020b4000'
>> i2c0: '/soc/aips-bus@02100000/i2c@021a0000'
>> i2c1: '/soc/aips-bus@02100000/i2c@021a4000'
>> i2c2: '/soc/aips-bus@02100000/i2c@021a8000'
>> ipu0: '/soc/ipu@02400000'
>> mmc0: '/soc/aips-bus@02100000/usdhc@02190000'
>> mmc1: '/soc/aips-bus@02100000/usdhc@02194000'
>> mmc2: '/soc/aips-bus@02100000/usdhc@02198000'
>> mmc3: '/soc/aips-bus@02100000/usdhc@0219c000'
>> serial0:
>> '/soc/aips-bus@02000000/spba-bus@02000000/serial@02020000'
>> serial1: '/soc/aips-bus@02100000/serial@021e8000'
>> serial2: '/soc/aips-bus@02100000/serial@021ec000'
>> serial3: '/soc/aips-bus@02100000/serial@021f0000'
>> serial4: '/soc/aips-bus@02100000/serial@021f4000'
>> spi0: '/soc/aips-bus@02000000/spba-bus@02000000/ecspi@02008000'
>> spi1: '/soc/aips-bus@02000000/spba-bus@02000000/ecspi@0200c000'
>> spi2: '/soc/aips-bus@02000000/spba-bus@02000000/ecspi@02010000'
>> spi3: '/soc/aips-bus@02000000/spba-bus@02000000/ecspi@02014000'
>> usbphy0: '/soc/aips-bus@02000000/usbphy@020c9000'
>> usbphy1: '/soc/aips-bus@02000000/usbphy@020ca000'
>> ipu1: '/soc/ipu@02800000'
>> spi4: '/soc/aips-bus@02000000/spba-bus@02000000/ecspi@02018000'
>>
>> Node 0x790
>> name: 'memory'
>> device_type: 'memory'
>> reg: 10000000.80000000
>>
>> Node 0x7c8
>> name: 'clocks'
>> #address-cells: 00000001
>> #size-cells: 00000000
>>
>> Node 0x7f4
>> name: 'ckil'
>> compatible: 'fsl,imx-ckil' + 'fixed-clock'
>> #clock-cells: 00000000
>> clock-frequency: 00008000
>>
>> Node 0x84c
>> name: 'ckih1'
>> compatible: 'fsl,imx-ckih1' + 'fixed-clock'
>> #clock-cells: 00000000
>> clock-frequency: 00000000
>>
>> Node 0x8a4
>> name: 'osc'
>> compatible: 'fsl,imx-osc' + 'fixed-clock'
>> #clock-cells: 00000000
>> clock-frequency: 016e3600
>>
>> Node 0x8f8
>> name: 'soc'
>> #address-cells: 00000001
>> #size-cells: 00000001
>> compatible: 'simple-bus'
>> interrupt-parent: 00000001
>> ranges:
>>
>> Node 0x954
>> name: 'dma-apbh'
>> compatible: 'fsl,imx6q-dma-apbh' + 'fsl,imx28-dma-apbh'
>> reg: 00110000.00002000
>> interrupts:
>> 00000000.0000000d.00000004.00000000.0000000d.00000004.00000000.0000000d.00000004.00000000.0000000d.00000004
>> interrupt-names: 'gpmi0' + 'gpmi1' + 'gpmi2' + 'gpmi3'
>> #dma-cells: 00000001
>> dma-channels: 00000004
>> clocks: 00000002.0000006a
>> linux,phandle: 00000003
>> phandle: 00000003
>>
>> Node 0xa6c
>> name: 'gpmi-nand'
>> compatible: 'fsl,imx6q-gpmi-nand'
>> #address-cells: 00000001
>> #size-cells: 00000001
>> reg: 00112000.00002000.00114000.00002000
>> reg-names: 'gpmi-nand' + 'bch'
>> interrupts: 00000000.0000000f.00000004
>> interrupt-names: 'bch'
>> clocks:
>> 00000002.00000098.00000002.00000099.00000002.00000097.00000002.00000096.00000002.00000095
>> clock-names: 'gpmi_io' + 'gpmi_apb' + 'gpmi_bch' +
>> 'gpmi_bch_apb' + 'per1_bch'
>> dmas: 00000003.00000000
>> dma-names: 'rx-tx'
>> status: 'disabled'
>>
>> Node 0xbd8
>> name: 'hdmi'
>> #address-cells: 00000001
>> #size-cells: 00000000
>> reg: 00120000.00009000
>> interrupts: 00000000.00000073.00000004
>> gpr: 00000004
>> clocks: 00000002.0000007b.00000002.0000007c
>> clock-names: 'iahb' + 'isfr'
>> status: 'okay'
>> compatible: 'fsl,imx6q-hdmi'
>> ddc-i2c-bus: 00000005
>>
>> Node 0xcbc
>> name: 'port'
>> reg: 00000000
>>
>> Node 0xcd8
>> name: 'endpoint'
>> remote-endpoint: 00000006
>> linux,phandle: 00000031
>> phandle: 00000031
>>
>> Node 0xd20
>> name: 'port'
>> reg: 00000001
>>
>> Node 0xd3c
>> name: 'endpoint'
>> remote-endpoint: 00000007
>> linux,phandle: 00000035
>> phandle: 00000035
>>
>> Node 0xd84
>> name: 'port'
>> reg: 00000002
>>
>> Node 0xda0
>> name: 'endpoint'
>> remote-endpoint: 00000008
>> linux,phandle: 00000039
>> phandle: 00000039
>>
>> Node 0xde8
>> name: 'port'
>> reg: 00000003
>>
>> Node 0xe04
>> name: 'endpoint'
>> remote-endpoint: 00000009
>> linux,phandle: 0000003d
>> phandle: 0000003d
>>
>> Node 0xe50
>> name: 'gpu'
>> compatible: 'vivante,gc'
>> reg: 00130000.00004000
>> interrupts: 00000000.00000009.00000004
>> clocks:
>> 00000002.0000001b.00000002.0000007a.00000002.0000004a
>> clock-names: 'bus' + 'core' + 'shader'
>> power-domains: 00000001.00000001
>> linux,phandle: 00000049
>> phandle: 00000049
>>
>> Node 0xf20
>> name: 'gpu'
>> compatible: 'vivante,gc'
>> reg: 00134000.00004000
>> interrupts: 00000000.0000000a.00000004
>> clocks: 00000002.0000001a.00000002.00000079
>> clock-names: 'bus' + 'core'
>> power-domains: 00000001.00000001
>> linux,phandle: 00000048
>> phandle: 00000048
>>
>> Node 0xfe4
>> name: 'timer'
>> compatible: 'arm,cortex-a9-twd-timer'
>> reg: 00a00600.00000020
>> interrupts: 00000001.0000000d.00000f01
>> interrupt-parent: 0000000a
>> clocks: 00000002.0000000f
>>
>> Node 0x1070
>> name: 'interrupt-controller'
>> compatible: 'arm,cortex-a9-gic'
>> #interrupt-cells: 00000003
>> interrupt-controller:
>> reg: 00a01000.00001000.00a00100.00000100
>> interrupt-parent: 0000000a
>> linux,phandle: 0000000a
>> phandle: 0000000a
>>
>> Node 0x1120
>> name: 'l2-cache'
>> compatible: 'arm,pl310-cache'
>> reg: 00a02000.00001000
>> interrupts: 00000000.0000005c.00000004
>> cache-unified:
>> cache-level: 00000002
>> arm,tag-latency: 00000004.00000002.00000003
>> arm,data-latency: 00000004.00000002.00000003
>> linux,phandle: 00000041
>> phandle: 00000041
>>
>> Node 0x11f0
>> name: 'pcie'
>> compatible: 'fsl,imx6q-pcie' + 'snps,dw-pcie'
>> reg: 01ffc000.00004000.01f00000.00080000
>> reg-names: 'dbi' + 'config'
>> #address-cells: 00000003
>> #size-cells: 00000002
>> device_type: 'pci'
>> ranges:
>> 81000000.00000000.00000000.01f80000.00000000.00010000.82000000.00000000.01000000.01000000.00000000.00f00000
>> num-lanes: 00000001
>> interrupts: 00000000.00000078.00000004
>> interrupt-names: 'msi'
>> #interrupt-cells: 00000001
>> interrupt-map-mask: 00000000.00000000.00000000.00000007
>> interrupt-map:
>> 00000000.00000000.00000000.00000001.00000001.00000000.0000007b.00000004.00000000.00000000.00000000.00000002.00000001.00000000.0000007a.00000004.00000000.00000000.00000000.00000003.00000001.00000000.00000079.00000004.00000000.00000000.00000000.00000004.00000001.00000000.00000078.00000004
>> clocks:
>> 00000002.00000090.00000002.000000ce.00000002.000000bd
>> clock-names: 'pcie' + 'pcie_bus' + 'pcie_phy'
>> status: 'disabled'
>>
>> Node 0x1420
>> name: 'pmu'
>> compatible: 'arm,cortex-a9-pmu'
>> interrupts: 00000000.0000005e.00000004
>>
>> Node 0x1464
>> name: 'aips-bus'
>> compatible: 'fsl,aips-bus' + 'simple-bus'
>> #address-cells: 00000001
>> #size-cells: 00000001
>> reg: 02000000.00100000
>> ranges:
>>
>> Node 0x14e0
>> name: 'spba-bus'
>> compatible: 'fsl,spba-bus' + 'simple-bus'
>> #address-cells: 00000001
>> #size-cells: 00000001
>> reg: 02000000.00040000
>> ranges:
>>
>> Node 0x155c
>> name: 'spdif'
>> compatible: 'fsl,imx35-spdif'
>> reg: 02004000.00004000
>> interrupts: 00000000.00000034.00000004
>> dmas:
>> 0000000b.0000000e.00000012.00000000.0000000b.0000000f.00000012.00000000
>> dma-names: 'rx' + 'tx'
>> clocks:
>> 00000002.000000f4.00000002.00000003.00000002.000000c5.00000002.0000006b.00000002.00000000.00000002.00000076.00000002.0000003e.00000002.0000008b.00000002.00000000.00000002.0000009c
>> clock-names: 'core' + 'rxtx0' + 'rxtx1' + 'rxtx2' +
>> 'rxtx3' + 'rxtx4' + 'rxtx5' + 'rxtx6' + 'rxtx7' +
>> 'spba'
>> status: 'okay'
>> pinctrl-names: 'default'
>> pinctrl-0: 0000000c
>> linux,phandle: 0000004d
>> phandle: 0000004d
>>
>> Node 0x16f8
>> name: 'ecspi'
>> #address-cells: 00000001
>> #size-cells: 00000000
>> compatible: 'fsl,imx6q-ecspi' + 'fsl,imx51-ecspi'
>> reg: 02008000.00004000
>> interrupts: 00000000.0000001f.00000004
>> clocks: 00000002.00000070.00000002.00000070
>> clock-names: 'ipg' + 'per'
>> dmas:
>> 0000000b.00000003.00000008.00000001.0000000b.00000004.00000008.00000002
>> dma-names: 'rx' + 'tx'
>> status: 'disabled'
>>
>> Node 0x1810
>> name: 'ecspi'
>> #address-cells: 00000001
>> #size-cells: 00000000
>> compatible: 'fsl,imx6q-ecspi' + 'fsl,imx51-ecspi'
>> reg: 0200c000.00004000
>> interrupts: 00000000.00000020.00000004
>> clocks: 00000002.00000071.00000002.00000071
>> clock-names: 'ipg' + 'per'
>> dmas:
>> 0000000b.00000005.00000008.00000001.0000000b.00000006.00000008.00000002
>> dma-names: 'rx' + 'tx'
>> status: 'disabled'
>>
>> Node 0x1928
>> name: 'ecspi'
>> #address-cells: 00000001
>> #size-cells: 00000000
>> compatible: 'fsl,imx6q-ecspi' + 'fsl,imx51-ecspi'
>> reg: 02010000.00004000
>> interrupts: 00000000.00000021.00000004
>> clocks: 00000002.00000072.00000002.00000072
>> clock-names: 'ipg' + 'per'
>> dmas:
>> 0000000b.00000007.00000008.00000001.0000000b.00000008.00000008.00000002
>> dma-names: 'rx' + 'tx'
>> status: 'disabled'
>>
>> Node 0x1a40
>> name: 'ecspi'
>> #address-cells: 00000001
>> #size-cells: 00000000
>> compatible: 'fsl,imx6q-ecspi' + 'fsl,imx51-ecspi'
>> reg: 02014000.00004000
>> interrupts: 00000000.00000022.00000004
>> clocks: 00000002.00000073.00000002.00000073
>> clock-names: 'ipg' + 'per'
>> dmas:
>> 0000000b.00000009.00000008.00000001.0000000b.0000000a.00000008.00000002
>> dma-names: 'rx' + 'tx'
>> status: 'disabled'
>>
>> Node 0x1b58
>> name: 'serial'
>> compatible: 'fsl,imx6q-uart' + 'fsl,imx21-uart'
>> reg: 02020000.00004000
>> interrupts: 00000000.0000001a.00000004
>> clocks: 00000002.000000a0.00000002.000000a1
>> clock-names: 'ipg' + 'per'
>> dmas:
>> 0000000b.00000019.00000004.00000000.0000000b.0000001a.00000004.00000000
>> dma-names: 'rx' + 'tx'
>> status: 'okay'
>> pinctrl-names: 'default'
>> pinctrl-0: 0000000d
>>
>> Node 0x1c70
>> name: 'esai'
>> #sound-dai-cells: 00000000
>> compatible: 'fsl,imx35-esai'
>> reg: 02024000.00004000
>> interrupts: 00000000.00000033.00000004
>> clocks:
>> 00000002.000000d0.00000002.000000d1.00000002.00000076.00000002.000000d0.00000002.0000009c
>> clock-names: 'core' + 'mem' + 'extal' + 'fsys' +
>> 'spba'
>> dmas:
>> 0000000b.00000017.00000015.00000000.0000000b.00000018.00000015.00000000
>> dma-names: 'rx' + 'tx'
>> status: 'disabled'
>>
>> Node 0x1d94
>> name: 'ssi'
>> #sound-dai-cells: 00000000
>> compatible: 'fsl,imx6q-ssi' + 'fsl,imx51-ssi'
>> reg: 02028000.00004000
>> interrupts: 00000000.0000002e.00000004
>> clocks: 00000002.000000b2.00000002.0000009d
>> clock-names: 'ipg' + 'baud'
>> dmas:
>> 0000000b.00000025.00000001.00000000.0000000b.00000026.00000001.00000000
>> dma-names: 'rx' + 'tx'
>> fsl,fifo-depth: 0000000f
>> status: 'okay'
>> linux,phandle: 0000004b
>> phandle: 0000004b
>>
>> Node 0x1ec8
>> name: 'ssi'
>> #sound-dai-cells: 00000000
>> compatible: 'fsl,imx6q-ssi' + 'fsl,imx51-ssi'
>> reg: 0202c000.00004000
>> interrupts: 00000000.0000002f.00000004
>> clocks: 00000002.000000b3.00000002.0000009e
>> clock-names: 'ipg' + 'baud'
>> dmas:
>> 0000000b.00000029.00000001.00000000.0000000b.0000002a.00000001.00000000
>> dma-names: 'rx' + 'tx'
>> fsl,fifo-depth: 0000000f
>> status: 'disabled'
>>
>> Node 0x1fe0
>> name: 'ssi'
>> #sound-dai-cells: 00000000
>> compatible: 'fsl,imx6q-ssi' + 'fsl,imx51-ssi'
>> reg: 02030000.00004000
>> interrupts: 00000000.00000030.00000004
>> clocks: 00000002.000000b4.00000002.0000009f
>> clock-names: 'ipg' + 'baud'
>> dmas:
>> 0000000b.0000002d.00000001.00000000.0000000b.0000002e.00000001.00000000
>> dma-names: 'rx' + 'tx'
>> fsl,fifo-depth: 0000000f
>> status: 'disabled'
>>
>> Node 0x20f8
>> name: 'asrc'
>> compatible: 'fsl,imx53-asrc'
>> reg: 02034000.00004000
>> interrupts: 00000000.00000032.00000004
>> clocks:
>> 00000002.000000d2.00000002.000000d3.00000002.00000000.00000002.00000000.00000002.00000000.00000002.00000000.00000002.00000000.00000002.00000000.00000002.00000000.00000002.00000000.00000002.00000000.00000002.00000000.00000002.00000000.00000002.00000000.00000002.00000000.00000002.0000006b.00000002.00000000.00000002.00000000.00000002.0000009c
>> clock-names: 'mem' + 'ipg' + 'asrck_0' + 'asrck_1' +
>> 'asrck_2' + 'asrck_3' + 'asrck_4' + 'asrck_5' +
>> 'asrck_6' + 'asrck_7' + 'asrck_8' + 'asrck_9' +
>> 'asrck_a' + 'asrck_b' + 'asrck_c' + 'asrck_d' +
>> 'asrck_e' + 'asrck_f' + 'spba'
>> dmas:
>> 0000000b.00000011.00000017.00000001.0000000b.00000012.00000017.00000001.0000000b.00000013.00000017.00000001.0000000b.00000014.00000017.00000001.0000000b.00000015.00000017.00000001.0000000b.00000016.00000017.00000001
>> dma-names: 'rxa' + 'rxb' + 'rxc' + 'txa' + 'txb' +
>> 'txc'
>> fsl,asrc-rate: 0000bb80
>> fsl,asrc-width: 00000010
>> status: 'okay'
>>
>> Node 0x235c
>> name: 'spba'
>> reg: 0203c000.00004000
>>
>> Node 0x2388
>> name: 'ecspi'
>> #address-cells: 00000001
>> #size-cells: 00000000
>> compatible: 'fsl,imx6q-ecspi' + 'fsl,imx51-ecspi'
>> reg: 02018000.00004000
>> interrupts: 00000000.00000023.00000004
>> clocks: 00000002.00000074.00000002.00000074
>> clock-names: 'ipg' + 'per'
>> dmas:
>> 0000000b.0000000b.00000007.00000001.0000000b.0000000c.00000007.00000002
>> dma-names: 'rx' + 'tx'
>> status: 'disabled'
>>
>> Node 0x24a4
>> name: 'vpu'
>> compatible: 'fsl,imx6q-vpu' + 'cnm,coda960'
>> reg: 02040000.0003c000
>> interrupts:
>> 00000000.0000000c.00000004.00000000.00000003.00000004
>> interrupt-names: 'bit' + 'jpeg'
>> clocks: 00000002.000000a8.00000002.0000008c
>> clock-names: 'per' + 'ahb'
>> power-domains: 00000001.00000001
>> resets: 0000000e.00000001
>> iram: 0000000f
>>
>> Node 0x259c
>> name: 'aipstz'
>> reg: 0207c000.00004000
>>
>> Node 0x25c8
>> name: 'pwm'
>> #pwm-cells: 00000002
>> compatible: 'fsl,imx6q-pwm' + 'fsl,imx27-pwm'
>> reg: 02080000.00004000
>> interrupts: 00000000.00000053.00000004
>> clocks: 00000002.0000003e.00000002.00000091
>> clock-names: 'ipg' + 'per'
>> status: 'disabled'
>>
>> Node 0x268c
>> name: 'pwm'
>> #pwm-cells: 00000002
>> compatible: 'fsl,imx6q-pwm' + 'fsl,imx27-pwm'
>> reg: 02084000.00004000
>> interrupts: 00000000.00000054.00000004
>> clocks: 00000002.0000003e.00000002.00000092
>> clock-names: 'ipg' + 'per'
>> status: 'disabled'
>>
>> Node 0x2750
>> name: 'pwm'
>> #pwm-cells: 00000002
>> compatible: 'fsl,imx6q-pwm' + 'fsl,imx27-pwm'
>> reg: 02088000.00004000
>> interrupts: 00000000.00000055.00000004
>> clocks: 00000002.0000003e.00000002.00000093
>> clock-names: 'ipg' + 'per'
>> status: 'disabled'
>>
>> Node 0x2814
>> name: 'pwm'
>> #pwm-cells: 00000002
>> compatible: 'fsl,imx6q-pwm' + 'fsl,imx27-pwm'
>> reg: 0208c000.00004000
>> interrupts: 00000000.00000056.00000004
>> clocks: 00000002.0000003e.00000002.00000094
>> clock-names: 'ipg' + 'per'
>> status: 'disabled'
>>
>> Node 0x28d8
>> name: 'flexcan'
>> compatible: 'fsl,imx6q-flexcan'
>> reg: 02090000.00004000
>> interrupts: 00000000.0000006e.00000004
>> clocks: 00000002.0000006c.00000002.0000006d
>> clock-names: 'ipg' + 'per'
>> status: 'disabled'
>>
>> Node 0x2988
>> name: 'flexcan'
>> compatible: 'fsl,imx6q-flexcan'
>> reg: 02094000.00004000
>> interrupts: 00000000.0000006f.00000004
>> clocks: 00000002.0000006e.00000002.0000006f
>> clock-names: 'ipg' + 'per'
>> status: 'disabled'
>>
>> Node 0x2a38
>> name: 'gpt'
>> compatible: 'fsl,imx6q-gpt' + 'fsl,imx31-gpt'
>> reg: 02098000.00004000
>> interrupts: 00000000.00000037.00000004
>> clocks:
>> 00000002.00000077.00000002.00000078.00000002.000000ed
>> clock-names: 'ipg' + 'per' + 'osc_per'
>>
>> Node 0x2ae4
>> name: 'gpio'
>> compatible: 'fsl,imx6q-gpio' + 'fsl,imx35-gpio'
>> reg: 0209c000.00004000
>> interrupts:
>> 00000000.00000042.00000004.00000000.00000043.00000004
>> gpio-controller:
>> #gpio-cells: 00000002
>> interrupt-controller:
>> #interrupt-cells: 00000002
>> linux,phandle: 00000021
>> phandle: 00000021
>>
>> Node 0x2bb8
>> name: 'gpio'
>> compatible: 'fsl,imx6q-gpio' + 'fsl,imx35-gpio'
>> reg: 020a0000.00004000
>> interrupts:
>> 00000000.00000044.00000004.00000000.00000045.00000004
>> gpio-controller:
>> #gpio-cells: 00000002
>> interrupt-controller:
>> #interrupt-cells: 00000002
>>
>> Node 0x2c6c
>> name: 'gpio'
>> compatible: 'fsl,imx6q-gpio' + 'fsl,imx35-gpio'
>> reg: 020a4000.00004000
>> interrupts:
>> 00000000.00000046.00000004.00000000.00000047.00000004
>> gpio-controller:
>> #gpio-cells: 00000002
>> interrupt-controller:
>> #interrupt-cells: 00000002
>> linux,phandle: 00000023
>> phandle: 00000023
>>
>> Node 0x2d40
>> name: 'gpio'
>> compatible: 'fsl,imx6q-gpio' + 'fsl,imx35-gpio'
>> reg: 020a8000.00004000
>> interrupts:
>> 00000000.00000048.00000004.00000000.00000049.00000004
>> gpio-controller:
>> #gpio-cells: 00000002
>> interrupt-controller:
>> #interrupt-cells: 00000002
>>
>> Node 0x2df4
>> name: 'gpio'
>> compatible: 'fsl,imx6q-gpio' + 'fsl,imx35-gpio'
>> reg: 020ac000.00004000
>> interrupts:
>> 00000000.0000004a.00000004.00000000.0000004b.00000004
>> gpio-controller:
>> #gpio-cells: 00000002
>> interrupt-controller:
>> #interrupt-cells: 00000002
>>
>> Node 0x2ea8
>> name: 'gpio'
>> compatible: 'fsl,imx6q-gpio' + 'fsl,imx35-gpio'
>> reg: 020b0000.00004000
>> interrupts:
>> 00000000.0000004c.00000004.00000000.0000004d.00000004
>> gpio-controller:
>> #gpio-cells: 00000002
>> interrupt-controller:
>> #interrupt-cells: 00000002
>>
>> Node 0x2f5c
>> name: 'gpio'
>> compatible: 'fsl,imx6q-gpio' + 'fsl,imx35-gpio'
>> reg: 020b4000.00004000
>> interrupts:
>> 00000000.0000004e.00000004.00000000.0000004f.00000004
>> gpio-controller:
>> #gpio-cells: 00000002
>> interrupt-controller:
>> #interrupt-cells: 00000002
>>
>> Node 0x3010
>> name: 'kpp'
>> compatible: 'fsl,imx6q-kpp' + 'fsl,imx21-kpp'
>> reg: 020b8000.00004000
>> interrupts: 00000000.00000052.00000004
>> clocks: 00000002.0000003e
>> status: 'disabled'
>>
>> Node 0x30a8
>> name: 'wdog'
>> compatible: 'fsl,imx6q-wdt' + 'fsl,imx21-wdt'
>> reg: 020bc000.00004000
>> interrupts: 00000000.00000050.00000004
>> clocks: 00000002.00000000
>>
>> Node 0x3128
>> name: 'wdog'
>> compatible: 'fsl,imx6q-wdt' + 'fsl,imx21-wdt'
>> reg: 020c0000.00004000
>> interrupts: 00000000.00000051.00000004
>> clocks: 00000002.00000000
>> status: 'disabled'
>>
>> Node 0x31c0
>> name: 'ccm'
>> compatible: 'fsl,imx6q-ccm'
>> reg: 020c4000.00004000
>> interrupts:
>> 00000000.00000057.00000004.00000000.00000058.00000004
>> #clock-cells: 00000001
>> linux,phandle: 00000002
>> phandle: 00000002
>>
>> Node 0x325c
>> name: 'anatop'
>> compatible: 'fsl,imx6q-anatop' + 'syscon' + 'simple-bus'
>> reg: 020c8000.00001000
>> interrupts:
>> 00000000.00000031.00000004.00000000.00000036.00000004.00000000.0000007f.00000004
>> linux,phandle: 00000010
>> phandle: 00000010
>>
>> Node 0x3304
>> name: 'regulator-1p1'
>> compatible: 'fsl,anatop-regulator'
>> regulator-name: 'vdd1p1'
>> regulator-min-microvolt: 000c3500
>> regulator-max-microvolt: 0014fb18
>> regulator-always-on:
>> anatop-reg-offset: 00000110
>> anatop-vol-bit-shift: 00000008
>> anatop-vol-bit-width: 00000005
>> anatop-min-bit-val: 00000004
>> anatop-min-voltage: 000c3500
>> anatop-max-voltage: 0014fb18
>>
>> Node 0x33e0
>> name: 'regulator-3p0'
>> compatible: 'fsl,anatop-regulator'
>> regulator-name: 'vdd3p0'
>> regulator-min-microvolt: 002ab980
>> regulator-max-microvolt: 003010b0
>> regulator-always-on:
>> anatop-reg-offset: 00000120
>> anatop-vol-bit-shift: 00000008
>> anatop-vol-bit-width: 00000005
>> anatop-min-bit-val: 00000000
>> anatop-min-voltage: 00280de8
>> anatop-max-voltage: 0033e140
>>
>> Node 0x34bc
>> name: 'regulator-2p5'
>> compatible: 'fsl,anatop-regulator'
>> regulator-name: 'vdd2p5'
>> regulator-min-microvolt: 001e8480
>> regulator-max-microvolt: 0029f630
>> regulator-always-on:
>> anatop-reg-offset: 00000130
>> anatop-vol-bit-shift: 00000008
>> anatop-vol-bit-width: 00000005
>> anatop-min-bit-val: 00000000
>> anatop-min-voltage: 001e8480
>> anatop-max-voltage: 0029f630
>>
>> Node 0x3598
>> name: 'regulator-vddcore'
>> compatible: 'fsl,anatop-regulator'
>> regulator-name: 'vddarm'
>> regulator-min-microvolt: 000b1008
>> regulator-max-microvolt: 00162010
>> regulator-always-on:
>> anatop-reg-offset: 00000140
>> anatop-vol-bit-shift: 00000000
>> anatop-vol-bit-width: 00000005
>> anatop-delay-reg-offset: 00000170
>> anatop-delay-bit-shift: 00000018
>> anatop-delay-bit-width: 00000002
>> anatop-min-bit-val: 00000001
>> anatop-min-voltage: 000b1008
>> anatop-max-voltage: 00162010
>> linux,phandle: 00000042
>> phandle: 00000042
>>
>> Node 0x36c8
>> name: 'regulator-vddpu'
>> compatible: 'fsl,anatop-regulator'
>> regulator-name: 'vddpu'
>> regulator-min-microvolt: 000b1008
>> regulator-max-microvolt: 00162010
>> regulator-enable-ramp-delay: 00000096
>> anatop-reg-offset: 00000140
>> anatop-vol-bit-shift: 00000009
>> anatop-vol-bit-width: 00000005
>> anatop-delay-reg-offset: 00000170
>> anatop-delay-bit-shift: 0000001a
>> anatop-delay-bit-width: 00000002
>> anatop-min-bit-val: 00000001
>> anatop-min-voltage: 000b1008
>> anatop-max-voltage: 00162010
>> linux,phandle: 00000013
>> phandle: 00000013
>>
>> Node 0x37f8
>> name: 'regulator-vddsoc'
>> compatible: 'fsl,anatop-regulator'
>> regulator-name: 'vddsoc'
>> regulator-min-microvolt: 000b1008
>> regulator-max-microvolt: 00162010
>> regulator-always-on:
>> anatop-reg-offset: 00000140
>> anatop-vol-bit-shift: 00000012
>> anatop-vol-bit-width: 00000005
>> anatop-delay-reg-offset: 00000170
>> anatop-delay-bit-shift: 0000001c
>> anatop-delay-bit-width: 00000002
>> anatop-min-bit-val: 00000001
>> anatop-min-voltage: 000b1008
>> anatop-max-voltage: 00162010
>> linux,phandle: 00000043
>> phandle: 00000043
>>
>> Node 0x392c
>> name: 'tempmon'
>> compatible: 'fsl,imx6q-tempmon'
>> interrupts: 00000000.00000031.00000004
>> fsl,tempmon: 00000010
>> fsl,tempmon-data: 00000011
>> clocks: 00000002.000000ac
>>
>> Node 0x39a8
>> name: 'usbphy'
>> compatible: 'fsl,imx6q-usbphy' + 'fsl,imx23-usbphy'
>> reg: 020c9000.00001000
>> interrupts: 00000000.0000002c.00000004
>> clocks: 00000002.000000b6
>> fsl,anatop: 00000010
>> linux,phandle: 0000001d
>> phandle: 0000001d
>>
>> Node 0x3a60
>> name: 'usbphy'
>> compatible: 'fsl,imx6q-usbphy' + 'fsl,imx23-usbphy'
>> reg: 020ca000.00001000
>> interrupts: 00000000.0000002d.00000004
>> clocks: 00000002.000000b7
>> fsl,anatop: 00000010
>> linux,phandle: 00000020
>> phandle: 00000020
>>
>> Node 0x3b18
>> name: 'snvs'
>> compatible: 'fsl,sec-v4.0-mon' + 'syscon' + 'simple-mfd'
>> reg: 020cc000.00004000
>> linux,phandle: 00000012
>> phandle: 00000012
>>
>> Node 0x3b90
>> name: 'snvs-rtc-lp'
>> compatible: 'fsl,sec-v4.0-mon-rtc-lp'
>> regmap: 00000012
>> offset: 00000034
>> interrupts:
>> 00000000.00000013.00000004.00000000.00000014.00000004
>>
>> Node 0x3c0c
>> name: 'snvs-poweroff'
>> compatible: 'syscon-poweroff'
>> regmap: 00000012
>> offset: 00000038
>> mask: 00000060
>> status: 'disabled'
>>
>> Node 0x3c8c
>> name: 'epit'
>> reg: 020d0000.00004000
>> interrupts: 00000000.00000038.00000004
>>
>> Node 0x3cd0
>> name: 'epit'
>> reg: 020d4000.00004000
>> interrupts: 00000000.00000039.00000004
>>
>> Node 0x3d14
>> name: 'src'
>> compatible: 'fsl,imx6q-src' + 'fsl,imx51-src'
>> reg: 020d8000.00004000
>> interrupts:
>> 00000000.0000005b.00000004.00000000.00000060.00000004
>> #reset-cells: 00000001
>> linux,phandle: 0000000e
>> phandle: 0000000e
>>
>> Node 0x3dbc
>> name: 'gpc'
>> compatible: 'fsl,imx6q-gpc'
>> reg: 020dc000.00004000
>> interrupt-controller:
>> #interrupt-cells: 00000003
>> interrupts:
>> 00000000.00000059.00000004.00000000.0000005a.00000004
>> interrupt-parent: 0000000a
>> pu-supply: 00000013
>> clocks:
>> 00000002.0000007a.00000002.0000004a.00000002.00000079.00000002.0000001a.00000002.0000008f.00000002.000000a8
>> #power-domain-cells: 00000001
>> linux,phandle: 00000001
>> phandle: 00000001
>>
>> Node 0x3ed0
>> name: 'iomuxc-gpr'
>> compatible: 'fsl,imx6q-iomuxc-gpr' + 'syscon'
>> reg: 020e0000.00000038
>> linux,phandle: 00000004
>> phandle: 00000004
>>
>> Node 0x3f48
>> name: 'iomuxc'
>> compatible: 'fsl,imx6q-iomuxc'
>> reg: 020e0000.00004000
>> pinctrl-names: 'default'
>> pinctrl-0: 00000014
>>
>> Node 0x3fb4
>> name: 'imx6qdl-wandboard'
>>
>> Node 0x3fcc
>> name: 'audmuxgrp'
>> fsl,pins:
>> 00000274.00000644.00000000.00000004.00000000.000130b0.00000268.00000638.00000000.00000004.00000000.000130b0.0000026c.0000063c.00000000.00000004.00000000.000110b0.00000270.00000640.00000000.00000004.00000000.000130b0
>> linux,phandle: 0000002b
>> phandle: 0000002b
>>
>> Node 0x406c
>> name: 'enetgrp'
>> fsl,pins:
>> 000001d0.000004e4.00000840.00000001.00000000.0001b0b0.000001f4.00000508.00000000.00000001.00000000.0001b0b0.00000058.0000036c.00000000.00000001.00000000.0001b0b0.0000005c.00000370.00000000.00000001.00000000.0001b0b0.00000060.00000374.00000000.00000001.00000000.0001b0b0.00000064.00000378.00000000.00000001.00000000.0001b0b0.00000068.0000037c.00000000.00000001.00000000.0001b0b0.00000074.00000388.00000000.00000001.00000000.0001b0b0.000001d4.000004e8.00000000.00000001.00000000.0001b0b0.00000084.00000398.00000844.00000001.00000000.0001b0b0.00000070.00000384.00000848.00000001.00000000.0001b0b0.00000078.0000038c.0000084c.00000001.00000000.0001b0b0.0000007c.00000390.00000850.00000001.00000000.0001b0b0.00000080.00000394.00000854.00000001.00000000.0001b0b0.0000006c.00000380.00000858.00000001.00000000.0001b0b0.00000248.00000618.0000083c.00000002.00000001.4001b0a8.00000230.00000600.0000003c.00000011.ff000609.000000b1
>> linux,phandle: 00000022
>> phandle: 00000022
>>
>> Node 0x4240
>> name: 'i2c1grp'
>> fsl,pins:
>> 000000a4.000003b8.00000898.00000006.00000000.4001b8b1.000000c4.000003d8.0000089c.00000001.00000000.4001b8b1
>> linux,phandle: 00000027
>> phandle: 00000027
>>
>> Node 0x42ac
>> name: 'i2c2grp'
>> fsl,pins:
>> 00000210.000005e0.000008a0.00000004.00000001.4001b8b1.00000214.000005e4.000008a4.00000004.00000001.4001b8b1
>> linux,phandle: 00000028
>> phandle: 00000028
>>
>> Node 0x4318
>> name: 'spdifgrp'
>> fsl,pins:
>> 000001e4.000004f8.00000000.00000003.00000000.0001b0b0
>> linux,phandle: 0000000c
>> phandle: 0000000c
>>
>> Node 0x4370
>> name: 'uart1grp'
>> fsl,pins:
>> 00000280.00000650.00000000.00000003.00000000.0001b0b1.00000284.00000654.00000920.00000003.00000001.0001b0b1
>> linux,phandle: 0000000d
>> phandle: 0000000d
>>
>> Node 0x43e0
>> name: 'uart3grp'
>> fsl,pins:
>> 000000b4.000003c8.00000000.00000002.00000000.0001b0b1.000000b8.000003cc.00000930.00000002.00000001.0001b0b1.000000ac.000003c0.00000000.00000002.00000000.0001b0b1.000000b0.000003c4.0000092c.00000002.00000001.0001b0b1
>> linux,phandle: 00000030
>> phandle: 00000030
>>
>> Node 0x4480
>> name: 'usbotggrp'
>> fsl,pins:
>> 00000224.000005f4.00000004.00000003.ff0d0101.00017059
>> linux,phandle: 0000001f
>> phandle: 0000001f
>>
>> Node 0x44d8
>> name: 'usdhc1grp'
>> fsl,pins:
>> 00000348.00000730.00000000.00000000.00000000.00017059.00000350.00000738.00000000.00000000.00000000.00010059.00000340.00000728.00000000.00000000.00000000.00017059.0000033c.00000724.00000000.00000000.00000000.00017059.0000034c.00000734.00000000.00000000.00000000.00017059.00000344.0000072c.00000000.00000000.00000000.00017059
>> linux,phandle: 00000024
>> phandle: 00000024
>>
>> Node 0x45a8
>> name: 'usdhc2grp'
>> fsl,pins:
>> 00000358.00000740.00000000.00000000.00000000.00017059.00000354.0000073c.00000000.00000000.00000000.00010059.00000054.00000368.00000000.00000000.00000000.00017059.0000004c.00000360.00000000.00000000.00000000.00017059.00000050.00000364.00000000.00000000.00000000.00017059.0000035c.00000744.00000000.00000000.00000000.00017059
>> linux,phandle: 00000025
>> phandle: 00000025
>>
>> Node 0x4678
>> name: 'usdhc3grp'
>> fsl,pins:
>> 000002b8.000006a0.00000000.00000000.00000000.00017059.000002bc.000006a4.00000000.00000000.00000000.00010059.000002c0.000006a8.00000000.00000000.00000000.00017059.000002c4.000006ac.00000000.00000000.00000000.00017059.000002c8.000006b0.00000000.00000000.00000000.00017059.000002cc.000006b4.00000000.00000000.00000000.00017059
>> linux,phandle: 00000026
>> phandle: 00000026
>>
>> Node 0x4748
>> name: 'hoggrp'
>> fsl,pins:
>> 00000220.000005f0.00000000.00000000.00000000.000130b0.00000234.00000604.00000000.00000005.00000000.80000000.00000138.0000044c.00000000.00000005.00000000.80000000.00000290.00000660.00000000.00000005.00000000.0000f0b0.000001e0.000004f4.00000000.00000005.00000000.000000b0.000001ec.00000500.00000000.00000005.00000000.80000000.0000028c.0000065c.00000000.00000005.00000000.0000f0b0.000001f0.00000504.00000000.00000005.00000000.80000000.00000264.00000634.00000000.00000005.00000000.80000000.00000288.00000658.00000000.00000005.00000000.80000000.00000260.00000630.00000000.00000005.00000000.80000000.000000c8.000003dc.00000000.00000005.00000000.80000000
>> linux,phandle: 00000014
>> phandle: 00000014
>>
>> Node 0x48ac
>> name: 'ldb'
>> #address-cells: 00000001
>> #size-cells: 00000000
>> compatible: 'fsl,imx6q-ldb' + 'fsl,imx53-ldb'
>> gpr: 00000004
>> status: 'disabled'
>> clocks:
>> 00000002.00000021.00000002.00000022.00000002.00000027.00000002.00000028.00000002.00000029.00000002.0000002a.00000002.00000087.00000002.00000088
>> clock-names: 'di0_pll' + 'di1_pll' + 'di0_sel' +
>> 'di1_sel' + 'di2_sel' + 'di3_sel' + 'di0' + 'di1'
>>
>> Node 0x49c0
>> name: 'lvds-channel'
>> #address-cells: 00000001
>> #size-cells: 00000000
>> reg: 00000000
>> status: 'disabled'
>>
>> Node 0x4a1c
>> name: 'port'
>> reg: 00000000
>>
>> Node 0x4a38
>> name: 'endpoint'
>> remote-endpoint: 00000015
>> linux,phandle: 00000033
>> phandle: 00000033
>>
>> Node 0x4a80
>> name: 'port'
>> reg: 00000001
>>
>> Node 0x4a9c
>> name: 'endpoint'
>> remote-endpoint: 00000016
>> linux,phandle: 00000037
>> phandle: 00000037
>>
>> Node 0x4ae4
>> name: 'port'
>> reg: 00000002
>>
>> Node 0x4b00
>> name: 'endpoint'
>> remote-endpoint: 00000017
>> linux,phandle: 0000003b
>> phandle: 0000003b
>>
>> Node 0x4b48
>> name: 'port'
>> reg: 00000003
>>
>> Node 0x4b64
>> name: 'endpoint'
>> remote-endpoint: 00000018
>> linux,phandle: 0000003f
>> phandle: 0000003f
>>
>> Node 0x4bb0
>> name: 'lvds-channel'
>> #address-cells: 00000001
>> #size-cells: 00000000
>> reg: 00000001
>> status: 'disabled'
>>
>> Node 0x4c0c
>> name: 'port'
>> reg: 00000000
>>
>> Node 0x4c28
>> name: 'endpoint'
>> remote-endpoint: 00000019
>> linux,phandle: 00000034
>> phandle: 00000034
>>
>> Node 0x4c70
>> name: 'port'
>> reg: 00000001
>>
>> Node 0x4c8c
>> name: 'endpoint'
>> remote-endpoint: 0000001a
>> linux,phandle: 00000038
>> phandle: 00000038
>>
>> Node 0x4cd4
>> name: 'port'
>> reg: 00000002
>>
>> Node 0x4cf0
>> name: 'endpoint'
>> remote-endpoint: 0000001b
>> linux,phandle: 0000003c
>> phandle: 0000003c
>>
>> Node 0x4d38
>> name: 'port'
>> reg: 00000003
>>
>> Node 0x4d54
>> name: 'endpoint'
>> remote-endpoint: 0000001c
>> linux,phandle: 00000040
>> phandle: 00000040
>>
>> Node 0x4da4
>> name: 'dcic'
>> reg: 020e4000.00004000
>> interrupts: 00000000.0000007c.00000004
>>
>> Node 0x4de8
>> name: 'dcic'
>> reg: 020e8000.00004000
>> interrupts: 00000000.0000007d.00000004
>>
>> Node 0x4e2c
>> name: 'sdma'
>> compatible: 'fsl,imx6q-sdma' + 'fsl,imx35-sdma'
>> reg: 020ec000.00004000
>> interrupts: 00000000.00000002.00000004
>> clocks: 00000002.0000009b.00000002.0000009b
>> clock-names: 'ipg' + 'ahb'
>> #dma-cells: 00000003
>> fsl,sdma-ram-script-name: 'imx/sdma/sdma-imx6q.bin'
>> linux,phandle: 0000000b
>> phandle: 0000000b
>>
>> Node 0x4f24
>> name: 'aips-bus'
>> compatible: 'fsl,aips-bus' + 'simple-bus'
>> #address-cells: 00000001
>> #size-cells: 00000001
>> reg: 02100000.00100000
>> ranges:
>>
>> Node 0x4fa0
>> name: 'caam'
>> compatible: 'fsl,sec-v4.0'
>> fsl,sec-era: 00000004
>> #address-cells: 00000001
>> #size-cells: 00000001
>> reg: 02100000.00010000
>> ranges: 00000000.02100000.00010000
>> clocks:
>> 00000002.000000f1.00000002.000000f2.00000002.000000f3.00000002.000000c4
>> clock-names: 'mem' + 'aclk' + 'ipg' + 'emi_slow'
>>
>> Node 0x507c
>> name: 'jr0'
>> compatible: 'fsl,sec-v4.0-job-ring'
>> reg: 00001000.00001000
>> interrupts: 00000000.00000069.00000004
>>
>> Node 0x50e0
>> name: 'jr1'
>> compatible: 'fsl,sec-v4.0-job-ring'
>> reg: 00002000.00001000
>> interrupts: 00000000.0000006a.00000004
>>
>> Node 0x5148
>> name: 'aipstz'
>> reg: 0217c000.00004000
>>
>> Node 0x5174
>> name: 'usb'
>> compatible: 'fsl,imx6q-usb' + 'fsl,imx27-usb'
>> reg: 02184000.00000200
>> interrupts: 00000000.0000002b.00000004
>> clocks: 00000002.000000a2
>> fsl,usbphy: 0000001d
>> fsl,usbmisc: 0000001e.00000000
>> ahb-burst-config: 00000000
>> tx-burst-size-dword: 00000010
>> rx-burst-size-dword: 00000010
>> status: 'okay'
>> pinctrl-names: 'default'
>> pinctrl-0: 0000001f
>> disable-over-current:
>> dr_mode: 'peripheral'
>>
>> Node 0x52a4
>> name: 'usb'
>> compatible: 'fsl,imx6q-usb' + 'fsl,imx27-usb'
>> reg: 02184200.00000200
>> interrupts: 00000000.00000028.00000004
>> clocks: 00000002.000000a2
>> fsl,usbphy: 00000020
>> fsl,usbmisc: 0000001e.00000001
>> dr_mode: 'host'
>> ahb-burst-config: 00000000
>> tx-burst-size-dword: 00000010
>> rx-burst-size-dword: 00000010
>> status: 'okay'
>>
>> Node 0x53a0
>> name: 'usb'
>> compatible: 'fsl,imx6q-usb' + 'fsl,imx27-usb'
>> reg: 02184400.00000200
>> interrupts: 00000000.00000029.00000004
>> clocks: 00000002.000000a2
>> fsl,usbmisc: 0000001e.00000002
>> dr_mode: 'host'
>> ahb-burst-config: 00000000
>> tx-burst-size-dword: 00000010
>> rx-burst-size-dword: 00000010
>> status: 'disabled'
>>
>> Node 0x5490
>> name: 'usb'
>> compatible: 'fsl,imx6q-usb' + 'fsl,imx27-usb'
>> reg: 02184600.00000200
>> interrupts: 00000000.0000002a.00000004
>> clocks: 00000002.000000a2
>> fsl,usbmisc: 0000001e.00000003
>> dr_mode: 'host'
>> ahb-burst-config: 00000000
>> tx-burst-size-dword: 00000010
>> rx-burst-size-dword: 00000010
>> status: 'disabled'
>>
>> Node 0x5580
>> name: 'usbmisc'
>> #index-cells: 00000001
>> compatible: 'fsl,imx6q-usbmisc'
>> reg: 02184800.00000200
>> clocks: 00000002.000000a2
>> linux,phandle: 0000001e
>> phandle: 0000001e
>>
>> Node 0x5614
>> name: 'ethernet'
>> local-mac-address: 001f7bb4.225f
>> compatible: 'fsl,imx6q-fec'
>> reg: 02188000.00004000
>> interrupts-extended:
>> 00000021.00000006.00000004.0000000a.00000000.00000077.00000004
>> clocks:
>> 00000002.00000075.00000002.00000075.00000002.000000be
>> clock-names: 'ipg' + 'ahb' + 'ptp'
>> status: 'okay'
>> pinctrl-names: 'default'
>> pinctrl-0: 00000022
>> phy-mode: 'rgmii'
>> phy-reset-gpios: 00000023.0000001d.00000000
>>
>> Node 0x573c
>> name: 'mlb'
>> reg: 0218c000.00004000
>> interrupts:
>> 00000000.00000035.00000004.00000000.00000075.00000004.00000000.0000007e.00000004
>>
>> Node 0x5798
>> name: 'usdhc'
>> compatible: 'fsl,imx6q-usdhc'
>> reg: 02190000.00004000
>> interrupts: 00000000.00000016.00000004
>> clocks:
>> 00000002.000000a3.00000002.000000a3.00000002.000000a3
>> clock-names: 'ipg' + 'ahb' + 'per'
>> bus-width: 00000004
>> status: 'okay'
>> pinctrl-names: 'default'
>> pinctrl-0: 00000024
>> cd-gpios: 00000021.00000002.00000001
>>
>> Node 0x5894
>> name: 'usdhc'
>> compatible: 'fsl,imx6q-usdhc'
>> reg: 02194000.00004000
>> interrupts: 00000000.00000017.00000004
>> clocks:
>> 00000002.000000a4.00000002.000000a4.00000002.000000a4
>> clock-names: 'ipg' + 'ahb' + 'per'
>> bus-width: 00000004
>> status: 'okay'
>> pinctrl-names: 'default'
>> pinctrl-0: 00000025
>>
>> Node 0x5978
>> name: 'usdhc'
>> compatible: 'fsl,imx6q-usdhc'
>> reg: 02198000.00004000
>> interrupts: 00000000.00000018.00000004
>> clocks:
>> 00000002.000000a5.00000002.000000a5.00000002.000000a5
>> clock-names: 'ipg' + 'ahb' + 'per'
>> bus-width: 00000004
>> status: 'okay'
>> pinctrl-names: 'default'
>> pinctrl-0: 00000026
>> cd-gpios: 00000023.00000009.00000001
>>
>> Node 0x5a74
>> name: 'usdhc'
>> compatible: 'fsl,imx6q-usdhc'
>> reg: 0219c000.00004000
>> interrupts: 00000000.00000019.00000004
>> clocks:
>> 00000002.000000a6.00000002.000000a6.00000002.000000a6
>> clock-names: 'ipg' + 'ahb' + 'per'
>> bus-width: 00000004
>> status: 'disabled'
>>
>> Node 0x5b38
>> name: 'i2c'
>> #address-cells: 00000001
>> #size-cells: 00000000
>> compatible: 'fsl,imx6q-i2c' + 'fsl,imx21-i2c'
>> reg: 021a0000.00004000
>> interrupts: 00000000.00000024.00000004
>> clocks: 00000002.0000007d
>> status: 'okay'
>> clock-frequency: 000186a0
>> pinctrl-names: 'default'
>> pinctrl-0: 00000027
>> linux,phandle: 00000005
>> phandle: 00000005
>>
>> Node 0x5c40
>> name: 'i2c'
>> #address-cells: 00000001
>> #size-cells: 00000000
>> compatible: 'fsl,imx6q-i2c' + 'fsl,imx21-i2c'
>> reg: 021a4000.00004000
>> interrupts: 00000000.00000025.00000004
>> clocks: 00000002.0000007e
>> status: 'okay'
>> clock-frequency: 000186a0
>> pinctrl-names: 'default'
>> pinctrl-0: 00000028
>>
>> Node 0x5d24
>> name: 'sgtl5000'
>> compatible: 'fsl,sgtl5000'
>> reg: 0000000a
>> clocks: 00000002.000000c9
>> VDDA-supply: 00000029
>> VDDIO-supply: 0000002a
>> linux,phandle: 0000004c
>> phandle: 0000004c
>>
>> Node 0x5dbc
>> name: 'i2c'
>> #address-cells: 00000001
>> #size-cells: 00000000
>> compatible: 'fsl,imx6q-i2c' + 'fsl,imx21-i2c'
>> reg: 021a8000.00004000
>> interrupts: 00000000.00000026.00000004
>> clocks: 00000002.0000007f
>> status: 'disabled'
>>
>> Node 0x5e74
>> name: 'romcp'
>> reg: 021ac000.00004000
>>
>> Node 0x5ea0
>> name: 'mmdc'
>> compatible: 'fsl,imx6q-mmdc'
>> reg: 021b0000.00004000
>>
>> Node 0x5ee8
>> name: 'mmdc'
>> reg: 021b4000.00004000
>>
>> Node 0x5f14
>> name: 'weim'
>> compatible: 'fsl,imx6q-weim'
>> reg: 021b8000.00004000
>> interrupts: 00000000.0000000e.00000004
>> clocks: 00000002.000000c4
>>
>> Node 0x5f88
>> name: 'ocotp'
>> compatible: 'fsl,imx6q-ocotp' + 'syscon'
>> reg: 021bc000.00004000
>> linux,phandle: 00000011
>> phandle: 00000011
>>
>> Node 0x5ff8
>> name: 'tzasc'
>> reg: 021d0000.00004000
>> interrupts: 00000000.0000006c.00000004
>>
>> Node 0x603c
>> name: 'tzasc'
>> reg: 021d4000.00004000
>> interrupts: 00000000.0000006d.00000004
>>
>> Node 0x6080
>> name: 'audmux'
>> compatible: 'fsl,imx6q-audmux' + 'fsl,imx31-audmux'
>> reg: 021d8000.00004000
>> status: 'okay'
>> pinctrl-names: 'default'
>> pinctrl-0: 0000002b
>>
>> Node 0x6114
>> name: 'mipi'
>> reg: 021dc000.00004000
>>
>> Node 0x6140
>> name: 'mipi'
>> #address-cells: 00000001
>> #size-cells: 00000000
>> reg: 021e0000.00004000
>> status: 'disabled'
>>
>> Node 0x61a0
>> name: 'ports'
>> #address-cells: 00000001
>> #size-cells: 00000000
>>
>> Node 0x61cc
>> name: 'port'
>> reg: 00000000
>>
>> Node 0x61e8
>> name: 'endpoint'
>> remote-endpoint: 0000002c
>> linux,phandle: 00000032
>> phandle: 00000032
>>
>> Node 0x6230
>> name: 'port'
>> reg: 00000001
>>
>> Node 0x624c
>> name: 'endpoint'
>> remote-endpoint: 0000002d
>> linux,phandle: 00000036
>> phandle: 00000036
>>
>> Node 0x6294
>> name: 'port'
>> reg: 00000002
>>
>> Node 0x62b0
>> name: 'endpoint'
>> remote-endpoint: 0000002e
>> linux,phandle: 0000003a
>> phandle: 0000003a
>>
>> Node 0x62f8
>> name: 'port'
>> reg: 00000003
>>
>> Node 0x6314
>> name: 'endpoint'
>> remote-endpoint: 0000002f
>> linux,phandle: 0000003e
>> phandle: 0000003e
>>
>> Node 0x6364
>> name: 'vdoa'
>> reg: 021e4000.00004000
>> interrupts: 00000000.00000012.00000004
>>
>> Node 0x63a8
>> name: 'serial'
>> compatible: 'fsl,imx6q-uart' + 'fsl,imx21-uart'
>> reg: 021e8000.00004000
>> interrupts: 00000000.0000001b.00000004
>> clocks: 00000002.000000a0.00000002.000000a1
>> clock-names: 'ipg' + 'per'
>> dmas:
>> 0000000b.0000001b.00000004.00000000.0000000b.0000001c.00000004.00000000
>> dma-names: 'rx' + 'tx'
>> status: 'disabled'
>>
>> Node 0x64a0
>> name: 'serial'
>> compatible: 'fsl,imx6q-uart' + 'fsl,imx21-uart'
>> reg: 021ec000.00004000
>> interrupts: 00000000.0000001c.00000004
>> clocks: 00000002.000000a0.00000002.000000a1
>> clock-names: 'ipg' + 'per'
>> dmas:
>> 0000000b.0000001d.00000004.00000000.0000000b.0000001e.00000004.00000000
>> dma-names: 'rx' + 'tx'
>> status: 'okay'
>> pinctrl-names: 'default'
>> pinctrl-0: 00000030
>> fsl,uart-has-rtscts:
>>
>> Node 0x65c4
>> name: 'serial'
>> compatible: 'fsl,imx6q-uart' + 'fsl,imx21-uart'
>> reg: 021f0000.00004000
>> interrupts: 00000000.0000001d.00000004
>> clocks: 00000002.000000a0.00000002.000000a1
>> clock-names: 'ipg' + 'per'
>> dmas:
>> 0000000b.0000001f.00000004.00000000.0000000b.00000020.00000004.00000000
>> dma-names: 'rx' + 'tx'
>> status: 'disabled'
>>
>> Node 0x66bc
>> name: 'serial'
>> compatible: 'fsl,imx6q-uart' + 'fsl,imx21-uart'
>> reg: 021f4000.00004000
>> interrupts: 00000000.0000001e.00000004
>> clocks: 00000002.000000a0.00000002.000000a1
>> clock-names: 'ipg' + 'per'
>> dmas:
>> 0000000b.00000021.00000004.00000000.0000000b.00000022.00000004.00000000
>> dma-names: 'rx' + 'tx'
>> status: 'disabled'
>>
>> Node 0x67b8
>> name: 'ipu'
>> #address-cells: 00000001
>> #size-cells: 00000000
>> compatible: 'fsl,imx6q-ipu'
>> reg: 02400000.00400000
>> interrupts:
>> 00000000.00000006.00000004.00000000.00000005.00000004
>> clocks:
>> 00000002.00000082.00000002.00000083.00000002.00000084
>> clock-names: 'bus' + 'di0' + 'di1'
>> resets: 0000000e.00000002
>>
>> Node 0x6890
>> name: 'port'
>> reg: 00000000
>>
>> Node 0x68b0
>> name: 'port'
>> reg: 00000001
>>
>> Node 0x68d0
>> name: 'port'
>> #address-cells: 00000001
>> #size-cells: 00000000
>> reg: 00000002
>> linux,phandle: 00000044
>> phandle: 00000044
>>
>> Node 0x692c
>> name: 'disp0-endpoint'
>>
>> Node 0x6944
>> name: 'hdmi-endpoint'
>> remote-endpoint: 00000031
>> linux,phandle: 00000006
>> phandle: 00000006
>>
>> Node 0x698c
>> name: 'mipi-endpoint'
>> remote-endpoint: 00000032
>> linux,phandle: 0000002c
>> phandle: 0000002c
>>
>> Node 0x69d4
>> name: 'lvds0-endpoint'
>> remote-endpoint: 00000033
>> linux,phandle: 00000015
>> phandle: 00000015
>>
>> Node 0x6a1c
>> name: 'lvds1-endpoint'
>> remote-endpoint: 00000034
>> linux,phandle: 00000019
>> phandle: 00000019
>>
>> Node 0x6a68
>> name: 'port'
>> #address-cells: 00000001
>> #size-cells: 00000000
>> reg: 00000003
>> linux,phandle: 00000045
>> phandle: 00000045
>>
>> Node 0x6ac4
>> name: 'disp1-endpoint'
>>
>> Node 0x6adc
>> name: 'hdmi-endpoint'
>> remote-endpoint: 00000035
>> linux,phandle: 00000007
>> phandle: 00000007
>>
>> Node 0x6b24
>> name: 'mipi-endpoint'
>> remote-endpoint: 00000036
>> linux,phandle: 0000002d
>> phandle: 0000002d
>>
>> Node 0x6b6c
>> name: 'lvds0-endpoint'
>> remote-endpoint: 00000037
>> linux,phandle: 00000016
>> phandle: 00000016
>>
>> Node 0x6bb4
>> name: 'lvds1-endpoint'
>> remote-endpoint: 00000038
>> linux,phandle: 0000001a
>> phandle: 0000001a
>>
>> Node 0x6c04
>> name: 'sram'
>> compatible: 'mmio-sram'
>> reg: 00900000.00040000
>> clocks: 00000002.0000008e
>> linux,phandle: 0000000f
>> phandle: 0000000f
>>
>> Node 0x6c7c
>> name: 'sata'
>> compatible: 'fsl,imx6q-ahci'
>> reg: 02200000.00004000
>> interrupts: 00000000.00000027.00000004
>> clocks:
>> 00000002.0000009a.00000002.000000bb.00000002.00000069
>> clock-names: 'sata' + 'sata_ref' + 'ahb'
>> status: 'okay'
>>
>> Node 0x6d34
>> name: 'gpu'
>> compatible: 'vivante,gc'
>> reg: 02204000.00004000
>> interrupts: 00000000.0000000b.00000004
>> clocks: 00000002.0000008f.00000002.00000079
>> clock-names: 'bus' + 'core'
>> power-domains: 00000001.00000001
>> linux,phandle: 0000004a
>> phandle: 0000004a
>>
>> Node 0x6df8
>> name: 'ipu'
>> #address-cells: 00000001
>> #size-cells: 00000000
>> compatible: 'fsl,imx6q-ipu'
>> reg: 02800000.00400000
>> interrupts:
>> 00000000.00000008.00000004.00000000.00000007.00000004
>> clocks:
>> 00000002.00000085.00000002.00000086.00000002.00000089
>> clock-names: 'bus' + 'di0' + 'di1'
>> resets: 0000000e.00000004
>>
>> Node 0x6ed0
>> name: 'port'
>> reg: 00000000
>>
>> Node 0x6ef0
>> name: 'port'
>> reg: 00000001
>>
>> Node 0x6f10
>> name: 'port'
>> #address-cells: 00000001
>> #size-cells: 00000000
>> reg: 00000002
>> linux,phandle: 00000046
>> phandle: 00000046
>>
>> Node 0x6f6c
>> name: 'disp0-endpoint'
>>
>> Node 0x6f84
>> name: 'hdmi-endpoint'
>> remote-endpoint: 00000039
>> linux,phandle: 00000008
>> phandle: 00000008
>>
>> Node 0x6fcc
>> name: 'mipi-endpoint'
>> remote-endpoint: 0000003a
>> linux,phandle: 0000002e
>> phandle: 0000002e
>>
>> Node 0x7014
>> name: 'lvds0-endpoint'
>> remote-endpoint: 0000003b
>> linux,phandle: 00000017
>> phandle: 00000017
>>
>> Node 0x705c
>> name: 'lvds1-endpoint'
>> remote-endpoint: 0000003c
>> linux,phandle: 0000001b
>> phandle: 0000001b
>>
>> Node 0x70a8
>> name: 'port'
>> #address-cells: 00000001
>> #size-cells: 00000000
>> reg: 00000003
>> linux,phandle: 00000047
>> phandle: 00000047
>>
>> Node 0x7104
>> name: 'hdmi-endpoint'
>> remote-endpoint: 0000003d
>> linux,phandle: 00000009
>> phandle: 00000009
>>
>> Node 0x714c
>> name: 'mipi-endpoint'
>> remote-endpoint: 0000003e
>> linux,phandle: 0000002f
>> phandle: 0000002f
>>
>> Node 0x7194
>> name: 'lvds0-endpoint'
>> remote-endpoint: 0000003f
>> linux,phandle: 00000018
>> phandle: 00000018
>>
>> Node 0x71dc
>> name: 'lvds1-endpoint'
>> remote-endpoint: 00000040
>> linux,phandle: 0000001c
>> phandle: 0000001c
>>
>> Node 0x7230
>> name: 'cpus'
>> #address-cells: 00000001
>> #size-cells: 00000000
>>
>> Node 0x725c
>> name: 'cpu'
>> compatible: 'arm,cortex-a9'
>> device_type: 'cpu'
>> reg: 00000000
>> next-level-cache: 00000041
>> operating-points:
>> 00124f80.00137478.000f32a0.001312d0.000d0020.001312d0.000c15c0.0011edd8.00060ae0.000ee098
>> fsl,soc-operating-points:
>> 00124f80.00137478.000f32a0.001312d0.000d0020.001312d0.000c15c0.0011edd8.00060ae0.0011edd8
>> clock-latency: 0000ee6c
>> clocks:
>> 00000002.00000068.00000002.00000006.00000002.00000010.00000002.00000011.00000002.000000aa
>> clock-names: 'arm' + 'pll2_pfd2_396m' + 'step' + 'pll1_sw' +
>> 'pll1_sys'
>> arm-supply: 00000042
>> pu-supply: 00000013
>> soc-supply: 00000043
>>
>> Node 0x73cc
>> name: 'cpu'
>> compatible: 'arm,cortex-a9'
>> device_type: 'cpu'
>> reg: 00000001
>> next-level-cache: 00000041
>>
>> Node 0x7428
>> name: 'cpu'
>> compatible: 'arm,cortex-a9'
>> device_type: 'cpu'
>> reg: 00000002
>> next-level-cache: 00000041
>>
>> Node 0x7484
>> name: 'cpu'
>> compatible: 'arm,cortex-a9'
>> device_type: 'cpu'
>> reg: 00000003
>> next-level-cache: 00000041
>>
>> Node 0x74e4
>> name: 'display-subsystem'
>> compatible: 'fsl,imx-display-subsystem'
>> ports: 00000044.00000045.00000046.00000047
>>
>> Node 0x7544
>> name: 'gpu-subsystem'
>> compatible: 'fsl,imx-gpu-subsystem'
>> cores: 00000048.00000049.0000004a
>>
>> Node 0x7598
>> name: 'regulators'
>> compatible: 'simple-bus'
>> #address-cells: 00000001
>> #size-cells: 00000000
>>
>> Node 0x75e0
>> name: 'regulator'
>> compatible: 'regulator-fixed'
>> reg: 00000000
>> regulator-name: '2P5V'
>> regulator-min-microvolt: 002625a0
>> regulator-max-microvolt: 002625a0
>> regulator-always-on:
>> linux,phandle: 00000029
>> phandle: 00000029
>>
>> Node 0x7680
>> name: 'regulator'
>> compatible: 'regulator-fixed'
>> reg: 00000001
>> regulator-name: '3P3V'
>> regulator-min-microvolt: 00325aa0
>> regulator-max-microvolt: 00325aa0
>> regulator-always-on:
>> linux,phandle: 0000002a
>> phandle: 0000002a
>>
>> Node 0x7724
>> name: 'sound'
>> compatible: 'fsl,imx6-wandboard-sgtl5000' +
>> 'fsl,imx-audio-sgtl5000'
>> model: 'imx6-wandboard-sgtl5000'
>> ssi-controller: 0000004b
>> audio-codec: 0000004c
>> audio-routing: 'MIC_IN' + 'Mic Jack' + 'Mic Jack' + 'Mic Bias' +
>> 'Headphone Jack' + 'HP_OUT'
>> mux-int-port: 00000001
>> mux-ext-port: 00000003
>>
>> Node 0x781c
>> name: 'sound-spdif'
>> compatible: 'fsl,imx-audio-spdif'
>> model: 'imx-spdif'
>> spdif-controller: 0000004d
>> spdif-out:
>
>
--
Joe Gidi
[email protected]
"You cannot buy skill." -- Ross Seyfried
