>Synopsis:      I can't set permanent arp entries in the ERL router
>Category:      system
>Environment:
        System      : OpenBSD 6.0
        Details     : OpenBSD 6.0-current (GENERIC) #27: Mon Sep 12 00:55:34 
UTC 2016
                         visa@octeon:/usr/src/sys/arch/octeon/compile/GENERIC
 
        Architecture: OpenBSD.octeon
        Machine     : octeon
>Description:
 
Hello. I'm trying to set permament arp entries in my router.
This happens in OpenBSD 6.0-release. I have installed -current
and the problem is still happening.
 
I have tried this in my amd64 machine and all works fine there,
so I suppose this is a bug (I also asked in #openbsd first)
 
This is a fresh -current installation. It happened exactly
the same in my previous 6.0-release installation.
 
mac adddresses are spoofed for privacy.
 
>How-To-Repeat:

# arp -Fs 192.168.1.50 00:25:90:a2:aa:91
192.168.1.50 (192.168.1.50) deleted
arp: writing to routing socket: File exists
 
# arp -a
Host                                 Ethernet Address   Netif Expire     Flags
192.168.1.1                          44:d9:e7:9f:0d:1b cnmac1 permanent  l
192.168.1.50                         00:25:90:a2:aa:91 cnmac1 20m0s
 
# arp -d 192.168.1.50
192.168.1.50 (192.168.1.50) deleted
# arp -s 192.168.1.50 00:25:90:a2:aa:12
arp: writing to routing socket: File exists
 
# arp -a
Host                                 Ethernet Address   Netif Expire     Flags
192.168.1.1                          44:d9:e7:9f:0d:1b cnmac1 permanent  l
192.168.1.50                         00:25:90:a2:aa:91 cnmac1 19m47s
 
dmesg:
Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2016 OpenBSD. All rights reserved.  https://www.OpenBSD.org
 
OpenBSD 6.0-current (GENERIC) #27: Mon Sep 12 00:55:34 UTC 2016
    visa@octeon:/usr/src/sys/arch/octeon/compile/GENERIC
real mem = 536870912 (512MB)
avail mem = 524369920 (500MB)
warning: no entropy supplied by boot loader
mainbus0 at root
cpu0 at mainbus0: Cavium OCTEON CPU rev 0.1 500 MHz, Software FP emulation
cpu0: cache L1-I 32KB 4 way D 8KB 64 way, L2 128KB 8 way
clock0 at mainbus0: int 5
iobus0 at mainbus0
dwctwo0 at iobus0 base 0x1180068000000 irq 56
usb0 at dwctwo0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Octeon DWC2 root hub" rev 2.00/1.00 
addr 1
octrng0 at iobus0 base 0x1400000000000 irq 0
cn30xxgmx0 at iobus0 base 0x1180008000000
cnmac0 at cn30xxgmx0: RGMII, address 44:d9:e7:9f:0d:3c
atphy0 at cnmac0 phy 7: AR8035 10/100/1000 PHY, rev. 2
cnmac1 at cn30xxgmx0: RGMII, address 44:d9:e7:9f:0d:3d
atphy1 at cnmac1 phy 6: AR8035 10/100/1000 PHY, rev. 2
cnmac2 at cn30xxgmx0: RGMII, address 44:d9:e7:9f:0d:3e
atphy2 at cnmac2 phy 5: AR8035 10/100/1000 PHY, rev. 2
uartbus0 at mainbus0
com0 at uartbus0 base 0x1180000000800 irq 34: ns16550a, 64 byte fifo
com0: console
com1 at uartbus0 base 0x1180000000c00 irq 35: ns16550a, 64 byte fifo
/dev/ksyms: Symbol table not valid.
umass0 at uhub0 port 1 configuration 1 interface 0 "SanDisk Cruzer Fit" rev 
2.00/1.27 addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SanDisk, Cruzer Fit, 1.27> SCSI4 0/direct 
removable serial.07815571020310117511
sd0: 14907MB, 512 bytes/sector, 30529536 sectors
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
boot device: sd0
root on sd0a (7578e614430eb5aa.a) swap on sd0b dump on sd0b
WARNING: No TOD clock, believing file system.
WARNING: CHECK AND RESET THE DATE!
 
usbdevs:
Controller /dev/usb0:
addr 1: high speed, self powered, config 1, DWC2 root hub(0x0000), 
Octeon(0x0000), rev 1.00
 port 1 addr 2: high speed, power 200 mA, config 1, Cruzer Fit(0x5571), 
SanDisk(0x0781), rev 1.27, iSerialNumber 4C530001020310117511

Reply via email to