Synopsis: relayd terminates abnormal
Category:
Environment:
System : OpenBSD 6.1
Details : OpenBSD 6.1 (GENERIC.MP) #20: Sat Apr 1 13:45:56 MDT 2017
[email protected]:/usr/src/sys/arch/amd64/compile/GENERIC.MP
Architecture: OpenBSD.amd64
Machine : amd64
Description:
Relayd terminates without any reason.
Following relays.conf I have:
————————cut------------------------
log all
table <fw> { 192.168.78.124, 192.168.78.125 }
table <dns> { 10.78.2.1, 10.78.2.2, 10.78.2.3 }
tcp protocol generic {
tcp { nodelay, sack, socket buffer 65536, backlog 1024 }
}
dns protocol vps_dns { }
relay tor {
listen on 192.168.78.122 port 9050
protocol generic
forward to <fw> port 9050 mode roundrobin check tcp
}
relay dns {
listen on 127.0.0.1 port 5354
protocol vps_dns
forward to <dns> port 53 mode roundrobin check tcp
}
————————end of config—————————————
192.168.78.x is an internal network, home LAN.
10.78.x.x seen in config are remote, via iBGP, addresses configured on
lo1. BGP traffic flows protected by IPSec:
gif+vether+bridge. Remote machines are OpenBSD 6.0, stable via
mtire.org.
This config is not new and been working during OpenBSD 6.0.
Logs from relayd seen in syslog:
Apr 13 15:49:28 fw1 relayd[86677]: host 10.78.2.3, check tcp (35ms,tcp
connect ok), state up -> up, availability 100.00%
Apr 13 15:49:28 fw1 relayd[86677]: host 10.78.2.2, check tcp (41ms,tcp
connect ok), state up -> up, availability 100.00%
Apr 13 15:49:28 fw1 relayd[86677]: host 10.78.2.1, check tcp (59ms,tcp
connect ok), state up -> up, availability 100.00%
Apr 13 15:49:38 fw1 relayd[86677]: host 192.168.78.124, check tcp
(0ms,tcp connect ok), state up -> up, availability 100.00%
Apr 13 15:49:38 fw1 relayd[86677]: host 192.168.78.125, check tcp
(1ms,tcp connect ok), state up -> up, availability 100.00%
Apr 13 15:49:38 fw1 relayd[86677]: host 10.78.2.3, check tcp (35ms,tcp
connect ok), state up -> up, availability 100.00%
Apr 13 15:49:38 fw1 relayd[86677]: host 10.78.2.2, check tcp (41ms,tcp
connect ok), state up -> up, availability 100.00%
Apr 13 15:49:38 fw1 relayd[86677]: host 10.78.2.1, check tcp (60ms,tcp
connect ok), state up -> up, availability 100.00%
Apr 13 15:49:42 fw1 relayd[86677]: hce exiting, pid 86677 Apr 13
15:49:42 fw1 relayd[95323]: ca exiting, pid 95323
Apr 13 15:49:42 fw1 relayd[72953]: ca exiting, pid 72953
Apr 13 15:49:42 fw1 relayd[81673]: ca exiting, pid 81673
Apr 13 15:49:42 fw1 relayd[41926]: pfe exiting, pid 41926
Apr 13 15:49:42 fw1 relayd[52954]: parent terminating, pid 52954
’log all’ in config been activate to catch what is going on. Looks like
without any success.
login.conf been modded to give more fds(in case):
relayd:\
:maxproc-max=31:\
:openfiles-cur=65536:\
:openfiles-max=65536:\
:tc=daemon:
How-To-Repeat:
Not sure here. Maybe have the same setup listening on internal network
Fix:
Not known, but I’m happy to assist and test.
dmesg:
OpenBSD 6.1 (GENERIC.MP) #20: Sat Apr 1 13:45:56 MDT 2017
[email protected]:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 4278124544 (4079MB)
avail mem = 4143792128 (3951MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.4 @ 0xe0010 (248 entries)
bios0: vendor Phoenix Technologies LTD version "6.00" date 04/05/2016
bios0: VMware, Inc. VMware Virtual Platform
acpi0 at bios0: rev 2
acpi0: sleep states S0 S1 S4 S5
acpi0: tables DSDT FACP BOOT APIC MCFG SRAT HPET WAET
acpi0: wakeup devices PCI0(S3) USB_(S1) P2P0(S3) S1F0(S3) S2F0(S3) S8F0(S3)
S16F(S3) S17F(S3) S18F(S3) S22F(S3) S23F(S3) S24F(S3) S25F(S3) PE40(S3)
S1F0(S3) PE50(S3) [...]
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Xeon(R) CPU L5640 @ 2.27GHz, 1595.55 MHz
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,MMX,FXSR,SSE,SSE2,SS,HTT,SSE3,PCLMUL,SSSE3,CX16,SSE4.1,SSE4.2,POPCNT,AES,HV,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,SENSOR,ARAT
cpu0: 256KB 64b/line 8-way L2 cache
cpu0: TSC frequency 1595553840 Hz
cpu0: smt 0, core 0, package 0
mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
cpu0: apic clock running at 65MHz
cpu1 at mainbus0: apid 1 (application processor)
cpu1: Intel(R) Xeon(R) CPU L5640 @ 2.27GHz, 1595.66 MHz
cpu1:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,MMX,FXSR,SSE,SSE2,SS,HTT,SSE3,PCLMUL,SSSE3,CX16,SSE4.1,SSE4.2,POPCNT,AES,HV,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,SENSOR,ARAT
cpu1: 256KB 64b/line 8-way L2 cache
cpu1: smt 0, core 1, package 0
cpu2 at mainbus0: apid 2 (application processor)
cpu2: Intel(R) Xeon(R) CPU L5640 @ 2.27GHz, 1595.79 MHz
cpu2:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,MMX,FXSR,SSE,SSE2,SS,HTT,SSE3,PCLMUL,SSSE3,CX16,SSE4.1,SSE4.2,POPCNT,AES,HV,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,SENSOR,ARAT
cpu2: 256KB 64b/line 8-way L2 cache
cpu2: smt 0, core 0, package 1
cpu3 at mainbus0: apid 3 (application processor)
cpu3: Intel(R) Xeon(R) CPU L5640 @ 2.27GHz, 1595.67 MHz
cpu3:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,MMX,FXSR,SSE,SSE2,SS,HTT,SSE3,PCLMUL,SSSE3,CX16,SSE4.1,SSE4.2,POPCNT,AES,HV,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,SENSOR,ARAT
cpu3: 256KB 64b/line 8-way L2 cache
cpu3: smt 0, core 1, package 1
ioapic0 at mainbus0: apid 4 pa 0xfec00000, version 11, 24 pins
acpimcfg0 at acpi0 addr 0xf0000000, bus 0-127
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpicpu0 at acpi0: C1(@1 halt!)
acpicpu1 at acpi0: C1(@1 halt!)
acpicpu2 at acpi0: C1(@1 halt!)
acpicpu3 at acpi0: C1(@1 halt!)
"PNP0001" at acpi0 not configured
"PNP0303" at acpi0 not configured
"PNP0F13" at acpi0 not configured
"PNP0A05" at acpi0 not configured
"PNP0400" at acpi0 not configured
"PNP0501" at acpi0 not configured
"PNP0501" at acpi0 not configured
"PNP0700" at acpi0 not configured
acpiac0 at acpi0: AC unit online
pvbus0 at mainbus0: VMware
vmt0 at pvbus0
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel 82443BX AGP" rev 0x01
ppb0 at pci0 dev 1 function 0 "Intel 82443BX AGP" rev 0x01
pci1 at ppb0 bus 1
pcib0 at pci0 dev 7 function 0 "Intel 82371AB PIIX4 ISA" rev 0x08
pciide0 at pci0 dev 7 function 1 "Intel 82371AB IDE" rev 0x01: DMA, channel 0
configured to compatibility, channel 1 configured to compatibility
pciide0: channel 0 disabled (no drives)
atapiscsi0 at pciide0 channel 1 drive 0
scsibus1 at atapiscsi0: 2 targets
cd0 at scsibus1 targ 0 lun 0: <NECVMWar, VMware IDE CDR10, 1.00> ATAPI 5/cdrom
removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
piixpm0 at pci0 dev 7 function 3 "Intel 82371AB Power" rev 0x08: SMBus disabled
"VMware VMCI" rev 0x10 at pci0 dev 7 function 7 not configured
vga1 at pci0 dev 15 function 0 "VMware SVGA II" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
mpi0 at pci0 dev 16 function 0 "Symbios Logic 53c1030" rev 0x01: apic 4 int 17
mpi0: 0, firmware 1.3.41.32
scsibus2 at mpi0: 16 targets, initiator 7
sd0 at scsibus2 targ 0 lun 0: <VMware, Virtual disk, 1.0> SCSI2 0/direct fixed
sd0: 20480MB, 512 bytes/sector, 41943040 sectors
mpi0: target 0 Sync at 160MHz width 16bit offset 127 QAS 1 DT 1 IU 1
ppb1 at pci0 dev 17 function 0 "VMware PCI" rev 0x02
pci2 at ppb1 bus 2
ppb2 at pci0 dev 21 function 0 "VMware PCIE" rev 0x01
pci3 at ppb2 bus 3
ppb3 at pci0 dev 21 function 1 "VMware PCIE" rev 0x01
pci4 at ppb3 bus 4
ppb4 at pci0 dev 21 function 2 "VMware PCIE" rev 0x01
pci5 at ppb4 bus 5
ppb5 at pci0 dev 21 function 3 "VMware PCIE" rev 0x01
pci6 at ppb5 bus 6
ppb6 at pci0 dev 21 function 4 "VMware PCIE" rev 0x01
pci7 at ppb6 bus 7
ppb7 at pci0 dev 21 function 5 "VMware PCIE" rev 0x01
pci8 at ppb7 bus 8
ppb8 at pci0 dev 21 function 6 "VMware PCIE" rev 0x01
pci9 at ppb8 bus 9
ppb9 at pci0 dev 21 function 7 "VMware PCIE" rev 0x01
pci10 at ppb9 bus 10
ppb10 at pci0 dev 22 function 0 "VMware PCIE" rev 0x01
pci11 at ppb10 bus 11
vmx0 at pci11 dev 0 function 0 "VMware VMXNET3" rev 0x01: apic 4 int 19,
address 00:50:56:01:01:02
ppb11 at pci0 dev 22 function 1 "VMware PCIE" rev 0x01
pci12 at ppb11 bus 12
vmx1 at pci12 dev 0 function 0 "VMware VMXNET3" rev 0x01: apic 4 int 19,
address 00:50:56:01:01:01
ppb12 at pci0 dev 22 function 2 "VMware PCIE" rev 0x01
pci13 at ppb12 bus 13
vmx2 at pci13 dev 0 function 0 "VMware VMXNET3" rev 0x01: apic 4 int 19,
address 00:0c:29:4c:bb:99
ppb13 at pci0 dev 22 function 3 "VMware PCIE" rev 0x01
pci14 at ppb13 bus 14
ppb14 at pci0 dev 22 function 4 "VMware PCIE" rev 0x01
pci15 at ppb14 bus 15
ppb15 at pci0 dev 22 function 5 "VMware PCIE" rev 0x01
pci16 at ppb15 bus 16
ppb16 at pci0 dev 22 function 6 "VMware PCIE" rev 0x01
pci17 at ppb16 bus 17
ppb17 at pci0 dev 22 function 7 "VMware PCIE" rev 0x01
pci18 at ppb17 bus 18
ppb18 at pci0 dev 23 function 0 "VMware PCIE" rev 0x01
pci19 at ppb18 bus 19
vmx3 at pci19 dev 0 function 0 "VMware VMXNET3" rev 0x01: apic 4 int 16,
address 00:0c:29:4c:bb:a3
ppb19 at pci0 dev 23 function 1 "VMware PCIE" rev 0x01
pci20 at ppb19 bus 20
vmx4 at pci20 dev 0 function 0 "VMware VMXNET3" rev 0x01: apic 4 int 16,
address 00:0c:29:4c:bb:ad
ppb20 at pci0 dev 23 function 2 "VMware PCIE" rev 0x01
pci21 at ppb20 bus 21
vmx5 at pci21 dev 0 function 0 "VMware VMXNET3" rev 0x01: apic 4 int 16,
address 00:0c:29:4c:bb:b7
ppb21 at pci0 dev 23 function 3 "VMware PCIE" rev 0x01
pci22 at ppb21 bus 22
ppb22 at pci0 dev 23 function 4 "VMware PCIE" rev 0x01
pci23 at ppb22 bus 23
ppb23 at pci0 dev 23 function 5 "VMware PCIE" rev 0x01
pci24 at ppb23 bus 24
ppb24 at pci0 dev 23 function 6 "VMware PCIE" rev 0x01
pci25 at ppb24 bus 25
ppb25 at pci0 dev 23 function 7 "VMware PCIE" rev 0x01
pci26 at ppb25 bus 26
ppb26 at pci0 dev 24 function 0 "VMware PCIE" rev 0x01
pci27 at ppb26 bus 27
ppb27 at pci0 dev 24 function 1 "VMware PCIE" rev 0x01
pci28 at ppb27 bus 28
ppb28 at pci0 dev 24 function 2 "VMware PCIE" rev 0x01
pci29 at ppb28 bus 29
ppb29 at pci0 dev 24 function 3 "VMware PCIE" rev 0x01
pci30 at ppb29 bus 30
ppb30 at pci0 dev 24 function 4 "VMware PCIE" rev 0x01
pci31 at ppb30 bus 31
ppb31 at pci0 dev 24 function 5 "VMware PCIE" rev 0x01
pci32 at ppb31 bus 32
ppb32 at pci0 dev 24 function 6 "VMware PCIE" rev 0x01
pci33 at ppb32 bus 33
ppb33 at pci0 dev 24 function 7 "VMware PCIE" rev 0x01
pci34 at ppb33 bus 34
isa0 at pcib0
isadma0 at isa0
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5 irq 1 irq 12
pckbd0 at pckbc0 (kbd slot)
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
vscsi0 at root
scsibus3 at vscsi0: 256 targets
softraid0 at root
scsibus4 at softraid0: 256 targets
root on sd0a (207664f66ac3c7e3.a) swap on sd0b dump on sd0b
carp: pfsync0 demoted group carp by 32 to 160 (pfsync init)
carp: pfsync0 demoted group pfsync by 32 to 32 (pfsync init)
carp: pfsync0 demoted group carp by 1 to 161 (pfsync bulk start)
carp: pfsync0 demoted group pfsync by 1 to 33 (pfsync bulk start)
carp: pfsync0 demoted group carp by -1 to 160 (pfsync bulk done)
carp: pfsync0 demoted group pfsync by -1 to 32 (pfsync bulk done)
carp: pfsync0 demoted group carp by -32 to 128 (pfsync init)
carp: pfsync0 demoted group pfsync by -32 to 0 (pfsync init)
carp1: state transition: BACKUP -> MASTER
carp101: state transition: BACKUP -> MASTER
carp122: state transition: BACKUP -> MASTER
carp2: state transition: BACKUP -> MASTER
arp info overwritten for 192.168.78.12 by 18:65:90:d2:1b:f3 on vmx1
arp info overwritten for 192.168.78.12 by 68:5b:35:c5:15:bd on vmx1
arp info overwritten for 192.168.78.12 by 18:65:90:d2:1b:f3 on vmx1
arp info overwritten for 192.168.78.12 by 68:5b:35:c5:15:bd on vmx1
arp info overwritten for 192.168.78.12 by 18:65:90:d2:1b:f3 on vmx1
arp info overwritten for 192.168.78.12 by 68:5b:35:c5:15:bd on vmx1
arp info overwritten for 192.168.78.12 by 18:65:90:d2:1b:f3 on vmx1
arp info overwritten for 192.168.78.12 by 68:5b:35:c5:15:bd on vmx1
arp info overwritten for 192.168.78.12 by 18:65:90:d2:1b:f3 on vmx1
arp info overwritten for 192.168.78.12 by 68:5b:35:c5:15:bd on vmx1
