Thanks to two off-list replies, I looked at pf. Turns out, pf is
blocking these packets. However, it's blocking them on the wrong
interface.
Recap: dhclient runs on vlan4. The DHCP server is 10.10.0.33. I have
a route to 10.10.0.0/16 out over vlan4. My default route is over
vlan34.
Packets sent by dhclient to 10.10.0.33 are blocked by pf with the
following pflog output:
21:42:51.212547 rule 1/(match) [uid 0, pid 91842] block out on vlan34: [uid
4294967295, pid 100000] 10.10.48.29.68 > 10.10.0.33.67: [udp sum ok]
xid:0xa33fd786 C:10.10.48.29 ether 00:60:e0:52:0f:9c vend-rfc1048 DHCP:REQUEST
HN:"tuna" PR:SM+BR+DG CID:1.0.96.224.82.15.156 [tos 0x10] (ttl 128, id 53107,
len 328, bad ip cksum f543! -> 25d0)
21:42:52.222508 rule 1/(match) [uid 0, pid 91842] block out on vlan34: [uid
4294967295, pid 100000] 10.10.48.29.68 > 10.10.0.33.67: [udp sum ok]
xid:0xa33fd786 secs:1 C:10.10.48.29 ether 00:60:e0:52:0f:9c vend-rfc1048
DHCP:REQUEST HN:"tuna" PR:SM+BR+DG CID:1.0.96.224.82.15.156 [tos 0x10] (ttl
128, id 2876, len 328, bad ip cksum f543! -> ea07)
pf rule 1 says:
@1 block return out log on vlan34 all
[ Evaluations: 470943 Packets: 578 Bytes: 52070 States: 0 ]
[ Inserted: uid 0 pid 91842 State Creations: 0 ]
(later on in my pf.conf I have explicit rules that allow traffic to
10.10.0.0/16 over vlan4, but that's obviously not matched)
Why would a packet for 10.10.0.33 be sent out over vlan34 (and be
blocked there) if there's a specific route over vlan4?
My full routing table is (MACs of the innocent have been masked out):
--- netstat -rnf inet ------------------------------------------------
Routing tables
Internet:
Destination Gateway Flags Refs Use Mtu Prio Iface
default 84.245.42.1 UGS 946 1243526112 - 8 vlan34
10.10/16 10.10.48.1 UGS 0 2423 - 8 vlan4
10.10.48/21 10.10.48.29 UCn 1 0 - 4 vlan4
10.10.48.1 link#14 UHLch 2 39 - 3 vlan4
10.10.48.29 00:60:e0:52:0f:9c UHLl 0 42309 - 1 vlan4
10.10.55.255 10.10.48.29 UHb 0 0 - 1 vlan4
84.245.42/24 84.245.42.135 UCn 1 0 - 4 vlan34
84.245.42.1 00:30:88:16:ac:fe UHLch 1 2240 - 3 vlan34
84.245.42.135 00:60:e0:52:0f:98 UHLl 0 468649319 - 1 vlan34
84.245.42.255 84.245.42.135 UHb 0 0 - 1 vlan34
127/8 127.0.0.1 UGRS 0 0 32768 8 lo0
127.0.0.1 127.0.0.1 UHhl 3 13843 32768 1 lo0
185.6.48.0/26 10.10.48.1 UGS 0 6209 - 8 vlan4
192.168.34/24 192.168.34.1 UCn 12 7318722 - 4 em0
192.168.34.1 00:60:e0:52:0f:96 UHLl 0 6004466 - 1 em0
192.168.34.2 00:60:e0:52:0f:96 UHLl 0 110 - 1 em0
192.168.34.2/32 192.168.34.2 UCn 0 0 - 4 em0
192.168.34.20 __:__:__:__:__:__ UHLc 1 5383583 - 3 em0
192.168.34.21 __:__:__:__:__:__ UHLc 0 7142445 - 3 em0
192.168.34.22 __:__:__:__:__:__ UHLc 0 3109025 - 3 em0
192.168.34.23 __:__:__:__:__:__ UHLc 0 3109116 - 3 em0
192.168.34.131 __:__:__:__:__:__ UHLc 0 7633977 - 3 em0
192.168.34.132 __:__:__:__:__:__ UHLc 0 3256650 - 3 em0
192.168.34.136 __:__:__:__:__:__ UHLc 0 284257197 - 3 em0
192.168.34.147 __:__:__:__:__:__ UHLc 0 7289189 - 3 em0
192.168.34.149 __:__:__:__:__:__ UHLc 14 85532587 - 3 em0
192.168.34.151 __:__:__:__:__:__ UHLc 1 7306019 - 3 em0
192.168.34.197 __:__:__:__:__:__ UHLc 0 1849421 - 3 em0
192.168.34.251 __:__:__:__:__:__ UHLc 0 7274945 - 3 em0
192.168.34.255 192.168.34.1 UHb 0 0 - 1 em0
192.168.35/24 192.168.35.1 UCn 0 0 - 4 vlan10
192.168.35.1 00:60:e0:52:0f:97 UHLl 0 592 - 1 vlan10
192.168.35.255 192.168.35.1 UHb 0 0 - 1 vlan10
192.168.36/24 192.168.36.1 UCn 1 22 - 4 vlan20
192.168.36.1 00:60:e0:52:0f:96 UHLl 0 82722 - 1 vlan20
192.168.36.100 __:__:__:__:__:__ UHLc 1 26934 - 3 vlan20
192.168.36.255 192.168.36.1 UHb 0 22 - 1 vlan20
203.0.113.64/27 203.0.113.66 UGS 0 0 - 8 tun0
203.0.113.65 203.0.113.65 UHl 0 0 - 1 tun0
203.0.113.66 203.0.113.65 UHh 1 1 - 8 tun0
239.0.2.1 10.10.48.29 UHm 0 313008 - 8 vlan4
239.0.2.2 10.10.48.29 UHm 0 314561 - 8 vlan4
----------------------------------------------------------------------
There's no capture of the blocked packets (of course), but the
successful packets (broadcasted) look like:
21:42:53.232446 00:60:e0:52:0f:9c ff:ff:ff:ff:ff:ff 0800 342: 10.10.48.29.68 >
255.255.255.255.67: [udp sum ok] xid:0xa33fd786 secs:2 C:10.10.48.29
vend-rfc1048 DHCP:REQUEST HN:"tuna" PR:SM+BR+DG CID:1.0.96.224.82.15.156 [tos
0x10] (ttl 128, id 0, len 328)
21:42:53.448939 02:03:3b:04:90:94 00:60:e0:52:0f:9c 0800 342: 10.10.0.33.67 >
10.10.48.29.68: [udp sum ok] hops:1 xid:0xa33fd786 secs:2 C:10.10.48.29
Y:10.10.48.29 vend-rfc1048 DHCP:ACK SID:10.10.0.33 LT:3600 SM:255.255.248.0
DG:10.10.48.1 [tos 0x60] (ttl 16, id 0, len 328)
--- ifconfig -a ------------------------------------------------------
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 32768
description: loopback
index 8 priority 0 llprio 3
groups: lo
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x8
inet 127.0.0.1 netmask 0xff000000
em0: flags=8b43<UP,BROADCAST,RUNNING,PROMISC,ALLMULTI,SIMPLEX,MULTICAST> mtu
1500
lladdr 00:60:e0:52:0f:96
description: to wireless
index 1 priority 0 llprio 3
groups: lan
media: Ethernet autoselect (1000baseT
full-duplex,master,rxpause,txpause)
status: active
inet 192.168.34.1 netmask 0xffffff00 broadcast 192.168.34.255
inet6 fe80::260:e0ff:fe52:f96%em0 prefixlen 64 scopeid 0x1
inet6 2a02:898:28:200::1 prefixlen 64
inet6 2a02:898:28:200::2 prefixlen 128
inet6 2a02:898:28:200::80 prefixlen 128
em1: flags=8b43<UP,BROADCAST,RUNNING,PROMISC,ALLMULTI,SIMPLEX,MULTICAST> mtu
1500
lladdr 00:60:e0:52:0f:97
description: to media
index 2 priority 0 llprio 3
groups: lan
media: Ethernet autoselect (1000baseT full-duplex,rxpause,txpause)
status: active
em2: flags=8b43<UP,BROADCAST,RUNNING,PROMISC,ALLMULTI,SIMPLEX,MULTICAST> mtu
1500
lladdr 00:60:e0:52:0f:98
description: to uplink
index 3 priority 0 llprio 3
media: Ethernet autoselect (1000baseT
full-duplex,master,rxpause,txpause)
status: active
em3: flags=8b43<UP,BROADCAST,RUNNING,PROMISC,ALLMULTI,SIMPLEX,MULTICAST> mtu
1500
lladdr 00:60:e0:52:0f:99
description: to upstairs
index 4 priority 0 llprio 3
groups: lan
media: Ethernet autoselect (1000baseT full-duplex,rxpause,txpause)
status: active
em4: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:60:e0:52:0f:9a
index 5 priority 0 llprio 3
media: Ethernet autoselect (none)
status: no carrier
em5: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:60:e0:52:0f:9b
index 6 priority 0 llprio 3
media: Ethernet autoselect (none)
status: no carrier
enc0: flags=0<>
index 7 priority 0 llprio 3
groups: enc
status: active
lo1: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 32768
index 9 priority 0 llprio 3
groups: lo
inet6 ::1 prefixlen 128
inet6 fe80::1%lo1 prefixlen 64 scopeid 0x9
inet6 ::2 prefixlen 128
vlan10: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:60:e0:52:0f:97
description: to set-top-box
index 10 priority 0 llprio 3
vlan: 10 parent interface: em1
vnetid: 10
parent: em1
groups: vlan
status: active
inet 192.168.35.1 netmask 0xffffff00 broadcast 192.168.35.255
vlan34: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:60:e0:52:0f:98
description: Tweak internet
index 13 priority 0 llprio 3
vlan: 34 parent interface: em2
vnetid: 34
parent: em2
groups: vlan egress
status: active
inet 84.245.42.135 netmask 0xffffff00 broadcast 84.245.42.255
vlan4: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:60:e0:52:0f:9c
description: TV upstream
index 14 priority 0 llprio 3
vlan: 4 parent interface: em2
vnetid: 4
parent: em2
groups: vlan
status: active
inet 10.10.48.29 netmask 0xfffff800 broadcast 10.10.55.255
tun0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1500
index 15 priority 0 llprio 3
groups: tun
status: active
inet 203.0.113.65 --> 203.0.113.66 netmask 0xffffffff
gif0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1420
index 16 priority 0 llprio 3
groups: gif egress
tunnel: inet 84.245.42.135 -> 94.142.244.6
inet6 fe80::260:e0ff:fe52:f96%gif0 -> prefixlen 64 scopeid 0x10
inet6 2a02:898:28:100::2 -> 2a02:898:28:100::1 prefixlen 128
bridge0: flags=41<UP,RUNNING>
description: LAN bridge
index 17 llprio 3
groups: bridge
priority 32768 hellotime 2 fwddelay 15 maxage 20 holdcnt 6 proto rstp
em0 flags=3<LEARNING,DISCOVER>
port 1 ifpriority 0 ifcost 0
em1 flags=3<LEARNING,DISCOVER>
port 2 ifpriority 0 ifcost 0
em3 flags=3<LEARNING,DISCOVER>
port 4 ifpriority 0 ifcost 0
pflog0: flags=141<UP,RUNNING,PROMISC> mtu 33136
description: pf log
index 20 priority 0 llprio 3
groups: pflog
vlan20: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:60:e0:52:0f:96
description: WiFi guest network downstairs
index 22 priority 0 llprio 3
vlan: 20 parent interface: em0
vnetid: 20
parent: em0
groups: vlan
status: active
inet 192.168.36.1 netmask 0xffffff00 broadcast 192.168.36.255
inet6 fe80::260:e0ff:fe52:f96%vlan20 prefixlen 64 scopeid 0x16
inet6 2a02:898:28:201::1 prefixlen 64
vlan21: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:60:e0:52:0f:99
description: WiFi guest network upstairs
index 23 priority 0 llprio 3
vlan: 20 parent interface: em3
vnetid: 20
parent: em3
groups: vlan
status: active
bridge20: flags=41<UP,RUNNING>
description: Guest wifi bridge
index 24 llprio 3
groups: bridge
priority 32768 hellotime 2 fwddelay 15 maxage 20 holdcnt 6 proto rstp
vlan20 flags=3<LEARNING,DISCOVER>
port 22 ifpriority 0 ifcost 0
vlan21 flags=3<LEARNING,DISCOVER>
port 23 ifpriority 0 ifcost 0
----------------------------------------------------------------------
Thanks,
Paul 'WEiRD' de Weerd
On Tue, Jun 20, 2017 at 08:23:31PM +0200, Paul de Weerd wrote:
| >Synopsis: dhclient can't DHCPREQUEST using static route
| >Category: system
| >Environment:
| System : OpenBSD 6.1
| Details : OpenBSD 6.1-current (GENERIC.MP) #76: Sun May 21 22:37:18
MDT 2017
|
[email protected]:/usr/src/sys/arch/amd64/compile/GENERIC.MP
|
| Architecture: OpenBSD.amd64
| Machine : amd64
| >Description:
|
| When refreshing the DHCP lease from my ISP, dhclient first
| DHCPREQUESTs the old IP address from the known DHCP server. This
| errors out due to 'No route to host' (the DHCP server is not in the
| same IP subnet as the lease), while a route is definitely present. It
| subsequently doas a broadcast request and then gets a lease (from the
| same DHCP server):
|
| 2017-06-20T18:09:57.349Z tuna dhclient[30480]: DHCPREQUEST on vlan4 to
10.10.0.33
| 2017-06-20T18:09:57.349Z tuna dhclient[30480]: send_packet: No route to host
| 2017-06-20T18:09:58.359Z tuna dhclient[30480]: DHCPREQUEST on vlan4 to
10.10.0.33
| 2017-06-20T18:09:58.359Z tuna dhclient[30480]: send_packet: No route to host
| 2017-06-20T18:09:59.369Z tuna dhclient[30480]: DHCPREQUEST on vlan4 to
255.255.255.255
| 2017-06-20T18:09:59.586Z tuna dhclient[30480]: DHCPACK from 10.10.0.33
(02:03:3b:04:90:94)
| 2017-06-20T18:09:59.586Z tuna dhclient[30480]: bound to 10.10.48.29 --
renewal in 1800 seconds.
|
| [weerd@tuna] $ cat /var/db/dhclient.leases.vlan4
| lease {
| interface "vlan4";
| fixed-address 10.10.48.29;
| next-server 0.0.0.0;
| option subnet-mask 255.255.248.0;
| option routers 10.10.48.1;
| option dhcp-lease-time 3600;
| option dhcp-message-type 5;
| option dhcp-server-identifier 10.10.0.33;
| renew 2 2017/06/20 18:39:59 UTC;
| rebind 2 2017/06/20 19:02:29 UTC;
| expire 2 2017/06/20 19:09:59 UTC;
| }
|
| [weerd@tuna] $ route get 10.10.0.33
| route to: 10.10.0.33
| destination: 10.10.0.0
| mask: 255.255.0.0
| gateway: 10.10.48.1
| interface: vlan4
| if address: 10.10.48.29
| priority: 8 (static)
| flags: <UP,GATEWAY,DONE,STATIC>
| use mtu expire
| 2321 0 0
|
| [weerd@tuna] $ cat /etc/hostname.vlan4
| vlan 4 vlandev em2
| lladdr 00:60:e0:52:0f:9c
| description "TV upstream"
| dhcp
| !/sbin/route add 185.6.48.0/26 10.10.48.1
| !/sbin/route add 10.10.0.0/16 10.10.48.1
|
| >How-To-Repeat:
| Start dhclient on an interface that gets a lease from a
| non-local DHCP server (I think).
|
| >Fix:
| <how to correct or work around the problem, if known (multiple lines)>
|
| dmesg:
| OpenBSD 6.1-current (GENERIC.MP) #76: Sun May 21 22:37:18 MDT 2017
| [email protected]:/usr/src/sys/arch/amd64/compile/GENERIC.MP
| real mem = 2120876032 (2022MB)
| avail mem = 2050867200 (1955MB)
| mpath0 at root
| scsibus0 at mpath0: 256 targets
| mainbus0 at root
| bios0 at mainbus0: SMBIOS rev. 2.6 @ 0xfc690 (23 entries)
| bios0: vendor American Megatrends Inc. version "080015" date 09/15/2010
| bios0: AXIOMTEK NA-320
| acpi0 at bios0: rev 2
| acpi0: sleep states S0 S1 S4 S5
| acpi0: tables DSDT FACP APIC MCFG OEMB GSCI SSDT
| acpi0: wakeup devices P0P1(S4) USB0(S4) USB1(S4) USB2(S4) USB3(S4) EUSB(S4)
P0P4(S4) P0P5(S4) P0P6(S4) P0P7(S4) P0P8(S4) P0P9(S4) USB4(S4) USB5(S4)
USBE(S4) GBEC(S4)
| acpitimer0 at acpi0: 3579545 Hz, 24 bits
| acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
| cpu0 at mainbus0: apid 0 (boot processor)
| cpu0: Intel(R) Atom(TM) CPU D510 @ 1.66GHz, 1662.71 MHz
| cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,TM2,SSSE3,CX16,xTPR,PDCM,MOVBE,NXE,LONG,LAHF,PERF,SENSOR
| cpu0: 512KB 64b/line 8-way L2 cache
| cpu0: smt 0, core 0, package 0
| mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
| cpu0: apic clock running at 166MHz
| cpu0: mwait min=64, max=64, C-substates=0.1, IBE
| cpu1 at mainbus0: apid 2 (application processor)
| cpu1: Intel(R) Atom(TM) CPU D510 @ 1.66GHz, 1662.50 MHz
| cpu1:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,TM2,SSSE3,CX16,xTPR,PDCM,MOVBE,NXE,LONG,LAHF,PERF,SENSOR
| cpu1: 512KB 64b/line 8-way L2 cache
| cpu1: smt 0, core 1, package 0
| cpu2 at mainbus0: apid 1 (application processor)
| cpu2: Intel(R) Atom(TM) CPU D510 @ 1.66GHz, 1662.50 MHz
| cpu2:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,TM2,SSSE3,CX16,xTPR,PDCM,MOVBE,NXE,LONG,LAHF,PERF,SENSOR
| cpu2: 512KB 64b/line 8-way L2 cache
| cpu2: smt 1, core 0, package 0
| cpu3 at mainbus0: apid 3 (application processor)
| cpu3: Intel(R) Atom(TM) CPU D510 @ 1.66GHz, 1662.50 MHz
| cpu3:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,TM2,SSSE3,CX16,xTPR,PDCM,MOVBE,NXE,LONG,LAHF,PERF,SENSOR
| cpu3: 512KB 64b/line 8-way L2 cache
| cpu3: smt 1, core 1, package 0
| ioapic0 at mainbus0: apid 4 pa 0xfec00000, version 20, 24 pins
| acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255
| acpiprt0 at acpi0: bus 0 (PCI0)
| acpiprt1 at acpi0: bus 2 (P0P4)
| acpiprt2 at acpi0: bus 3 (P0P5)
| acpiprt3 at acpi0: bus 4 (P0P6)
| acpiprt4 at acpi0: bus 5 (P0P7)
| acpiprt5 at acpi0: bus 6 (P0P8)
| acpiprt6 at acpi0: bus 7 (P0P9)
| acpicpu0 at acpi0: C1(1000@1 mwait.1)
| acpicpu1 at acpi0: C1(1000@1 mwait.1)
| acpicpu2 at acpi0: C1(@1 halt!)
| acpicpu3 at acpi0: C1(@1 halt!)
| "PNP0501" at acpi0 not configured
| "PNP0501" at acpi0 not configured
| acpibtn0 at acpi0: PWRB
| pci0 at mainbus0 bus 0
| pchb0 at pci0 dev 0 function 0 "Intel Pineview DMI" rev 0x02
| inteldrm0 at pci0 dev 2 function 0 "Intel Pineview Video" rev 0x02
| drm0 at inteldrm0
| intagp0 at inteldrm0
| agp0 at intagp0: aperture at 0xd0000000, size 0x10000000
| inteldrm0: msi
| Raw EDID:
|
| 00 00 00 00 00 00 00 00 01 01 01 01 01 01 01 01
| 03 03 03 03 03 03 03 03 07 07 07 07 07 07 07 07
| 0f 0f 0f 0f 0f 0f 0f 0f 1f 1f 1f 1f 1f 1f 1f 1f
| 3f 3f 3f 3f 3f 3f 3f 3f 7f 7f 7f 7f 7f 7f 7f 7f
| ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
| ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
| ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
| ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
| Raw EDID:
|
| fc fc fc fc fc fc fc fc f9 f9 f9 f9 f9 f9 f9 f9
| f3 f3 f3 f3 f3 f3 f3 f3 e7 e7 e7 e7 e7 e7 e7 e7
| cf cf cf cf cf cf cf cf 9f 9f 9f 9f 9f 9f 9f 9f
| 3f 3f 3f 3f 3f 3f 3f 3f 7f 7f 7f 7f 7f 7f 7f 7f
| ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
| ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
| ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
| ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
| Raw EDID:
|
| fc fc fc fc fc fc fc fc f9 f9 f9 f9 f9 f9 f9 f9
| f3 f3 f3 f3 f3 f3 f3 f3 e7 e7 e7 e7 e7 e7 e7 e7
| cf cf cf cf cf cf cf cf 9f 9f 9f 9f 9f 9f 9f 9f
| 3f 3f 3f 3f 3f 3f 3f 3f 7f 7f 7f 7f 7f 7f 7f 7f
| ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
| ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
| ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
| ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
| Raw EDID:
|
| fc fc fc fc fc fc fc fc f9 f9 f9 f9 f9 f9 f9 f9
| f3 f3 f3 f3 f3 f3 f3 f3 e7 e7 e7 e7 e7 e7 e7 e7
| cf cf cf cf cf cf cf cf 9f 9f 9f 9f 9f 9f 9f 9f
| 3f 3f 3f 3f 3f 3f 3f 3f 7f 7f 7f 7f 7f 7f 7f 7f
| ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
| ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
| ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
| ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
| drm:pid0:drm_do_get_edid *WARNING* VGA-1: EDID block 0 invalid.
| inteldrm0: 1024x768, 32bpp
| wsdisplay0 at inteldrm0 mux 1: console (std, vt100 emulation)
| wsdisplay0: screen 1-5 added (std, vt100 emulation)
| ppb0 at pci0 dev 28 function 0 "Intel 82801H PCIE" rev 0x04: msi
| pci1 at ppb0 bus 2
| em0 at pci1 dev 0 function 0 "Intel 82583V" rev 0x00: msi, address
00:60:e0:52:0f:96
| ppb1 at pci0 dev 28 function 1 "Intel 82801H PCIE" rev 0x04: msi
| pci2 at ppb1 bus 3
| em1 at pci2 dev 0 function 0 "Intel 82583V" rev 0x00: msi, address
00:60:e0:52:0f:97
| ppb2 at pci0 dev 28 function 2 "Intel 82801H PCIE" rev 0x04: msi
| pci3 at ppb2 bus 4
| em2 at pci3 dev 0 function 0 "Intel 82583V" rev 0x00: msi, address
00:60:e0:52:0f:98
| ppb3 at pci0 dev 28 function 3 "Intel 82801H PCIE" rev 0x04: msi
| pci4 at ppb3 bus 5
| em3 at pci4 dev 0 function 0 "Intel 82583V" rev 0x00: msi, address
00:60:e0:52:0f:99
| ppb4 at pci0 dev 28 function 4 "Intel 82801H PCIE" rev 0x04: msi
| pci5 at ppb4 bus 6
| em4 at pci5 dev 0 function 0 "Intel 82583V" rev 0x00: msi, address
00:60:e0:52:0f:9a
| ppb5 at pci0 dev 28 function 5 "Intel 82801H PCIE" rev 0x04: msi
| pci6 at ppb5 bus 7
| em5 at pci6 dev 0 function 0 "Intel 82583V" rev 0x00: msi, address
00:60:e0:52:0f:9b
| uhci0 at pci0 dev 29 function 0 "Intel 82801H USB" rev 0x04: apic 4 int 23
| uhci1 at pci0 dev 29 function 1 "Intel 82801H USB" rev 0x04: apic 4 int 19
| uhci2 at pci0 dev 29 function 2 "Intel 82801H USB" rev 0x04: apic 4 int 18
| ehci0 at pci0 dev 29 function 7 "Intel 82801H USB" rev 0x04: apic 4 int 23
| usb0 at ehci0: USB revision 2.0
| uhub0 at usb0 configuration 1 interface 0 "Intel EHCI root hub" rev 2.00/1.00
addr 1
| ppb6 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xf4
| pci7 at ppb6 bus 1
| pcib0 at pci0 dev 31 function 0 "Intel 82801HBM LPC" rev 0x04
| pciide0 at pci0 dev 31 function 1 "Intel 82801HBM IDE" rev 0x04: DMA, channel
0 configured to compatibility, channel 1 configured to compatibility
| pciide0: channel 0 disabled (no drives)
| pciide0: channel 1 ignored (disabled)
| ahci0 at pci0 dev 31 function 2 "Intel 82801HBM AHCI" rev 0x04: msi, AHCI 1.1
| ahci0: port 0: 3.0Gb/s
| scsibus1 at ahci0: 32 targets
| sd0 at scsibus1 targ 0 lun 0: <ATA, M4-CT256M4SSD2, 070H> SCSI3 0/direct
fixed naa.500a07510927b253
| sd0: 244198MB, 512 bytes/sector, 500118192 sectors, thin
| ichiic0 at pci0 dev 31 function 3 "Intel 82801H SMBus" rev 0x04: apic 4 int 17
| iic0 at ichiic0
| spdmem0 at iic0 addr 0x50: 2GB DDR2 SDRAM non-parity PC2-6400CL6 SO-DIMM
| usb1 at uhci0: USB revision 1.0
| uhub1 at usb1 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00
addr 1
| usb2 at uhci1: USB revision 1.0
| uhub2 at usb2 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00
addr 1
| usb3 at uhci2: USB revision 1.0
| uhub3 at usb3 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00
addr 1
| isa0 at pcib0
| isadma0 at isa0
| com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
| com0: console
| com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
| pckbc0 at isa0 port 0x60/5 irq 1 irq 12
| pckbd0 at pckbc0 (kbd slot)
| wskbd0 at pckbd0: console keyboard, using wsdisplay0
| pcppi0 at isa0 port 0x61
| spkr0 at pcppi0
| wbsio0 at isa0 port 0x2e/2: W83627DHG-P rev 0x73
| lm1 at wbsio0 port 0xa00/8: W83627DHG
| umass0 at uhub0 port 1 configuration 1 interface 0 "Western Digital My
Passport 259D" rev 2.10/10.12 addr 2
| umass0: using SCSI over Bulk-Only
| scsibus2 at umass0: 2 targets, initiator 0
| sd1 at scsibus2 targ 1 lun 0: <WD, My Passport 259D, 1012> SCSI4 0/direct
fixed
| sd1: 3815415MB, 512 bytes/sector, 7813969920 sectors
| ses0 at scsibus2 targ 1 lun 1: <WD, SES Device, 1012> SCSI4 13/enclosure
services fixed
| ses0: unable to read enclosure configuration
| uhub4 at uhub0 port 2 configuration 1 interface 0 "Genesys Logic USB2.0 Hub"
rev 2.00/85.32 addr 3
| uhidev0 at uhub4 port 1 configuration 1 interface 0 "RDing TEMPERHUM1V1.2"
rev 2.00/0.01 addr 4
| uhidev0: iclass 3/1, 1 report id
| ukbd0 at uhidev0 reportid 1: 8 variable keys, 5 key codes
| wskbd1 at ukbd0 mux 1
| wskbd1: connecting to wsdisplay0
| uhidev1 at uhub4 port 1 configuration 1 interface 1 "RDing TEMPERHUM1V1.2"
rev 2.00/0.01 addr 4
| uhidev1: iclass 3/1
| ugold0 at uhidev1
| uftdi0 at uhub4 port 2 configuration 1 interface 0 "FTDI SYNLEAF - FT232R USB
UART" rev 2.00/6.00 addr 5
| ucom0 at uftdi0 portno 1
| vscsi0 at root
| scsibus3 at vscsi0: 256 targets
| softraid0 at root
| scsibus4 at softraid0: 256 targets
| root on sd0a (86b81881bbaa38a1.a) swap on sd0b dump on sd0b
| ugold0: 2 sensors type si7006 (temperature and humidity)
|
| usbdevs:
| Controller /dev/usb0:
| addr 1: high speed, self powered, config 1, EHCI root hub(0x0000),
Intel(0x8086), rev 1.00
| port 1 addr 2: high speed, power 500 mA, config 1, My Passport 259D(0x259d),
Western Digital(0x1058), rev 10.12, iSerialNumber 57583231443736503041334E
| port 2 addr 3: high speed, self powered, config 1, USB2.0 Hub(0x0608),
Genesys Logic(0x05e3), rev 85.32
| port 1 addr 4: low speed, power 100 mA, config 1, TEMPERHUM1V1.2(0x7402),
RDing(0x0c45), rev 0.01
| port 2 addr 5: full speed, power 90 mA, config 1, SYNLEAF - FT232R USB
UART(0x6001), FTDI(0x0403), rev 6.00, iSerialNumber A7XOCBSM
| port 3 powered
| port 4 powered
| port 3 powered
| port 4 powered
| port 5 powered
| port 6 powered
| Controller /dev/usb1:
| addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x8086), rev 1.00
| port 1 powered
| port 2 powered
| Controller /dev/usb2:
| addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x8086), rev 1.00
| port 1 powered
| port 2 powered
| Controller /dev/usb3:
| addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x8086), rev 1.00
| port 1 powered
| port 2 powered
|
|
| --
| >++++++++[<++++++++++>-]<+++++++.>+++[<------>-]<.>+++[<+
| +++++++++++>-]<.>++[<------------>-]<+.--------------.[-]
| http://www.weirdnet.nl/
|
--
>++++++++[<++++++++++>-]<+++++++.>+++[<------>-]<.>+++[<+
+++++++++++>-]<.>++[<------------>-]<+.--------------.[-]
http://www.weirdnet.nl/
