Hi,
a64pine# eeprom -p
Node 0x48
name: ''
serial-number: '92c000ba40e5f79b'
interrupt-parent: 00000001
#address-cells: 00000001
#size-cells: 00000001
model: 'Pine64+'
compatible: 'pine64,pine64-plus' + 'allwinner,sun50i-a64'
Node 0xe8
name: 'memory'
reg: 40000000.40000000
device_type: 'memory'
...OMITTED...
Node 0x2fbc
name: 'chosen'
openbsd,uefi-mmap-desc-ver: 00000001
openbsd,uefi-mmap-desc-size: 00000028
openbsd,uefi-mmap-size: 00004218
openbsd,uefi-mmap-start: 00000000.78d00f90
openbsd,uefi-system-table: 00000000.7dfbab00
openbsd,bootduid: d5ad53bf.b04a5b5e
bootargs: 'sd0a:/bsd'
linux,stdout-path: '/soc@01c00000/serial@01c28000:115200'
stdout-path: 'serial0:115200n8'
a64pine# dmesg | head -4
OpenBSD 6.2-current (GENERIC) #123: Thu Dec 21 14:27:12 MST 2017
[email protected]:/usr/src/sys/arch/arm64/compile/GENERIC
real mem = 879714304 (838MB)
avail mem = 826183680 (787MB)
where and why did it loose that much? given "reg: 40000000.40000000",
and there's no framebuffer mapped or anything? full dmesg below.
-Artturi
OpenBSD 6.2-current (GENERIC) #123: Thu Dec 21 14:27:12 MST 2017
[email protected]:/usr/src/sys/arch/arm64/compile/GENERIC
real mem = 879714304 (838MB)
avail mem = 826183680 (787MB)
mainbus0 at root: Pine64+
cpu0 at mainbus0: ARM Cortex-A53 r0p4
psci0 at mainbus0
agtimer0 at mainbus0: tick rate 24000 KHz
simplebus0 at mainbus0: "soc"
syscon0 at simplebus0: "syscon"
sxiccmu0 at simplebus0
sxipio0 at simplebus0: 103 pins
sxirsb0 at simplebus0
"x-powers,axp803" at sxirsb0 addr 0x3a3 not configured
sximmc0 at simplebus0
sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
ehci0 at simplebus0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00
addr 1
ehci1 at simplebus0
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00
addr 1
com0 at simplebus0: ns16550, no working fifo
com0: console
sxitwi0 at simplebus0
iic0 at sxitwi0
dwxe0 at simplebus0: address 02:ba:40:e5:f7:9b
rgephy0 at dwxe0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5
ampintc0 at simplebus0 nirq 224, ncpu 4: "interrupt-controller"
sxirtc0 at simplebus0
gpio0 at sxipio0: 32 pins
gpio1 at sxipio0: 32 pins
gpio2 at sxipio0: 32 pins
gpio3 at sxipio0: 32 pins
gpio4 at sxipio0: 32 pins
gpio5 at sxipio0: 32 pins
gpio6 at sxipio0: 32 pins
gpio7 at sxipio0: 32 pins
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SU01G, 0080> SCSI2 0/direct removable
sd0: 968MB, 512 bytes/sector, 1984000 sectors
umass0 at uhub1 port 1 configuration 1 interface 0 "vendor 0x18a5 product
0x0302" rev 2.00/1.07 addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <Verbatim, , 8.07> SCSI2 0/direct removable
serial.18a50302112158020639
sd1: 7450MB, 512 bytes/sector, 15257600 sectors
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
bootfile: sd0a:/bsd
boot device: sd0
root on sd1a (d5ad53bfb04a5b5e.a) swap on sd1b dump on sd1b
