Hi,
a64pine# sysctl ddb
ddb.radix=16
ddb.max_width=80
ddb.max_line=24
ddb.tab_stop_width=8
ddb.panic=1
ddb.console=1
ddb.log=1
ddb.trigger=0
a64pine# sysctl ddb.trigger=1
Stopped at ddb_sysctl+0x118:
ddb{0}> c
<FROZEN HERE>
but above does happen only on .MP, twice from the +15tries i've seen it
continue, and it is working reliably on bsd.sp.
It doesn't matter whether "machine cpuinfo" shows that some cpus are
still stopping or stopped, before c[ontinue].
This is irrelevant to me enough, that i didn't dig any deeper.
-Artturi
[ using 1012040 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2018 OpenBSD. All rights reserved. https://www.OpenBSD.org
OpenBSD 6.3-current (GENERIC.MP) #101: Sat May 5 04:12:12 MDT 2018
[email protected]:/usr/src/sys/arch/arm64/compile/GENERIC.MP
real mem = 879362048 (838MB)
avail mem = 822554624 (784MB)
mainbus0 at root: Pine64+
cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4
efi0 at mainbus0: UEFI 2.0.5
efi0: Das U-boot rev 0x0
psci0 at mainbus0: PSCI 0.2
agtimer0 at mainbus0: tick rate 24000 KHz
simplebus0 at mainbus0: "soc"
syscon0 at simplebus0: "syscon"
sxiccmu0 at simplebus0
sxipio0 at simplebus0: 103 pins
ampintc0 at simplebus0 nirq 224, ncpu 4 ipi: 0, 1: "interrupt-controller"
sxiccmu1 at simplebus0
sxipio1 at simplebus0: 13 pins
sxirsb0 at simplebus0
axppmic0 at sxirsb0 addr 0x3a3: AXP803
sximmc0 at simplebus0
sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
ehci0 at simplebus0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00
addr 1
ehci1 at simplebus0
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00
addr 1
com0 at simplebus0: ns16550, no working fifo
com0: console
sxitwi0 at simplebus0
iic0 at sxitwi0
dwxe0 at simplebus0: address 02:ba:40:e5:f7:9b
rgephy0 at dwxe0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5
sxirtc0 at simplebus0
gpio0 at sxipio0: 32 pins
gpio1 at sxipio0: 32 pins
gpio2 at sxipio0: 32 pins
gpio3 at sxipio0: 32 pins
gpio4 at sxipio0: 32 pins
gpio5 at sxipio0: 32 pins
gpio6 at sxipio0: 32 pins
gpio7 at sxipio0: 32 pins
gpio8 at sxipio1: 32 pins
cpu1 at mainbus0 mpidr 1: ARM Cortex-A53 r0p4
cpu2 at mainbus0 mpidr 2: ARM Cortex-A53 r0p4
cpu3 at mainbus0 mpidr 3: ARM Cortex-A53 r0p4
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SU01G, 0080> SCSI2 0/direct removable
sd0: 968MB, 512 bytes/sector, 1984000 sectors
umass0 at uhub1 port 1 configuration 1 interface 0 "Kingston DataTraveler 2.0"
rev 2.00/1.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <Kingston, DataTraveler 2.0, PMAP> SCSI2 0/direct
removable serial.09306545EF90EA262D48
sd1: 14891MB, 512 bytes/sector, 30497664 sectors
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
bootfile: sd0a:/bsd
boot device: sd0
root on sd1a (7280d48fc18aa92a.a) swap on sd1b dump on sd1b
WARNING: / was not properly unmounted
