Hi,
today I wanted to use NetBSD 8.0 on vmm and it fails on boot always at
the same point (see dmesg below). I'm dropped from vmctl back to the
console and the following messages are shown on the OpenBSD host:
2018-09-22T10:11:04.327Z sigma /bsd: vmx_fault_page: uvm_fault returns 14,
GPA=0xfed40014, rip=0xffffffff8021f758
2018-09-22T10:11:04.327Z sigma vmd[39939]: vcpu_run_loop: vm 10 / vcpu 0 run
ioctl failed: Bad address
Originally, I used a disk image (qcow2) from an existing NetBSD qemu
installation
and added the image to vm.conf. I also tried to boot form a fresh 8.0
and 7.2 amd64 ISO image and this also fails with the same message.
Not sure if NetBSD on vmm is even supported... :)
Cheers
Matthias
The dmesg of the booting NetBSD looks as follows:
NetBSD 8.0 (GENERIC) #0: Tue Jul 17 14:59:51 UTC 2018
[email protected]:/usr/src/sys/arch/amd64/compile/GENERIC
total memory = 511 MB
avail memory = 473 MB
cpu_rng: RDSEED
running cgd selftest aes-xts-256 aes-xts-512 done
mainbus0 (root)
ACPI BIOS Error (bug): A valid RSDP was not found (20170303/tbxfroot-261)
acpi_probe: failed to initialize tables
ACPI Error: Could not remove SCI handler (20170303/evmisc-312)
cpu0 at mainbus0
cpu0: Intel(R) Core(TM) i5-5200U CPU @ 2.20GHz, id 0x306d4
cpu0: package 0, core 0, smt 0
pci0 at mainbus0 bus 0: configuration mode 1
pchb0 at pci0 dev 0 function 0: vendor 0b5d product 0666 (rev. 0x00)
virtio0 at pci0 dev 1 function 0
virtio0: Virtio Entropy Device (rev. 0x00)
viornd0 at virtio0: Features: 0x0
virtio0: interrupting at irq 3
virtio1 at pci0 dev 2 function 0
virtio1: Virtio Block Device (rev. 0x00)
ld0 at virtio1: Features: 0x2<SIZE_MAX>
ld0: Clip SEG_MAX from 1024K to 64K
virtio1: interrupting at irq 5
ld0: 20480 MB, 10402 cyl, 64 head, 63 sec, 512 bytes/sect x 41943040 sectors
virtio2 at pci0 dev 3 function 0
virtio2: Virtio Network Device (rev. 0x00)
vioif0 at virtio2: Features: 0x20<MAC>
vioif0: Ethernet address fe:e1:bb:d1:15:a0
virtio2: interrupting at irq 6
vendor 0b5d product 0777 (miscellaneous communications) at pci0 dev 4 function
0 not configured
isa0 at mainbus0
[ Boot stops here and enter brings me back to the console ]
The messages from vmd -dvvvv are the following:
vm_opentty: vm netbsd tty /dev/ttypd uid 1000 gid 4 mode 620
vm_register: registering vm 5
vm_priv_ifconfig: interface tap0 description vm5-if0-netbsd
vm_priv_ifconfig: interface tap0 address 100.64.5.2/31
netbsd: started vm 5 successfully, tty /dev/ttypd
loadfile_bios: loaded BIOS image
run_vm: initializing hardware for vm netbsd
pic_set_elcr: setting level triggered mode for irq 3
pic_set_elcr: setting level triggered mode for irq 5
pic_set_elcr: setting level triggered mode for irq 6
virtio_init: vm "netbsd" vio0 lladdr fe:e1:bb:d1:7c:d0, local
pic_set_elcr: setting level triggered mode for irq 7
run_vm: starting vcpu threads for vm netbsd
vcpu_reset: resetting vcpu 0 for vm 11
run_vm: waiting on events for VM netbsd
i8259_write_datareg: master pic, reset IRQ vector to 0x8
i8259_write_datareg: slave pic, reset IRQ vector to 0x70
vcpu_exit_i8253: channel 0 reset, mode=2, start=65535
virtio_blk_io: device reset
vcpu_process_com_lcr: set baudrate = 115200
vcpu_process_com_lcr: set baudrate = 9600
vcpu_process_com_lcr: set baudrate = 9600
i8259_write_datareg: master pic, reset IRQ vector to 0x20
i8259_write_datareg: slave pic, reset IRQ vector to 0x28
vcpu_exit_i8253: channel 0 reset, mode=2, start=11932
virtio_blk_io: device reset
virtio_net_io: device reset
vcpu_run_loop: vm 11 / vcpu 0 run ioctl failed: Bad address
vmm_sighdlr: handling signal 20
vmm_sighdlr: terminated vm netbsd (id 5)
vm_remove: vmm vmm_sighdlr removing vm 5 from running config
vm_stop: vmm vmm_sighdlr stopping vm 5
vm_stop: parent vmd_dispatch_vmm stopping vm 5
dmesg of my system:
OpenBSD 6.4-beta (GENERIC.MP) #299: Mon Sep 17 18:30:44 MDT 2018
[email protected]:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 12573237248 (11990MB)
avail mem = 12182913024 (11618MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.7 @ 0x9cbfd000 (65 entries)
bios0: vendor LENOVO version "JBET67WW (1.31 )" date 12/14/2017
bios0: LENOVO 20BX0049GE
acpi0 at bios0: rev 2
acpi0: sleep states S0 S3 S4 S5
acpi0: tables DSDT FACP SLIC ASF! HPET ECDT APIC MCFG SSDT SSDT SSDT SSDT SSDT
SSDT SSDT SSDT SSDT PCCT SSDT TCPA SSDT
UEFI MSDM BATB FPDT UEFI DMAR
acpi0: wakeup devices LID_(S4) SLPB(S3) IGBE(S4) EXP2(S4) XHCI(S3) EHC1(S3)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpihpet0 at acpi0: 14318179 Hz
acpiec0 at acpi0
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Core(TM) i5-5200U CPU @ 2.20GHz, 2095.50 MHz, 06-3d-04
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,RDSEED,ADX,SMAP,PT,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,MELTDOWN
cpu0: 256KB 64b/line 8-way L2 cache
cpu0: smt 0, core 0, package 0
mtrr: Pentium Pro MTRR support, 10 var ranges, 88 fixed ranges
cpu0: apic clock running at 99MHz
cpu0: mwait min=64, max=64, C-substates=0.2.1.2.4.1.1.1, IBE
cpu1 at mainbus0: apid 1 (application processor)
cpu1: Intel(R) Core(TM) i5-5200U CPU @ 2.20GHz, 2095.16 MHz, 06-3d-04
cpu1:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,RDSEED,ADX,SMAP,PT,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,MELTDOWN
cpu1: 256KB 64b/line 8-way L2 cache
cpu1: smt 1, core 0, package 0
cpu2 at mainbus0: apid 2 (application processor)
cpu2: Intel(R) Core(TM) i5-5200U CPU @ 2.20GHz, 2095.16 MHz, 06-3d-04
cpu2:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,RDSEED,ADX,SMAP,PT,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,MELTDOWN
cpu2: 256KB 64b/line 8-way L2 cache
cpu2: smt 0, core 1, package 0
cpu3 at mainbus0: apid 3 (application processor)
cpu3: Intel(R) Core(TM) i5-5200U CPU @ 2.20GHz, 2095.16 MHz, 06-3d-04
cpu3:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,RDSEED,ADX,SMAP,PT,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,MELTDOWN
cpu3: 256KB 64b/line 8-way L2 cache
cpu3: smt 1, core 1, package 0
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 40 pins
acpimcfg0 at acpi0
acpimcfg0: addr 0xf8000000, bus 0-63
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus -1 (PEG_)
acpiprt2 at acpi0: bus 2 (EXP1)
acpiprt3 at acpi0: bus 3 (EXP2)
acpiprt4 at acpi0: bus -1 (EXP3)
acpicpu0 at acpi0: C3(200@233 mwait.1@0x40), C2(200@148 mwait.1@0x33),
C1(1000@1 mwait.1), PSS
acpicpu1 at acpi0: C3(200@233 mwait.1@0x40), C2(200@148 mwait.1@0x33),
C1(1000@1 mwait.1), PSS
acpicpu2 at acpi0: C3(200@233 mwait.1@0x40), C2(200@148 mwait.1@0x33),
C1(1000@1 mwait.1), PSS
acpicpu3 at acpi0: C3(200@233 mwait.1@0x40), C2(200@148 mwait.1@0x33),
C1(1000@1 mwait.1), PSS
acpipwrres0 at acpi0: PUBS, resource for XHCI, EHC1
acpipwrres1 at acpi0: NVP3, resource for PEG_
acpipwrres2 at acpi0: NVP2, resource for PEG_
acpitz0 at acpi0: critical temperature is 128 degC
acpibtn0 at acpi0: LID_
acpibtn1 at acpi0: SLPB
acpicmos0 at acpi0
acpibat0 at acpi0: BAT0 model "45N1111" serial 16646 type LiP oem "SONY"
acpibat1 at acpi0: BAT1 model "45N1777" serial 410 type LION oem "SANYO"
acpiac0 at acpi0: AC unit online
acpithinkpad0 at acpi0
tpm0 at acpi0: TPM_ addr 0xfed40000/0x5000: device 0x0000104a rev 0x4e
"PNP0C14" at acpi0 not configured
"PNP0C14" at acpi0 not configured
"PNP0C14" at acpi0 not configured
"INT340F" at acpi0 not configured
acpivideo0 at acpi0: VID_
acpivout at acpivideo0 not configured
cpu0: Enhanced SpeedStep 2095 MHz: speeds: 2201, 2200, 2100, 2000, 1800, 1700,
1600, 1500, 1300, 1200, 1100, 1000, 900, 700, 600, 500 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel Core 5G Host" rev 0x09
inteldrm0 at pci0 dev 2 function 0 "Intel HD Graphics 5500" rev 0x09
drm0 at inteldrm0
inteldrm0: msi
inteldrm0: 1920x1080, 32bpp
error: [drm:pid0:intel_dp_link_training_clock_recovery] *ERROR* too many full
retries, give up
Unclaimed register detected before reading register 0x64040
wsdisplay0 at inteldrm0 mux 1: console (std, vt100 emulation)
wsdisplay0: screen 1-5 added (std, vt100 emulation)
azalia0 at pci0 dev 3 function 0 "Intel Core 5G HD Audio" rev 0x09: msi
xhci0 at pci0 dev 20 function 0 "Intel 9 Series xHCI" rev 0x03: msi, xHCI 1.0
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev 3.00/1.00
addr 1
"Intel 9 Series MEI" rev 0x03 at pci0 dev 22 function 0 not configured
em0 at pci0 dev 25 function 0 "Intel I218-V" rev 0x03: msi, address
50:7b:9d:73:aa:8a
azalia1 at pci0 dev 27 function 0 "Intel 9 Series HD Audio" rev 0x03: msi
azalia1: codecs: Realtek ALC292
audio0 at azalia1
ppb0 at pci0 dev 28 function 0 "Intel 9 Series PCIE" rev 0xe3: msi
pci1 at ppb0 bus 2
rtsx0 at pci1 dev 0 function 0 "Realtek RTS5227 Card Reader" rev 0x01: msi
sdmmc0 at rtsx0: 4-bit, dma
ppb1 at pci0 dev 28 function 1 "Intel 9 Series PCIE" rev 0xe3: msi
pci2 at ppb1 bus 3
iwm0 at pci2 dev 0 function 0 "Intel Dual Band Wireless-AC 8265" rev 0x78, msi
ehci0 at pci0 dev 29 function 0 "Intel 9 Series USB" rev 0x03: apic 2 int 23
usb1 at ehci0: USB revision 2.0
uhub1 at usb1 configuration 1 interface 0 "Intel EHCI root hub" rev 2.00/1.00
addr 1
pcib0 at pci0 dev 31 function 0 "Intel 9 Series LPC" rev 0x03
ahci0 at pci0 dev 31 function 2 "Intel 9 Series AHCI" rev 0x03: msi, AHCI 1.3
ahci0: port 0: 6.0Gb/s
scsibus1 at ahci0: 32 targets
sd0 at scsibus1 targ 0 lun 0: <ATA, Crucial_CT525MX3, M0C> SCSI3 0/direct fixed
naa.500a075118011ab4
sd0: 500786MB, 512 bytes/sector, 1025610768 sectors, thin
ichiic0 at pci0 dev 31 function 3 "Intel 9 Series SMBus" rev 0x03: apic 2 int 18
iic0 at ichiic0
pchtemp0 at pci0 dev 31 function 6 "Intel 9 Series Thermal" rev 0x03
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5 irq 1 irq 12
pckbdprobe: reset response 0x0
pms0 at pckbc0 (aux slot)
wsmouse0 at pms0 mux 0
wsmouse1 at pms0 mux 0
pms0: Synaptics clickpad, firmware 8.1, 0x1e2b1 0x943300
pckbd0 at pckbc0 (kbd slot)
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
vmm0 at mainbus0: VMX/EPT
uhub2 at uhub1 port 1 configuration 1 interface 0 "Intel Rate Matching Hub" rev
2.00/0.03 addr 2
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
sd1 at scsibus3 targ 1 lun 0: <OPENBSD, SR CRYPTO, 006> SCSI2 0/direct fixed
sd1: 500783MB, 512 bytes/sector, 1025605073 sectors
root on sd1a (df069b96c6c962d9.a) swap on sd1b dump on sd1b
