I had attached the umodem serial console of my OD1000 to the free USB port
on my cubox and it had worked just fine when I upgraded the OD1000 to the
July 19 snapshot. The cubox was running this at that time:
OpenBSD 6.3-current (GENERIC) #40: Fri May 25 13:29:14 MDT 2018
Now, the cubox is running
OpenBSD 6.4 (GENERIC) #68: Sat Oct 6 22:56:37 MDT 2018
...and running 'cu -l cuaU0 -s 115200' reproducibly triggers a panic:
panic: ehci_device_clear_toggle: queue active
Stopped at db_enter: ldrb r15, [r15, r15, ror r15]!
TID PID UID PRFLAGS PFLAGS CPU COMMAND
db_enter
rlv=0xc054ab80 rfp=0xce7bce18
ehci_device_intr_done
rlv=0xc05b4b2c rfp=0xce7bce40
usbd_clear_endpoint_stall_async+0x3c
rlv=0xc05dedf0 rfp=0xce7bce70
ucomwritecb+0x138
rlv=0xc05b46a4 rfp=0xce7bce90
usb_transfer_complete+0x248
rlv=0xc0549630 rfp=0xce7bceb8
ehci_softintr+0x158
rlv=0xc0738658 rfp=0xce7bced8
softintr_dispatch+0x88
rlv=0xc034b120 rfp=0xce7bcf00
arm_do_pending_intr+0xd4
rlv=0xc03a1618 rfp=0xce7bcf28
ampintc_irq_handler+0x188
rlv=0xc04020f8 rfp=0xce7bcfa8
irq_entry+0x78
rlv=0xc04f0420 rfp=0xc09c1f48
Bad frame pointer: 0xc09c1f48
Full dmesg below. Upgrade to current snap and try again? ddb pokery?
Philip
OpenBSD 6.4 (GENERIC) #68: Sat Oct 6 22:56:37 MDT 2018
[email protected]:/usr/src/sys/arch/armv7/compile/GENERIC
real mem = 2147483648 (2048MB)
avail mem = 2095984640 (1998MB)
mainbus0 at root: SolidRun Cubox-i Dual/Quad
cpu0 at mainbus0: ARM Cortex-A9 r2p10 (ARMv7)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
cortex0 at mainbus0
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 7 waymask: 0x0000000f
imxtemp0 at mainbus0simplebus0 at mainbus0: "soc"
ampintc0 at simplebus0 nirq 160, ncpu 4: "interrupt-controller"
simplebus1 at simplebus0: "aips-bus"
imxccm0 at simplebus1
imxanatop0 at simplebus1
syscon0 at simplebus1: "snvs"
imxrtc0 at syscon0
syscon1 at simplebus1: "iomuxc-gpr"
imxiomuxc0 at simplebus1
simplebus2 at simplebus1: "spba-bus"
imxuart0 at simplebus2: console
imxgpio0 at simplebus1
imxgpio1 at simplebus1
imxgpio2 at simplebus1
imxgpio3 at simplebus1
imxgpio4 at simplebus1
imxgpio5 at simplebus1
imxgpio6 at simplebus1
imxdog0 at simplebus1
simplebus3 at simplebus1: "anatop"
imxgpc0 at simplebus1
simplebus4 at simplebus0: "aips-bus"
syscon2 at simplebus4: "ocotp"
imxehci0 at simplebus4
usb0 at imxehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "i.MX EHCI root hub" rev 2.00/1.00
addr 1
imxehci1 at simplebus4
usb1 at imxehci1: USB revision 2.0
uhub1 at usb1 configuration 1 interface 0 "i.MX EHCI root hub" rev 2.00/1.00
addr 1
fec0 at simplebus4
fec0: address d0:63:b4:00:74:d0
atphy0 at fec0 phy 0: AR8035 10/100/1000 PHY, rev. 2
imxesdhc0 at simplebus4
imxesdhc0: 198 MHz base clock
sdmmc0 at imxesdhc0: 4-bit, sd high-speed, mmc high-speed, dma
imxesdhc1 at simplebus4
imxesdhc1: 198 MHz base clock
sdmmc1 at imxesdhc1: 4-bit, sd high-speed, mmc high-speed, dma
imxiic0 at simplebus4
iic0 at imxiic0
imxiic1 at simplebus4
iic1 at imxiic1
pcfrtc0 at iic1 addr 0x68: battery ok
imxuart1 at simplebus4
imxahci0 at simplebus0: AHCI 1.3
imxahci0: port 0: 3.0Gb/s
scsibus0 at imxahci0: 32 targets
sd0 at scsibus0 targ 0 lun 0: <ATA, OCZ-AGILITY3, 2.15> SCSI3 0/direct fixed
naa.5e83a97e097b5eee
sd0: 57241MB, 512 bytes/sector, 117231408 sectors, thin
scsibus1 at sdmmc1: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <SD/MMC, SL08G, 0080> SCSI2 0/direct removable
sd1: 7580MB, 512 bytes/sector, 15523840 sectors
bwfm0 at sdmmc0 function 1
manufacturer 0x02d0, product 0x4330 at sdmmc0 function 2 not configured
umodem0 at uhub1 port 1 configuration 1 interface 0 "SoftIron, Inc. OverDrive
1000" rev 2.00/1.02 addr 2
umodem0: data interface 1, has no CM over data, has break
umodem0: status change notification available
ucom0 at umodem0
ugen0 at uhub1 port 1 configuration 1 "SoftIron, Inc. OverDrive 1000" rev
2.00/1.02 addr 2
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
bootfile: sd0a:/bsd
boot device: sd0
root on sd1a (378ff7368c1bd675.a) swap on sd1b dump on sd1b
WARNING: / was not properly unmounted
