Am 23.11.19 um 11:34 schrieb Darren Tucker:
so real hardware copying over the same network path to the same
destination has the same problem.
Correct.
so a direct connection between source and destination worked OK.
Correct.
so copying from the original source over the same network path to a
new destination has the same problem.
Correct.
More graphical :-)
Ctrl ... WAN ... FW
6.6 --- scp --> 6.6 => problem
6.4 --- scp --> 6.6 => no problem
PC ... WAN ... FW
6.6 --- scp --> 6.6 => problem
FW ... LAN ... PC (same as above)
6.6 <- scp -- 6.6 => no problem
Ctrl ... WAN ... FW ... LAN ... PC
6.6 ---------- scp ---------> 6.6 => problem
Sounds like it's something specific to this network path. What's on it?
Good question … at least two Cisco-routers, maybe some hardware from
another ISP, connection via fibre or copper. I'm trying to figure out
the differences and commonalities from the outposts, which work and
which don't.
6 months worth of development.
Ok, stupid question. I'm sorry about that.
Some suggestions:
a) you could tell us which ciphers you saw for the problematic and
working connections.
I attached two scp-logfiles, one from a working and one not working.
They look the same, except from a few access tries to id-files that
doesn't exist (at the beginning).
b) you could also install Portable OpenSSH 8.0 on your 6.6 system and
test copying to it. That was the version of OpenSSH that shipped with
6.5 (likewise OpenSSH 7.9 that shipped with 6.4). That would narrow
it down to whether or not it's OpenSSH or some other part of the
system.
I installed crisscross *):
On OpenBSD 6.6:
- OpenSSH 7.9 worked NOT, but I've got a different error message after a
few seconds of the copy:
packet_write_poll: Connection to 10.25.0.253 port 22: Permission denied
lost connection
- OpenSSH 8.0 worked NOT, old error message:
client_loop: send disconnect: Broken pipe
lost connection
On OpenBSD 6.4:
- OpenSSH 8.0 worked fine without problems.
c) ship a large test file via netcat to a netcat listener over the
same network paths and compare sha256sums of source and destination.
If you can reproduce a problem without ssh that'll narrow it down.
I've copied a lot of bits through the cable without any problems. The
checksum was always ok.
d) compare the ifconfigs for the 6.4 host and the 6.6 host and see if
anything is different.
ifconfig -a from 6.4 and 6.6 looks exactly the same. The config-files
are of course the same, nothing has happend during the upgrade.
The dmesg says it's from the VM controller not the hardware firewalls.
I don't think we've seen a dmesg from a firewall.
I've attached a dmesg from the 6.6 firewall, which I used as test target
all the time. The PC from the test above is the same hardware model.
Thank you and kind regards,
Illya Meyer
*) I hope, my installation was right (example from 8.0 on 6.4)
./configure --prefix=/usr/local/8.0
make
make install
cd /usr/local/8.0/bin
./ssh -V
OpenSSH_8.0p1, LibreSSL 2.8.2
./scp <source> <dest>
OpenBSD 6.6 (GENERIC.MP) #0: Mon Nov 18 14:16:34 CET 2019
[email protected]:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 4163919872 (3971MB)
avail mem = 4025024512 (3838MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 3.0 @ 0xebfd0 (49 entries)
bios0: vendor American Megatrends Inc. version "5.6.5" date 12/13/2016
bios0: Thomas-Krenn.AG Default string
acpi0 at bios0: ACPI 5.0
acpi0: sleep states S0 S3 S4 S5
acpi0: tables DSDT FACP APIC FPDT FIDT MCFG LPIT HPET SSDT SSDT SSDT UEFI
acpi0: wakeup devices PS2K(S3) PS2M(S3) XHC1(S4) PXSX(S4) PXSX(S4) PXSX(S4)
PXSX(S4) PWRB(S0)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Celeron(R) CPU N2930 @ 1.83GHz, 1833.75 MHz, 06-37-08
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RDRAND,NXE,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,TSC_ADJUST,SMEP,ERMS,MD_CLEAR,IBRS,IBPB,STIBP,SENSOR,ARAT,MELTDOWN
cpu0: 1MB 64b/line 16-way L2 cache
cpu0: smt 0, core 0, package 0
mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
cpu0: apic clock running at 83MHz
cpu0: mwait min=64, max=64, C-substates=0.2.0.0.0.0.3.3, IBE
cpu1 at mainbus0: apid 2 (application processor)
cpu1: Intel(R) Celeron(R) CPU N2930 @ 1.83GHz, 1833.34 MHz, 06-37-08
cpu1:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RDRAND,NXE,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,TSC_ADJUST,SMEP,ERMS,MD_CLEAR,IBRS,IBPB,STIBP,SENSOR,ARAT,MELTDOWN
cpu1: 1MB 64b/line 16-way L2 cache
cpu1: smt 0, core 1, package 0
cpu2 at mainbus0: apid 4 (application processor)
cpu2: Intel(R) Celeron(R) CPU N2930 @ 1.83GHz, 1833.36 MHz, 06-37-08
cpu2:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RDRAND,NXE,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,TSC_ADJUST,SMEP,ERMS,MD_CLEAR,IBRS,IBPB,STIBP,SENSOR,ARAT,MELTDOWN
cpu2: 1MB 64b/line 16-way L2 cache
cpu2: smt 0, core 2, package 0
cpu3 at mainbus0: apid 6 (application processor)
cpu3: Intel(R) Celeron(R) CPU N2930 @ 1.83GHz, 1833.35 MHz, 06-37-08
cpu3:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RDRAND,NXE,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,TSC_ADJUST,SMEP,ERMS,MD_CLEAR,IBRS,IBPB,STIBP,SENSOR,ARAT,MELTDOWN
cpu3: 1MB 64b/line 16-way L2 cache
cpu3: smt 0, core 3, package 0
ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 87 pins
acpimcfg0 at acpi0
acpimcfg0: addr 0xe0000000, bus 0-255
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (RP01)
acpiprt2 at acpi0: bus 2 (RP02)
acpiprt3 at acpi0: bus 3 (RP03)
acpiprt4 at acpi0: bus 4 (RP04)
acpiec0 at acpi0: not present
acpicpu0 at acpi0: C1(@1 halt!), PSS
acpicpu1 at acpi0: C1(@1 halt!), PSS
acpicpu2 at acpi0: C1(@1 halt!), PSS
acpicpu3 at acpi0: C1(@1 halt!), PSS
acpipwrres0 at acpi0: PLPE
acpipwrres1 at acpi0: PLPE
acpipwrres2 at acpi0: USBC, resource for EHC1, OTG1
acpipwrres3 at acpi0: CLK0, resource for CAM1
acpipwrres4 at acpi0: CLK1, resource for CAM0, CAM2
acpicmos0 at acpi0
acpipci0 at acpi0 PCI0: 0x00000010 0x00000011 0x00000000
"DMA0F28" at acpi0 not configured
acpibtn0 at acpi0: PWRB
acpibtn1 at acpi0: SLPB
"INTCF0B" at acpi0 not configured
"INTCF1A" at acpi0 not configured
"INTCF1C" at acpi0 not configured
"SMO91D0" at acpi0 not configured
"MXT3432" at acpi0 not configured
acpivideo0 at acpi0: GFX0
cpu0: using VERW MDS workaround
cpu0: Enhanced SpeedStep 1833 MHz: speeds: 1827, 1826, 1660, 1494, 1328, 1162,
996, 830, 498 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel Bay Trail Host" rev 0x0e
inteldrm0 at pci0 dev 2 function 0 "Intel Bay Trail Video" rev 0x0e
drm0 at inteldrm0
inteldrm0: msi
ahci0 at pci0 dev 19 function 0 "Intel Bay Trail AHCI" rev 0x0e: msi, AHCI 1.3
ahci0: port 0: 3.0Gb/s
scsibus1 at ahci0: 32 targets
sd0 at scsibus1 targ 0 lun 0: <ATA, TS32GMSA370, N112>
t10.ATA_TS32GMSA370_D957300252_
sd0: 30533MB, 512 bytes/sector, 62533296 sectors, thin
xhci0 at pci0 dev 20 function 0 "Intel Bay Trail xHCI" rev 0x0e: msi, xHCI 1.0
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev 3.00/1.00
addr 1
"Intel Bay Trail TXE" rev 0x0e at pci0 dev 26 function 0 not configured
azalia0 at pci0 dev 27 function 0 "Intel Bay Trail HD Audio" rev 0x0e: msi
azalia0: codecs: Realtek ALC662, Intel/0x2882, using Realtek ALC662
audio0 at azalia0
ppb0 at pci0 dev 28 function 0 "Intel Bay Trail PCIE" rev 0x0e: msi
pci1 at ppb0 bus 1
ppb1 at pci0 dev 28 function 1 "Intel Bay Trail PCIE" rev 0x0e: msi
pci2 at ppb1 bus 2
ppb2 at pci0 dev 28 function 2 "Intel Bay Trail PCIE" rev 0x0e: msi
pci3 at ppb2 bus 3
em0 at pci3 dev 0 function 0 "Intel 82583V" rev 0x00: msi, address
00:30:18:06:9f:40
ppb3 at pci0 dev 28 function 3 "Intel Bay Trail PCIE" rev 0x0e: msi
pci4 at ppb3 bus 4
em1 at pci4 dev 0 function 0 "Intel 82583V" rev 0x00: msi, address
00:30:18:06:9f:3f
pcib0 at pci0 dev 31 function 0 "Intel Bay Trail LPC" rev 0x0e
ichiic0 at pci0 dev 31 function 3 "Intel Bay Trail SMBus" rev 0x0e: apic 1 int
18
iic0 at ichiic0
spdmem0 at iic0 addr 0x50: 4GB DDR3 SDRAM PC3-12800 SO-DIMM
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
pckbc0 at isa0 port 0x60/5 irq 1 irq 12
pckbd0 at pckbc0 (kbd slot)
wskbd0 at pckbd0: console keyboard
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
vmm0 at mainbus0: VMX/EPT (using slow L1TF mitigation)
uhub1 at uhub0 port 4 configuration 1 interface 0 "Genesys Logic USB2.0 Hub"
rev 2.00/88.32 addr 2
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
root on sd0a (ea44963b0108c50a.a) swap on sd0b dump on sd0b
inteldrm0: 1024x768, 32bpp
wsdisplay0 at inteldrm0 mux 1: console (std, vt100 emulation), using wskbd0
wsdisplay0: screen 1-5 added (std, vt100 emulation)
Executing: program /usr/bin/ssh host feuerwand.ags.lokal, user root, command scp -v -d -t /var/rel
OpenSSH_7.9, LibreSSL 2.8.2
debug1: Reading configuration data /etc/ssh/ssh_config
debug2: resolving "feuerwand.ags.lokal" port 22
debug2: ssh_connect_direct
debug1: Connecting to feuerwand.ags.lokal [10.25.0.253] port 22.
debug1: Connection established.
debug1: identity file /root/.ssh/id_rsa type -1
debug1: identity file /root/.ssh/id_rsa-cert type -1
debug1: identity file /root/.ssh/id_dsa type -1
debug1: identity file /root/.ssh/id_dsa-cert type -1
debug1: identity file /root/.ssh/id_ecdsa type -1
debug1: identity file /root/.ssh/id_ecdsa-cert type -1
debug1: identity file /root/.ssh/id_ed25519 type -1
debug1: identity file /root/.ssh/id_ed25519-cert type -1
debug1: identity file /root/.ssh/id_xmss type -1
debug1: identity file /root/.ssh/id_xmss-cert type -1
debug1: Local version string SSH-2.0-OpenSSH_7.9
debug1: Remote protocol version 2.0, remote software version OpenSSH_8.1
debug1: match: OpenSSH_8.1 pat OpenSSH* compat 0x04000000
debug2: fd 3 setting O_NONBLOCK
debug1: Authenticating to feuerwand.ags.lokal:22 as 'root'
debug3: hostkeys_foreach: reading file "/root/.ssh/known_hosts"
debug3: record_hostkey: found key type ECDSA in file /root/.ssh/known_hosts:58
debug3: load_hostkeys: loaded 1 keys from feuerwand.ags.lokal
debug3: order_hostkeyalgs: prefer hostkeyalgs: [email protected],[email protected],[email protected],ecdsa-sha2-nistp256,ecdsa-sha2-nistp384,ecdsa-sha2-nistp521
debug3: send packet: type 20
debug1: SSH2_MSG_KEXINIT sent
debug3: receive packet: type 20
debug1: SSH2_MSG_KEXINIT received
debug2: local client KEXINIT proposal
debug2: KEX algorithms: curve25519-sha256,[email protected],ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha256,diffie-hellman-group16-sha512,diffie-hellman-group18-sha512,diffie-hellman-group14-sha256,diffie-hellman-group14-sha1,ext-info-c
debug2: host key algorithms: [email protected],[email protected],[email protected],ecdsa-sha2-nistp256,ecdsa-sha2-nistp384,ecdsa-sha2-nistp521,[email protected],[email protected],[email protected],[email protected],ssh-ed25519,rsa-sha2-512,rsa-sha2-256,ssh-rsa
debug2: ciphers ctos: [email protected],aes128-ctr,aes192-ctr,aes256-ctr,[email protected],[email protected]
debug2: ciphers stoc: [email protected],aes128-ctr,aes192-ctr,aes256-ctr,[email protected],[email protected]
debug2: MACs ctos: [email protected],[email protected],[email protected],[email protected],[email protected],[email protected],[email protected],hmac-sha2-256,hmac-sha2-512,hmac-sha1
debug2: MACs stoc: [email protected],[email protected],[email protected],[email protected],[email protected],[email protected],[email protected],hmac-sha2-256,hmac-sha2-512,hmac-sha1
debug2: compression ctos: none,[email protected],zlib
debug2: compression stoc: none,[email protected],zlib
debug2: languages ctos:
debug2: languages stoc:
debug2: first_kex_follows 0
debug2: reserved 0
debug2: peer server KEXINIT proposal
debug2: KEX algorithms: curve25519-sha256,[email protected],ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha256,diffie-hellman-group16-sha512,diffie-hellman-group18-sha512,diffie-hellman-group14-sha256,diffie-hellman-group14-sha1
debug2: host key algorithms: rsa-sha2-512,rsa-sha2-256,ssh-rsa,ecdsa-sha2-nistp256,ssh-ed25519
debug2: ciphers ctos: [email protected],aes128-ctr,aes192-ctr,aes256-ctr,[email protected],[email protected]
debug2: ciphers stoc: [email protected],aes128-ctr,aes192-ctr,aes256-ctr,[email protected],[email protected]
debug2: MACs ctos: [email protected],[email protected],[email protected],[email protected],[email protected],[email protected],[email protected],hmac-sha2-256,hmac-sha2-512,hmac-sha1
debug2: MACs stoc: [email protected],[email protected],[email protected],[email protected],[email protected],[email protected],[email protected],hmac-sha2-256,hmac-sha2-512,hmac-sha1
debug2: compression ctos: none,[email protected]
debug2: compression stoc: none,[email protected]
debug2: languages ctos:
debug2: languages stoc:
debug2: first_kex_follows 0
debug2: reserved 0
debug1: kex: algorithm: curve25519-sha256
debug1: kex: host key algorithm: ecdsa-sha2-nistp256
debug1: kex: server->client cipher: [email protected] MAC: <implicit> compression: none
debug1: kex: client->server cipher: [email protected] MAC: <implicit> compression: none
debug3: send packet: type 30
debug1: expecting SSH2_MSG_KEX_ECDH_REPLY
debug3: receive packet: type 31
debug1: Server host key: ecdsa-sha2-nistp256 SHA256:[...]
debug3: hostkeys_foreach: reading file "/root/.ssh/known_hosts"
debug3: record_hostkey: found key type ECDSA in file /root/.ssh/known_hosts:58
debug3: load_hostkeys: loaded 1 keys from feuerwand.ags.lokal
debug3: hostkeys_foreach: reading file "/root/.ssh/known_hosts"
debug3: record_hostkey: found key type ECDSA in file /root/.ssh/known_hosts:57
debug3: load_hostkeys: loaded 1 keys from 10.25.0.253
debug1: Host 'feuerwand.ags.lokal' is known and matches the ECDSA host key.
debug1: Found key in /root/.ssh/known_hosts:58
debug3: send packet: type 21
debug2: set_newkeys: mode 1
debug1: rekey after 134217728 blocks
debug1: SSH2_MSG_NEWKEYS sent
debug1: expecting SSH2_MSG_NEWKEYS
debug3: receive packet: type 21
debug1: SSH2_MSG_NEWKEYS received
debug2: set_newkeys: mode 0
debug1: rekey after 134217728 blocks
debug1: Will attempt key: /root/.ssh/id_rsa
debug1: Will attempt key: /root/.ssh/id_dsa
debug1: Will attempt key: /root/.ssh/id_ecdsa
debug1: Will attempt key: /root/.ssh/id_ed25519
debug1: Will attempt key: /root/.ssh/id_xmss
debug2: pubkey_prepare: done
debug3: send packet: type 5
debug3: receive packet: type 7
debug1: SSH2_MSG_EXT_INFO received
debug1: kex_input_ext_info: server-sig-algs=<ssh-ed25519,ssh-rsa,rsa-sha2-256,rsa-sha2-512,ssh-dss,ecdsa-sha2-nistp256,ecdsa-sha2-nistp384,ecdsa-sha2-nistp521>
debug3: receive packet: type 6
debug2: service_accept: ssh-userauth
debug1: SSH2_MSG_SERVICE_ACCEPT received
debug3: send packet: type 50
debug3: receive packet: type 51
debug1: Authentications that can continue: publickey,password,keyboard-interactive
debug3: start over, passed a different list publickey,password,keyboard-interactive
debug3: preferred publickey,keyboard-interactive,password
debug3: authmethod_lookup publickey
debug3: remaining preferred: keyboard-interactive,password
debug3: authmethod_is_enabled publickey
debug1: Next authentication method: publickey
debug1: Trying private key: /root/.ssh/id_rsa
debug3: sign_and_send_pubkey: RSA SHA256:[...]
debug3: sign_and_send_pubkey: signing using rsa-sha2-512
debug3: send packet: type 50
debug2: we sent a publickey packet, wait for reply
debug3: receive packet: type 52
debug1: Authentication succeeded (publickey).
Authenticated to feuerwand.ags.lokal ([10.25.0.253]:22).
debug2: fd 4 setting O_NONBLOCK
debug2: fd 5 setting O_NONBLOCK
debug2: fd 6 setting O_NONBLOCK
debug1: channel 0: new [client-session]
debug3: ssh_session2_open: channel_new: 0
debug2: channel 0: send open
debug3: send packet: type 90
debug1: Requesting [email protected]
debug3: send packet: type 80
debug1: Entering interactive session.
debug1: pledge: network
debug3: receive packet: type 80
debug1: client_input_global_request: rtype [email protected] want_reply 0
debug3: receive packet: type 4
debug1: Remote: /root/.ssh/authorized_keys:1: key options: agent-forwarding port-forwarding pty user-rc x11-forwarding
debug3: receive packet: type 91
debug2: channel_input_open_confirmation: channel 0: callback start
debug2: fd 3 setting TCP_NODELAY
debug3: ssh_packet_set_tos: set IP_TOS 0x20
debug2: client_session2_setup: id 0
debug1: Sending command: scp -v -d -t /var/rel
debug2: channel 0: request exec confirm 1
debug3: send packet: type 98
debug2: channel_input_open_confirmation: channel 0: callback done
debug2: channel 0: open confirm rwindow 0 rmax 32768
debug2: channel 0: rcvd adjust 2097152
debug3: receive packet: type 99
debug2: channel_input_status_confirm: type 99 id 0
debug2: exec request accepted on channel 0
Sending file modes: C0644 1989 SHA256
debug2: channel 0: rcvd ext data 24
Sink: C0644 1989 SHA256
debug2: channel 0: written 24 to efd 6
Sending file modes: C0644 2141 SHA256.sig
debug2: channel 0: rcvd ext data 28
Sink: C0644 2141 SHA256.sig
debug2: channel 0: written 28 to efd 6
Sending file modes: C0644 248077818 base66.tgz
debug2: channel 0: rcvd ext data 33
Sink: C0644 248077818 base66.tgz
debug2: channel 0: written 33 to efd 6
debug2: channel 0: rcvd adjust 102503
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
[...]
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 122363
Sending file modes: C0644 18688685 bsd
debug2: channel 0: rcvd ext data 25
Sink: C0644 18688685 bsd
debug2: channel 0: written 25 to efd 6
debug2: channel 0: rcvd adjust 98323
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
[...]
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 109230
Sending file modes: C0644 18776067 bsd.mp
debug2: channel 0: rcvd ext data 28
Sink: C0644 18776067 bsd.mp
debug2: channel 0: written 28 to efd 6
debug2: channel 0: rcvd adjust 98326
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
[...]
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
Sending file modes: C0644 10299545 bsd.rd
debug2: channel 0: rcvd ext data 28
Sink: C0644 10299545 bsd.rd
debug2: channel 0: written 28 to efd 6
debug2: channel 0: rcvd adjust 98330
debug2: channel 0: rcvd adjust 114688
debug2: channel 0: rcvd adjust 131072
[...]
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
Sending file modes: C0644 73840308 comp66.tgz
debug2: channel 0: rcvd ext data 32
Sink: C0644 73840308 comp66.tgz
debug2: channel 0: written 32 to efd 6
debug2: channel 0: rcvd adjust 108724
debug2: channel 0: rcvd adjust 131072
[...]
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
Sending file modes: C0644 1687 index.txt
debug2: channel 0: rcvd ext data 27
Sink: C0644 1687 index.txt
debug2: channel 0: written 27 to efd 6
Sending file modes: C0644 120121 log
debug2: channel 0: rcvd ext data 23
Sink: C0644 120121 log
debug2: channel 0: written 23 to efd 6
debug2: channel 0: rcvd adjust 114035
Sending file modes: C0644 7596243 man66.tgz
debug2: channel 0: rcvd ext data 30
Sink: C0644 7596243 man66.tgz
debug2: channel 0: written 30 to efd 6
debug2: channel 0: rcvd adjust 103762
debug2: channel 0: rcvd adjust 114688
debug2: channel 0: rcvd adjust 131072
[...]
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
Sending file modes: C0644 4589888 xshare66.tgz
debug2: channel 0: rcvd ext data 33
Sink: C0644 4589888 xshare66.tgz
debug2: channel 0: written 33 to efd 6
debug2: channel 0: rcvd adjust 108783
debug2: channel 0: rcvd adjust 114688
debug2: channel 0: rcvd adjust 131072
[...]
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: read<=0 rfd 4 len 0
debug2: channel 0: read failed
debug2: channel 0: chan_shutdown_read (i0 o0 sock -1 wfd 4 efd 6 [write])
debug2: channel 0: input open -> drain
debug2: channel 0: ibuf empty
debug2: channel 0: send eof
debug3: send packet: type 96
debug2: channel 0: input drain -> closed
debug3: receive packet: type 96
debug2: channel 0: rcvd eof
debug2: channel 0: output open -> drain
debug2: channel 0: obuf empty
debug2: channel 0: chan_shutdown_write (i3 o1 sock -1 wfd 5 efd 6 [write])
debug2: channel 0: output drain -> closed
debug3: receive packet: type 98
debug1: client_input_channel_req: channel 0 rtype exit-status reply 0
debug3: receive packet: type 97
debug2: channel 0: rcvd close
debug3: channel 0: will not send data after close
debug2: channel 0: almost dead
debug2: channel 0: gc: notify user
debug2: channel 0: gc: user detached
debug2: channel 0: send close
debug3: send packet: type 97
debug2: channel 0: is dead
debug2: channel 0: garbage collecting
debug1: channel 0: free: client-session, nchannels 1
debug3: channel 0: status: The following connections are open:
#0 client-session (t4 r0 i3/0 o3/0 e[write]/0 fd -1/-1/6 sock -1 cc -1)
debug3: send packet: type 1
debug1: fd 0 clearing O_NONBLOCK
debug3: fd 1 is not O_NONBLOCK
debug1: fd 2 clearing O_NONBLOCK
Transferred: sent 382231484, received 61764 bytes, in 81.2 seconds
Bytes per second: sent 4709598.9, received 761.0
debug1: Exit status 0
Executing: program /usr/bin/ssh host feuerwand.ags.lokal, user root, command scp -v -d -t /var/rel/
OpenSSH_8.1, LibreSSL 3.0.2
debug1: Reading configuration data /etc/ssh/ssh_config
debug2: resolving "feuerwand.ags.lokal" port 50
debug2: ssh_connect_direct
debug1: Connecting to feuerwand.ags.lokal [10.25.0.253] port 50.
debug1: Connection established.
debug1: identity file /root/.ssh/id_rsa type -1
debug1: identity file /root/.ssh/id_rsa-cert type -1
debug1: identity file /root/.ssh/id_dsa type -1
debug1: identity file /root/.ssh/id_dsa-cert type -1
debug1: identity file /root/.ssh/id_ecdsa type -1
debug1: identity file /root/.ssh/id_ecdsa-cert type -1
debug1: identity file /root/.ssh/id_ecdsa_sk type -1
debug1: identity file /root/.ssh/id_ecdsa_sk-cert type -1
debug1: identity file /root/.ssh/id_ed25519 type -1
debug1: identity file /root/.ssh/id_ed25519-cert type -1
debug1: identity file /root/.ssh/id_ed25519_sk type -1
debug1: identity file /root/.ssh/id_ed25519_sk-cert type -1
debug1: identity file /root/.ssh/id_xmss type -1
debug1: identity file /root/.ssh/id_xmss-cert type -1
debug1: Local version string SSH-2.0-OpenSSH_8.1
debug1: Remote protocol version 2.0, remote software version OpenSSH_8.1
debug1: match: OpenSSH_8.1 pat OpenSSH* compat 0x04000000
debug2: fd 3 setting O_NONBLOCK
debug1: Authenticating to feuerwand.ags.lokal:50 as 'root'
debug3: put_host_port: [feuerwand.ags.lokal]:50
debug3: hostkeys_foreach: reading file "/root/.ssh/known_hosts"
debug3: send packet: type 20
debug1: SSH2_MSG_KEXINIT sent
debug3: receive packet: type 20
debug1: SSH2_MSG_KEXINIT received
debug2: local client KEXINIT proposal
debug2: KEX algorithms: curve25519-sha256,[email protected],ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha256,diffie-hellman-group16-sha512,diffie-hellman-group18-sha512,diffie-hellman-group14-sha256,diffie-hellman-group14-sha1,ext-info-c
debug2: host key algorithms: [email protected],[email protected],[email protected],[email protected],[email protected],[email protected],[email protected],ecdsa-sha2-nistp256,ecdsa-sha2-nistp384,ecdsa-sha2-nistp521,ssh-ed25519,rsa-sha2-512,rsa-sha2-256,ssh-rsa
debug2: ciphers ctos: [email protected],aes128-ctr,aes192-ctr,aes256-ctr,[email protected],[email protected]
debug2: ciphers stoc: [email protected],aes128-ctr,aes192-ctr,aes256-ctr,[email protected],[email protected]
debug2: MACs ctos: [email protected],[email protected],[email protected],[email protected],[email protected],[email protected],[email protected],hmac-sha2-256,hmac-sha2-512,hmac-sha1
debug2: MACs stoc: [email protected],[email protected],[email protected],[email protected],[email protected],[email protected],[email protected],hmac-sha2-256,hmac-sha2-512,hmac-sha1
debug2: compression ctos: none,[email protected],zlib
debug2: compression stoc: none,[email protected],zlib
debug2: languages ctos:
debug2: languages stoc:
debug2: first_kex_follows 0
debug2: reserved 0
debug2: peer server KEXINIT proposal
debug2: KEX algorithms: curve25519-sha256,[email protected],ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha256,diffie-hellman-group16-sha512,diffie-hellman-group18-sha512,diffie-hellman-group14-sha256,diffie-hellman-group14-sha1
debug2: host key algorithms: rsa-sha2-512,rsa-sha2-256,ssh-rsa,ecdsa-sha2-nistp256,ssh-ed25519
debug2: ciphers ctos: [email protected],aes128-ctr,aes192-ctr,aes256-ctr,[email protected],[email protected]
debug2: ciphers stoc: [email protected],aes128-ctr,aes192-ctr,aes256-ctr,[email protected],[email protected]
debug2: MACs ctos: [email protected],[email protected],[email protected],[email protected],[email protected],[email protected],[email protected],hmac-sha2-256,hmac-sha2-512,hmac-sha1
debug2: MACs stoc: [email protected],[email protected],[email protected],[email protected],[email protected],[email protected],[email protected],hmac-sha2-256,hmac-sha2-512,hmac-sha1
debug2: compression ctos: none,[email protected]
debug2: compression stoc: none,[email protected]
debug2: languages ctos:
debug2: languages stoc:
debug2: first_kex_follows 0
debug2: reserved 0
debug1: kex: algorithm: curve25519-sha256
debug1: kex: host key algorithm: ecdsa-sha2-nistp256
debug1: kex: server->client cipher: [email protected] MAC: <implicit> compression: none
debug1: kex: client->server cipher: [email protected] MAC: <implicit> compression: none
debug3: send packet: type 30
debug1: expecting SSH2_MSG_KEX_ECDH_REPLY
debug3: receive packet: type 31
debug1: Server host key: ecdsa-sha2-nistp256 SHA256:[...]
debug3: put_host_port: [10.25.0.253]:50
debug3: put_host_port: [feuerwand.ags.lokal]:50
debug3: hostkeys_foreach: reading file "/root/.ssh/known_hosts"
debug3: hostkeys_foreach: reading file "/root/.ssh/known_hosts"
debug1: checking without port identifier
debug3: hostkeys_foreach: reading file "/root/.ssh/known_hosts"
debug3: record_hostkey: found key type ECDSA in file /root/.ssh/known_hosts:58
debug3: load_hostkeys: loaded 1 keys from feuerwand.ags.lokal
debug3: hostkeys_foreach: reading file "/root/.ssh/known_hosts"
debug3: record_hostkey: found key type ECDSA in file /root/.ssh/known_hosts:57
debug3: load_hostkeys: loaded 1 keys from 10.25.0.253
debug1: Host 'feuerwand.ags.lokal' is known and matches the ECDSA host key.
debug1: Found key in /root/.ssh/known_hosts:58
debug1: found matching key w/out port
debug3: send packet: type 21
debug2: set_newkeys: mode 1
debug1: rekey out after 134217728 blocks
debug1: SSH2_MSG_NEWKEYS sent
debug1: expecting SSH2_MSG_NEWKEYS
debug3: receive packet: type 21
debug1: SSH2_MSG_NEWKEYS received
debug2: set_newkeys: mode 0
debug1: rekey in after 134217728 blocks
debug1: Will attempt key: /root/.ssh/id_rsa
debug1: Will attempt key: /root/.ssh/id_dsa
debug1: Will attempt key: /root/.ssh/id_ecdsa
debug1: Will attempt key: /root/.ssh/id_ecdsa_sk
debug1: Will attempt key: /root/.ssh/id_ed25519
debug1: Will attempt key: /root/.ssh/id_ed25519_sk
debug1: Will attempt key: /root/.ssh/id_xmss
debug2: pubkey_prepare: done
debug3: send packet: type 5
debug3: receive packet: type 7
debug1: SSH2_MSG_EXT_INFO received
debug1: kex_input_ext_info: server-sig-algs=<ssh-ed25519,ssh-rsa,rsa-sha2-256,rsa-sha2-512,ssh-dss,ecdsa-sha2-nistp256,ecdsa-sha2-nistp384,ecdsa-sha2-nistp521>
debug3: receive packet: type 6
debug2: service_accept: ssh-userauth
debug1: SSH2_MSG_SERVICE_ACCEPT received
debug3: send packet: type 50
debug3: receive packet: type 51
debug1: Authentications that can continue: publickey,password,keyboard-interactive
debug3: start over, passed a different list publickey,password,keyboard-interactive
debug3: preferred publickey,keyboard-interactive,password
debug3: authmethod_lookup publickey
debug3: remaining preferred: keyboard-interactive,password
debug3: authmethod_is_enabled publickey
debug1: Next authentication method: publickey
debug1: Trying private key: /root/.ssh/id_rsa
debug3: sign_and_send_pubkey: RSA SHA256:[...]
debug3: sign_and_send_pubkey: signing using rsa-sha2-512
debug3: send packet: type 50
debug2: we sent a publickey packet, wait for reply
debug3: receive packet: type 52
debug1: Authentication succeeded (publickey).
Authenticated to feuerwand.ags.lokal ([10.25.0.253]:50).
debug2: fd 4 setting O_NONBLOCK
debug2: fd 5 setting O_NONBLOCK
debug2: fd 6 setting O_NONBLOCK
debug1: channel 0: new [client-session]
debug3: ssh_session2_open: channel_new: 0
debug2: channel 0: send open
debug3: send packet: type 90
debug1: Requesting [email protected]
debug3: send packet: type 80
debug1: Entering interactive session.
debug1: pledge: network
debug3: receive packet: type 80
debug1: client_input_global_request: rtype [email protected] want_reply 0
debug3: receive packet: type 4
debug1: Remote: /root/.ssh/authorized_keys:1: key options: agent-forwarding port-forwarding pty user-rc x11-forwarding
debug3: receive packet: type 91
debug2: channel_input_open_confirmation: channel 0: callback start
debug2: fd 3 setting TCP_NODELAY
debug3: ssh_packet_set_tos: set IP_TOS 0x20
debug2: client_session2_setup: id 0
debug1: Sending command: scp -v -d -t /var/rel/
debug2: channel 0: request exec confirm 1
debug3: send packet: type 98
debug2: channel_input_open_confirmation: channel 0: callback done
debug2: channel 0: open confirm rwindow 0 rmax 32768
debug2: channel 0: rcvd adjust 2097152
debug3: receive packet: type 99
debug2: channel_input_status_confirm: type 99 id 0
debug2: exec request accepted on channel 0
debug2: channel 0: rcvd ext data 25
Environment:
USER=root
debug2: channel 0: written 25 to efd 6
debug2: channel 0: rcvd ext data 232
LOGNAME=root
HOME=/root
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/X11R6/bin:/usr/local/bin:/usr/local/sbin
MAIL=/var/mail/root
SHELL=/bin/ksh
SSH_CLIENT=10.69.0.15 18044 50
SSH_CONNECTION=10.69.0.15 18044 10.25.0.253 50
debug2: channel 0: written 232 to efd 6
Sending file modes: C0644 1989 SHA256
debug2: channel 0: rcvd ext data 24
Sink: C0644 1989 SHA256
debug2: channel 0: written 24 to efd 6
Sending file modes: C0644 2141 SHA256.sig
debug2: channel 0: rcvd ext data 28
Sink: C0644 2141 SHA256.sig
debug2: channel 0: written 28 to efd 6
Sending file modes: C0644 248077818 base66.tgz
debug2: channel 0: rcvd ext data 33
Sink: C0644 248077818 base66.tgz
debug2: channel 0: written 33 to efd 6
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
[...]
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 122363
Sending file modes: C0644 18688685 bsd
debug2: channel 0: rcvd ext data 25
Sink: C0644 18688685 bsd
debug2: channel 0: written 25 to efd 6
debug2: channel 0: rcvd adjust 98323
debug2: channel 0: rcvd adjust 114688
debug2: channel 0: rcvd adjust 114688
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
[...]
debug2: channel 0: rcvd adjust 131072
debug2: channel 0: rcvd adjust 131072
debug3: send packet: type 1
client_loop: send disconnect: Broken pipe
lost connection
