Hi,
I have messing with OpenBSD current on my LinkStar H68K ARM box, based on the
Rockchip RK3568 SOC. Originally it had an unsupported Mediatek wlan card, which
i have replaced it with an intel one i had lying around.
While OBSD recognizes the installed card, it categorically states it is
not-configured, while it supposed to be supported by the iwn driver.
Sadly i did not made any photo about the card i have installed, and the device
is tricky to disassemble, but AFAIR the installed card is 0x8086, 0x088f,
"Intel Centrino Advanced-N 6235. What could cause a device mis-recognition?
Any idea what's going on here?
Best Regards,
--Zoltan
OpenBSD 7.4-current (GENERIC.MP) #40: Wed Jan 10 02:01:40 MST 2024
[email protected]:/usr/src/sys/arch/arm64/compile/GENERIC.MP
real mem = 3959590912 (3776MB)
avail mem = 3755196416 (3581MB)
random: good seed from bootblocks
mainbus0 at root: HINLINK OPC-H68K Board
psci0 at mainbus0: PSCI 1.1, SMCCC 1.2, SYSTEM_SUSPEND
efi0 at mainbus0: UEFI 2.7
efi0: EDK2 rev 0x10000
smbios0 at efi0: SMBIOS 3.3.0
smbios0: vendor EDK2 version "miq" date 12/16/2023
smbios0: Firefly Firefly ROC-RK3568-PC
cpu0 at mainbus0 mpidr 0: ARM Cortex-A55 r2p0
cpu0: 32KB 64b/line 4-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
cpu0: 512KB 64b/line 16-way L2 cache
cpu0:
DP,RDM,Atomic,CRC32,SHA2,SHA1,AES+PMULL,LRCPC,DPB,ASID16,PAN+ATS1E1,LO,HPDS,VH,HAFDBS,SBSS
cpu1 at mainbus0 mpidr 100: ARM Cortex-A55 r2p0
cpu1: 32KB 64b/line 4-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
cpu1: 512KB 64b/line 16-way L2 cache
cpu1:
DP,RDM,Atomic,CRC32,SHA2,SHA1,AES+PMULL,LRCPC,DPB,ASID16,PAN+ATS1E1,LO,HPDS,VH,HAFDBS,SBSS
cpu2 at mainbus0 mpidr 200: ARM Cortex-A55 r2p0
cpu2: 32KB 64b/line 4-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
cpu2: 512KB 64b/line 16-way L2 cache
cpu2:
DP,RDM,Atomic,CRC32,SHA2,SHA1,AES+PMULL,LRCPC,DPB,ASID16,PAN+ATS1E1,LO,HPDS,VH,HAFDBS,SBSS
cpu3 at mainbus0 mpidr 300: ARM Cortex-A55 r2p0
cpu3: 32KB 64b/line 4-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
cpu3: 512KB 64b/line 16-way L2 cache
cpu3:
DP,RDM,Atomic,CRC32,SHA2,SHA1,AES+PMULL,LRCPC,DPB,ASID16,PAN+ATS1E1,LO,HPDS,VH,HAFDBS,SBSS
scmi0 at mainbus0: SCMI 2.0
apm0 at mainbus0
agintc0 at mainbus0 mbi shift 4:4 nirq 352 nredist 4 ipi: 0, 1, 2:
"interrupt-controller"
syscon0 at mainbus0: "syscon"
rkiovd0 at syscon0
syscon1 at mainbus0: "syscon"
syscon2 at mainbus0: "syscon"
syscon3 at mainbus0: "syscon"
syscon4 at mainbus0: "syscon"
syscon5 at mainbus0: "syscon"
syscon6 at mainbus0: "syscon"
rkclock0 at mainbus0: PMUCRU
rkclock1 at mainbus0: CRU
syscon7 at mainbus0: "power-management"
"power-controller" at syscon7 not configured
syscon8 at mainbus0: "qos"
syscon9 at mainbus0: "qos"
syscon10 at mainbus0: "qos"
syscon11 at mainbus0: "qos"
syscon12 at mainbus0: "qos"
syscon13 at mainbus0: "qos"
syscon14 at mainbus0: "qos"
syscon15 at mainbus0: "qos"
syscon16 at mainbus0: "qos"
syscon17 at mainbus0: "qos"
syscon18 at mainbus0: "qos"
syscon19 at mainbus0: "qos"
syscon20 at mainbus0: "qos"
syscon21 at mainbus0: "qos"
syscon22 at mainbus0: "qos"
syscon23 at mainbus0: "qos"
syscon24 at mainbus0: "qos"
syscon25 at mainbus0: "qos"
syscon26 at mainbus0: "qos"
syscon27 at mainbus0: "qos"
syscon28 at mainbus0: "qos"
syscon29 at mainbus0: "qos"
syscon30 at mainbus0: "qos"
syscon31 at mainbus0: "qos"
rkcomphy0 at mainbus0
rkcomphy1 at mainbus0
rkusbphy0 at mainbus0: phy 0
rkusbphy1 at mainbus0: phy 1
rkpinctrl0 at mainbus0: "pinctrl"
rkgpio0 at rkpinctrl0
rkgpio1 at rkpinctrl0
rkgpio2 at rkpinctrl0
rkgpio3 at rkpinctrl0
rkgpio4 at rkpinctrl0
syscon32 at mainbus0: "syscon"
syscon33 at mainbus0: "qos"
syscon34 at mainbus0: "qos"
syscon35 at mainbus0: "qos"
syscon36 at mainbus0: "syscon"
rkpciephy0 at mainbus0
rkcomphy2 at mainbus0
"fit-images" at mainbus0 not configured
"opp-table-0" at mainbus0 not configured
"display-subsystem" at mainbus0 not configured
"firmware" at mainbus0 not configured
"opp-table-1" at mainbus0 not configured
simpleaudio0 at mainbus0
"pmu" at mainbus0 not configured
agtimer0 at mainbus0: 24000 kHz
"xin24m" at mainbus0 not configured
"xin32k" at mainbus0 not configured
"sram" at mainbus0 not configured
xhci0 at mainbus0, xHCI 1.10
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 configuration 1 interface 0 "Generic xHCI root hub" rev 3.00/1.00
addr 1
ehci0 at mainbus0
usb1 at ehci0: USB revision 2.0
uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00
addr 1
ohci0 at mainbus0: version 1.0
ehci1 at mainbus0
usb2 at ehci1: USB revision 2.0
uhub2 at usb2 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00
addr 1
ohci1 at mainbus0: version 1.0
rkiic0 at mainbus0
iic0 at rkiic0
fanpwr0 at iic0 addr 0x1c: TCS4525, 1.15 VDC
rkpmic0 at iic0 addr 0x20: RK809
rkpwm0 at mainbus0rkclock_get_frequency(rkclock0, 13)
: no clock
"gpu" at mainbus0 not configured
"video-codec" at mainbus0 not configured
"iommu" at mainbus0 not configured
"rga" at mainbus0 not configured
"video-codec" at mainbus0 not configured
"iommu" at mainbus0 not configured
dwqe0 at mainbus0 gmac 1: rev 0x51, address 3e:68:a7:8e:7e:25
rgephy0 at dwqe0 phy 0: RTL8169S/8110S/8211 PHY, rev. 6
"vop" at mainbus0 not configured
"iommu" at mainbus0 not configured
"hdmi" at mainbus0 not configured
dwpcie0 at mainbus0
dwmmc0 at mainbus0: 50 MHz base clock
sdmmc0 at dwmmc0: 4-bit, sd high-speed, dma
dwmshc0 at mainbus0
dwmshc0: SDHC 4.20, 200 MHz base clock
sdmmc1 at dwmshc0: 8-bit, sd high-speed, mmc high-speed, dma
"i2s" at mainbus0 not configured
"i2s" at mainbus0 not configured
"dma-controller" at mainbus0 not configured
"dma-controller" at mainbus0 not configured
rkiic1 at mainbus0
iic1 at rkiic1
"watchdog" at mainbus0 not configured
com0 at mainbus0: dw16550, 64 byte fifo
rktemp0 at mainbus0
"saradc" at mainbus0 not configured
ahci0 at mainbus0: AHCI 1.3
scsibus0 at ahci0: 32 targets
dwpcie1 at mainbus0
dwpcie2 at mainbus0
dwqe1 at mainbus0 gmac 0: rev 0x51, address 3e:68:a7:8e:7e:24
rgephy1 at dwqe1 phy 0: RTL8169S/8110S/8211 PHY, rev. 6
rkrng0 at mainbus0: ver 2
"hdmi-con" at mainbus0 not configured
gpiokeys0 at mainbus0: "reset"
gpioleds0 at mainbus0: no LEDs
"vcc12v-dcin" at mainbus0 not configured
"vcc3v3-sys" at mainbus0 not configured
"vcc5v0-sys" at mainbus0 not configured
"vcc5v0-usb" at mainbus0 not configured
"vcc5v0-usb-host" at mainbus0 not configured
"vcc3v3-pcie" at mainbus0 not configured
simpleaudio1 at mainbus0
pwmfan0 at mainbus0
simplefb0 at mainbus0: 3840x2160, 32bpp
wsdisplay0 at simplefb0 mux 1: console (std, vt100 emulation)
wsdisplay0: screen 1-5 added (std, vt100 emulation)
usb3 at ohci0: USB revision 1.0
uhub3 at usb3 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00
addr 1
usb4 at ohci1: USB revision 1.0
uhub4 at usb4 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00
addr 1
pci0 at dwpcie0
ppb0 at pci0 dev 0 function 0 "Rockchip RK3566" rev 0x00
pci1 at ppb0 bus 1
"Intel WiFi Link 1030" rev 0x1a at pci1 dev 0 function 0 not configured
pci2 at dwpcie1
ppb1 at pci2 dev 0 function 0 "Rockchip RK3566" rev 0x00
pci3 at ppb1 bus 1
rge0 at pci3 dev 0 function 0 "Realtek RTL8125" rev 0x05: msi, address
00:00:00:00:00:00
pci4 at dwpcie2
ppb2 at pci4 dev 0 function 0 "Rockchip RK3566" rev 0x00
pci5 at ppb2 bus 1
rge1 at pci5 dev 0 function 0 "Realtek RTL8125" rev 0x05: msi, address
00:00:00:00:00:00
scsibus1 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus1 targ 1 lun 0: <SD/MMC, NCard, 0010> removable
sd0: 14910MB, 512 bytes/sector, 30535680 sectors
sdmmc1: can't enable card
sdhc_sdclk_frequency_select: command in progress
umass0 at uhub0 port 2 configuration 1 interface 0 "USB SanDisk 3.2Gen1" rev
3.20/1.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus2 at umass0: 2 targets, initiator 0
sd1 at scsibus2 targ 1 lun 0: <USB, SanDisk 3.2Gen1, 1.00> removable
serial.0781558381075e2a041c
sd1: 29340MB, 512 bytes/sector, 60088320 sectors
uhidev0 at uhub4 port 1 configuration 1 interface 0 "Logitech USB Keyboard" rev
1.10/64.02 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 variable keys, 6 key codes
wskbd0 at ukbd0: console keyboard, using wsdisplay0
uhidev1 at uhub4 port 1 configuration 1 interface 1 "Logitech USB Keyboard" rev
1.10/64.02 addr 2
uhidev1: iclass 3/0, 5 report ids
ucc0 at uhidev1 reportid 1: 2 usages, 3 keys, enum
wskbd1 at ucc0 mux 1
wskbd1: connecting to wsdisplay0
uhid0 at uhidev1 reportid 2: input=1, output=0, feature=0
ucc1 at uhidev1 reportid 3: 21 usages, 14 keys, enum
wskbd2 at ucc1 mux 1
wskbd2: connecting to wsdisplay0
uhid1 at uhidev1 reportid 5: input=0, output=0, feature=5
vscsi0 at root
scsibus3 at vscsi0: 256 targets
softraid0 at root
scsibus4 at softraid0: 256 targets
root on sd1a (d9b3f31cd079d97e.a) swap on sd1b dump on sd1b
WARNING: bad clock chip time
WARNING: CHECK AND RESET THE DATE!
linkstar$
linkstar$
linkstar$
linkstar$ uname -a
OpenBSD linkstar.extrowerk.com 7.4 GENERIC.MP#40 arm64
linkstar$ doas pcidump -v
doas ([email protected]) password:
Domain /dev/pci0:
0:0:0: Rockchip RK3566
0x0000: Vendor ID: 1d87, Product ID: 3566
0x0004: Command: 0007, Status: 0010
0x0008: Class: 06 Bridge, Subclass: 04 PCI,
Interface: 00, Revision: 00
0x000c: BIST: 00, Header Type: 01, Latency Timer: 00,
Cache Line Size: 00
0x0010: BAR empty (00000000)
0x0014: BAR empty (00000000)
0x0018: Primary Bus: 0, Secondary Bus: 1, Subordinate Bus: 15,
Secondary Latency Timer: 00
0x001c: I/O Base: 01, I/O Limit: f1, Secondary Status: 0000
0x0020: Memory Base: f420, Memory Limit: f5f0
0x0024: Prefetch Memory Base: 4001, Prefetch Memory Limit: 7ff1
0x0028: Prefetch Memory Base Upper 32 Bits: 00000000
0x002c: Prefetch Memory Limit Upper 32 Bits: 00000000
0x0030: I/O Base Upper 16 Bits: f410, I/O Limit Upper 16 Bits: f41f
0x0038: Expansion ROM Base Address: 00000000
0x003c: Interrupt Pin: 01, Line: ff, Bridge Control: 0000
0x0040: Capability 0x01: Power Management
State: D0
0x0050: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: no
0x0070: Capability 0x10: PCI Express
Max Payload Size: 128 / 128 bytes
Max Read Request Size: 512 bytes
Link Speed: 2.5 / 8.0 GT/s
Link Width: x1 / x1
0x0100: Enhanced Capability 0x01: Advanced Error Reporting
0x0148: Enhanced Capability 0x19: Secondary PCIe Capability
0x0160: Enhanced Capability 0x1e: L1 PM
0x0170: Enhanced Capability 0x0b: Vendor-Specific
0x00b0: Capability 0x11: Extended Message Signalled Interrupts (MSI-X)
Enabled: no; table size 1 (BAR 0:0)
1:0:0: Intel WiFi Link 1030
0x0000: Vendor ID: 8086, Product ID: 008a
0x0004: Command: 0000, Status: 0010
0x0008: Class: 02 Network, Subclass: 80 Miscellaneous,
Interface: 00, Revision: 1a
0x000c: BIST: 00, Header Type: 00, Latency Timer: 00,
Cache Line Size: 00
0x0010: BAR mem 64bit addr: 0x0000000000000000/0x00002000
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 0000
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: 00 Min Gnt: 00 Max Lat: 00
0x00c8: Capability 0x01: Power Management
State: D0
0x00d0: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: no
0x00e0: Capability 0x10: PCI Express
Max Payload Size: 128 / 128 bytes
Max Read Request Size: 128 bytes
Link Speed: 2.5 / 2.5 GT/s
Link Width: x1 / x1
0x0100: Enhanced Capability 0x01: Advanced Error Reporting
0x0140: Enhanced Capability 0x03: Device Serial Number
Serial Number: 000000ffff000000
Domain /dev/pci1:
0:0:0: Rockchip RK3566
0x0000: Vendor ID: 1d87, Product ID: 3566
0x0004: Command: 0007, Status: 0010
0x0008: Class: 06 Bridge, Subclass: 04 PCI,
Interface: 00, Revision: 00
0x000c: BIST: 00, Header Type: 01, Latency Timer: 00,
Cache Line Size: 00
0x0010: BAR empty (00000000)
0x0014: BAR empty (00000000)
0x0018: Primary Bus: 0, Secondary Bus: 1, Subordinate Bus: 15,
Secondary Latency Timer: 00
0x001c: I/O Base: 01, I/O Limit: f1, Secondary Status: 0000
0x0020: Memory Base: f220, Memory Limit: f3f0
0x0024: Prefetch Memory Base: 4001, Prefetch Memory Limit: 7ff1
0x0028: Prefetch Memory Base Upper 32 Bits: 00000000
0x002c: Prefetch Memory Limit Upper 32 Bits: 00000000
0x0030: I/O Base Upper 16 Bits: f210, I/O Limit Upper 16 Bits: f21f
0x0038: Expansion ROM Base Address: 00000000
0x003c: Interrupt Pin: 01, Line: ff, Bridge Control: 0000
0x0040: Capability 0x01: Power Management
State: D0
0x0050: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: no
0x0070: Capability 0x10: PCI Express
Max Payload Size: 128 / 256 bytes
Max Read Request Size: 512 bytes
Link Speed: 2.5 / 8.0 GT/s
Link Width: x1 / x1
0x0100: Enhanced Capability 0x01: Advanced Error Reporting
0x0148: Enhanced Capability 0x19: Secondary PCIe Capability
0x0160: Enhanced Capability 0x1e: L1 PM
0x0170: Enhanced Capability 0x0b: Vendor-Specific
0x00b0: Capability 0x11: Extended Message Signalled Interrupts (MSI-X)
Enabled: no; table size 128 (BAR 4:131072)
1:0:0: Realtek RTL8125
0x0000: Vendor ID: 10ec, Product ID: 8125
0x0004: Command: 0006, Status: 0010
0x0008: Class: 02 Network, Subclass: 00 Ethernet,
Interface: 00, Revision: 05
0x000c: BIST: 00, Header Type: 00, Latency Timer: 00,
Cache Line Size: 00
0x0010: BAR io addr: 0x00000000/0x0100
0x0014: BAR empty (00000000)
0x0018: BAR mem 64bit addr: 0x00000000f2200000/0x00010000
0x0020: BAR mem 64bit addr: 0x0000000000000000/0x00004000
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 10ec Product ID: 8125
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: ff Min Gnt: 00 Max Lat: 00
0x0040: Capability 0x01: Power Management
State: D0
0x0050: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: yes
0x0070: Capability 0x10: PCI Express
Max Payload Size: 128 / 256 bytes
Max Read Request Size: 512 bytes
Link Speed: 2.5 / 5.0 GT/s
Link Width: x1 / x1
0x0100: Enhanced Capability 0x01: Advanced Error Reporting
0x0148: Enhanced Capability 0x02: Virtual Channel Capability
0x0168: Enhanced Capability 0x03: Device Serial Number
Serial Number: 0000000000000000
0x0178: Enhanced Capability 0x17: TPH Requester
0x0204: Enhanced Capability 0x18: Latency Tolerance Reporting
0x020c: Enhanced Capability 0x1e: L1 PM
0x021c: Enhanced Capability 0x0b: Vendor-Specific
0x00b0: Capability 0x11: Extended Message Signalled Interrupts (MSI-X)
Enabled: no; table size 32 (BAR 4:0)
0x00d0: Capability 0x03: Vital Product Data (VPD)
7f: [|vpd]
Domain /dev/pci2:
0:0:0: Rockchip RK3566
0x0000: Vendor ID: 1d87, Product ID: 3566
0x0004: Command: 0007, Status: 0010
0x0008: Class: 06 Bridge, Subclass: 04 PCI,
Interface: 00, Revision: 00
0x000c: BIST: 00, Header Type: 01, Latency Timer: 00,
Cache Line Size: 00
0x0010: BAR mem 64bit addr: 0x0000000000000000/0x40000000
0x0018: Primary Bus: 0, Secondary Bus: 1, Subordinate Bus: 15,
Secondary Latency Timer: 00
0x001c: I/O Base: 01, I/O Limit: f1, Secondary Status: 0000
0x0020: Memory Base: f020, Memory Limit: f1f0
0x0024: Prefetch Memory Base: 4001, Prefetch Memory Limit: 7ff1
0x0028: Prefetch Memory Base Upper 32 Bits: 00000000
0x002c: Prefetch Memory Limit Upper 32 Bits: 00000000
0x0030: I/O Base Upper 16 Bits: f010, I/O Limit Upper 16 Bits: f01f
0x0038: Expansion ROM Base Address: 00000000
0x003c: Interrupt Pin: 01, Line: ff, Bridge Control: 0000
0x0040: Capability 0x01: Power Management
State: D0
0x0050: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: no
0x0070: Capability 0x10: PCI Express
Max Payload Size: 128 / 256 bytes
Max Read Request Size: 512 bytes
Link Speed: 5.0 / 8.0 GT/s
Link Width: x1 / x2
0x0100: Enhanced Capability 0x01: Advanced Error Reporting
0x0148: Enhanced Capability 0x19: Secondary PCIe Capability
0x0160: Enhanced Capability 0x1e: L1 PM
0x01a0: Enhanced Capability 0x0b: Vendor-Specific
0x02a0: Enhanced Capability 0x0b: Vendor-Specific
0x00b0: Capability 0x11: Extended Message Signalled Interrupts (MSI-X)
Enabled: no; table size 128 (BAR 4:131072)
1:0:0: Realtek RTL8125
0x0000: Vendor ID: 10ec, Product ID: 8125
0x0004: Command: 0006, Status: 0010
0x0008: Class: 02 Network, Subclass: 00 Ethernet,
Interface: 00, Revision: 05
0x000c: BIST: 00, Header Type: 00, Latency Timer: 00,
Cache Line Size: 00
0x0010: BAR io addr: 0x00000000/0x0100
0x0014: BAR empty (00000000)
0x0018: BAR mem 64bit addr: 0x00000000f0200000/0x00010000
0x0020: BAR mem 64bit addr: 0x0000000000000000/0x00004000
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 10ec Product ID: 8125
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: ff Min Gnt: 00 Max Lat: 00
0x0040: Capability 0x01: Power Management
State: D0
0x0050: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: yes
0x0070: Capability 0x10: PCI Express
Max Payload Size: 128 / 256 bytes
Max Read Request Size: 512 bytes
Link Speed: 5.0 / 5.0 GT/s
Link Width: x1 / x1
0x0100: Enhanced Capability 0x01: Advanced Error Reporting
0x0148: Enhanced Capability 0x02: Virtual Channel Capability
0x0168: Enhanced Capability 0x03: Device Serial Number
Serial Number: 0000000000000000
0x0178: Enhanced Capability 0x17: TPH Requester
0x0204: Enhanced Capability 0x18: Latency Tolerance Reporting
0x020c: Enhanced Capability 0x1e: L1 PM
0x021c: Enhanced Capability 0x0b: Vendor-Specific
0x00b0: Capability 0x11: Extended Message Signalled Interrupts (MSI-X)
Enabled: no; table size 32 (BAR 4:0)
0x00d0: Capability 0x03: Vital Product Data (VPD)
7f: [|vpd]
linkstar$ ifconfig
lo0: flags=2008049<UP,LOOPBACK,RUNNING,MULTICAST,LRO> mtu 32768
index 6 priority 0 llprio 3
groups: lo
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x6
inet 127.0.0.1 netmask 0xff000000
dwqe0: flags=808843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,AUTOCONF4> mtu 1500
lladdr 3e:68:a7:8e:7e:25
index 1 priority 0 llprio 3
media: Ethernet autoselect (none)
status: no carrier
dwqe1: flags=808843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,AUTOCONF4> mtu 1500
lladdr 3e:68:a7:8e:7e:24
index 2 priority 0 llprio 3
media: Ethernet autoselect (none)
status: no carrier
rge0: flags=808843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,AUTOCONF4> mtu 1500
lladdr 3e:68:a7:8e:7e:23
index 3 priority 0 llprio 3
media: Ethernet autoselect
status: no carrier
rge1: flags=808843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,AUTOCONF4> mtu 1500
lladdr 3e:68:a7:8e:7e:22
index 4 priority 0 llprio 3
groups: egress
media: Ethernet autoselect (1000baseT full-duplex)
status: active
inet 192.168.1.181 netmask 0xffffff00 broadcast 192.168.1.255
enc0: flags=0<>
index 5 priority 0 llprio 3
groups: enc
status: active
pflog0: flags=141<UP,RUNNING,PROMISC> mtu 33136
index 7 priority 0 llprio 3
groups: pflog
--Z--
