Je viens de tenter le coup avec Knoppix;
ici aussi ça ne veut rien entendre, le stick est non partitionnable
selon fdisk qui dit être unable to open /dev/sdb
et cfdisk qui fais un fatal error.
Et si je prend l'installeur Etch, là ça me repropose en boucle à un
moment de Detech disk drives...
Il est donc impossible d'utiliser ce stick;
je vais le reporter au magasin.
Voici déjà une sortie dmesg sous Knoppix, qui ne plante pas la console
derrière /dev/scsi/host3/bus0/target0/lun0:
usb 3-1: new full speed USB device using uhci_hcd and address 2
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
Vendor: Model: USB DISK Pro Rev: PMAP
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sdb: 1965056 512-byte hdwr sectors (1006 MB)
sdb: Write Protect is off
sdb: Mode Sense: 23 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 1965056 512-byte hdwr sectors (1006 MB)
sdb: Write Protect is off
sdb: Mode Sense: 23 00 00 00
sdb: assuming drive cache: write through
sdb:<6>usb 3-1: reset full speed USB device using uhci_hcd and address 2
usb 3-1: device descriptor read/64, error -110
usb 3-1: device descriptor read/64, error -110
usb 3-1: reset full speed USB device using uhci_hcd and address 2
usb 3-1: device descriptor read/64, error -110
usb 3-1: device descriptor read/64, error -110
usb 3-1: reset full speed USB device using uhci_hcd and address 2
usb 3-1: device not accepting address 2, error -110
usb 3-1: reset full speed USB device using uhci_hcd and address 2
usb 3-1: device not accepting address 2, error -110
scsi: Device offlined - not ready after error recovery: host 3 channel 0 id 0
lun 0
usb 3-1: USB disconnect, address 2
SCSI error : <3 0 0 0> return code = 0x50000
end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
scsi3 (0:0): rejecting I/O to offline device
Buffer I/O error on device sdb, logical block 0
unable to read partition table
Attached scsi removable disk sdb at scsi3, channel 0, id 0, lun 0
usb-storage: device scan complete
usb 3-1: new full speed USB device using uhci_hcd and address 3
usb 3-1: device descriptor read/64, error -110
usb 3-1: device descriptor read/64, error -110
usb 3-1: new full speed USB device using uhci_hcd and address 4
usb 3-1: device descriptor read/64, error -110
usb 3-1: device descriptor read/64, error -110
usb 3-1: new full speed USB device using uhci_hcd and address 5
usb 3-1: device not accepting address 5, error -110
usb 3-1: new full speed USB device using uhci_hcd and address 6
usb 3-1: device not accepting address 6, error -110
Aldo.
_______________________________________________
Liste de diffusion CarrefourBLinuX
[email protected]
http://lists.freearchive.org/mailman/listinfo/carrefourblinux
Fiches EDU : http://blinuxwiki.pbwiki.com/FichesEdu
Signets : http://fr.groups.yahoo.com/group/carrefourblinux/links/
Archives : http://lists.freearchive.org/pipermail//carrefourblinux
Anciennes archives (Yahoogroupes) :
http://fr.groups.yahoo.com/group/carrefourblinux/messages
Rechercher : http://lists.freearchive.org/cgi-bin/search.cgi
Pour s'inscire par courriel :
'mailto:[EMAIL PROTECTED]'
Pour se desinscrire par courriel :
'mailto:[EMAIL PROTECTED]'
