Le 05/09/08, Aldo<[EMAIL PROTECTED]> a écrit :
> Essayes ceci:
> - insérer la clé D-link, puis taper: dmesg 'enter'
Voici le résultat :
Linux version 2.6.18-6-686 (Debian 2.6.18.dfsg.1-22)
([EMAIL PROTECTED]) (gcc version 4.1.2 20061115 (prerelease) (Debian
4.1.1-21)) #1 SMP Tue Jun 17 21:31:27 UTC 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000ffe0000 (usable)
BIOS-e820: 000000000ffe0000 - 000000000ffefc00 (ACPI data)
BIOS-e820: 000000000ffefc00 - 000000000fff0000 (ACPI NVS)
BIOS-e820: 000000000fff0000 - 000000000fff2000 (reserved)
BIOS-e820: 000000000fff2000 - 0000000010000000 (usable)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
256MB LOWMEM available.
On node 0 totalpages: 65536
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 61440 pages, LIFO batch:15
DMI 2.3 present.
ACPI: RSDP (v000 FUJ ) @ 0x000f64d0
ACPI: RSDT (v001 FUJ QUILT 0x01060000 FUJ 0x00001000) @ 0x0ffec74f
ACPI: FADT (v001 FUJ QUILT 0x01060000 FUJ 0x00001000) @ 0x0ffefb8c
ACPI: DSDT (v001 FUJ QUILT 0x01060000 MSFT 0x01000007) @ 0x00000000
ACPI: PM-Timer IO Port: 0xff08
Allocating PCI resources starting at 20000000 (gap: 10000000:eff00000)
Detected 497.572 MHz processor.
Built 1 zonelists. Total pages: 65536
Kernel command line: root=/dev/hda1 ro
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (01209000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 251828k/262144k available (1541k kernel code, 9672k reserved,
580k data, 196k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 996.06 BogoMIPS (lpj=1992123)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040
00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
ACPI: Core revision 20060707
ACPI: setting ELCR to 0200 (from 8200)
CPU0: Intel Celeron (Coppermine) stepping 06
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 4736k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd9ce, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI quirk: region ff00-ff3f claimed by PIIX4 ACPI
PCI quirk: region ff80-ff8f claimed by PIIX4 SMB
PIIX4 devres C PIO at fd60-fd67
PIIX4 devres G PIO at 0118-011f
PCI: Firmware left 0000:00:12.0 e100 interrupts enabled, disabling
Boot video device is 0000:00:14.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC] (gpe 44) interrupt mode.
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 *9 10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *9 10 11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 *15)
ACPI: Power Resource [USBP] (on)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:01: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:01: ioport range 0xff00-0xff3f could not be reserved
pnp: 00:01: ioport range 0xf800-0xf87f has been reserved
PCI: Bus 1, cardbus bridge: 0000:00:13.0
IO window: 00001c00-00001cff
IO window: 00002800-000028ff
PREFETCH window: 20000000-21ffffff
MEM window: 22000000-23ffffff
PCI: Bus 5, cardbus bridge: 0000:00:13.1
IO window: 00002c00-00002cff
IO window: 00003000-000030ff
PREFETCH window: 24000000-25ffffff
MEM window: 26000000-27ffffff
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LNKA] -> GSI 9 (level,
low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:13.0 to 64
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 9
ACPI: PCI Interrupt 0000:00:13.1[B] -> Link [LNKB] -> GSI 9 (level,
low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:13.1 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1220634558.316:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS3 at I/O 0x2e8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PCI: Enabling device 0000:00:00.2 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:00.2[B] -> Link [LNKB] -> GSI 9 (level,
low) -> IRQ 9
ACPI: PCI interrupt for device 0000:00:00.2 disabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI No-Shortcut mode
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 196k freed
Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 15
PCI: setting IRQ 15 as level-triggered
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 15 (level,
low) -> IRQ 15
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 15, io base 0x00001480
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 9
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKC] -> GSI 9 (level,
low) -> IRQ 9
e100: eth0: e100_probe: addr 0xfc020000, irq 9, MAC addr 00:E0:00:1A:6B:2C
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 0000:00:07.1
PIIX4: chipset revision 0
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x14a0-0x14a7, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
Time: acpi_pm clocksource has been installed.
hda: TOSHIBA MK2018GAS, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 39070080 sectors (20003 MB), CHS=38760/16/63, UDMA(33)
hda: cache flushes supported
hda: hda1 hda2 hda3 < hda5 >
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Intel 810 + AC97 Audio, version 1.01, 21:51:29 Jun 17 2008
ACPI: PCI Interrupt 0000:00:00.1[B] -> Link [LNKB] -> GSI 9 (level,
low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:00.1 to 64
i810: Intel 440MX found at IO 0x1400 and 0x1000, MEM 0x0000 and 0x0000, IRQ 9
i810_audio: Audio Controller supports 2 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
ac97_codec: AC97 Audio codec, id: 0x8384:0x7609 (SigmaTel STAC9721/23)
i810_audio: only 48Khz playback available.
i810_audio: AC'97 codec 0 supports AMAP, total channels = 2
PCI: Enabling device 0000:00:00.2 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:00.2[B] -> Link [LNKB] -> GSI 9 (level,
low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:00.2 to 64
Yenta: CardBus bridge found at 0000:00:13.0 [10cf:10e6]
Yenta O2: res at 0x94/0xD4: ea/00
Yenta O2: enabling read prefetch/write burst
Yenta: ISA IRQ mask 0x0cb8, PCI irq 9
Socket status: 30000006
Yenta: CardBus bridge found at 0000:00:13.1 [10cf:10e6]
Yenta: ISA IRQ mask 0x0cb8, PCI irq 9
Socket status: 30000006
input: PC Speaker as /class/input/input1
piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
Real Time Clock Driver v1.12ac
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
irda_init()
NET: Registered protocol family 23
input: LBPS/2 Fujitsu Lifebook TouchScreen as /class/input/input2
found SMC SuperIO Chip (devid=0x28 rev=01 base=0x03f0): FDC37N769
smsc_superio_flat(): fir: 0x118, sir: 0x2e8, dma: 03, irq: 3, mode: 0x0e
smsc_ircc_present: can't get sir_base of 0x2e8
ts: Compaq touchscreen protocol output
cs: IO port probe 0x100-0x3af: excluding 0x118-0x11f
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0x100-0x3af: excluding 0x118-0x11f
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
Adding 498004k swap on /dev/hda2. Priority:-1 extents:1 across:498004k
EXT3 FS on hda1, internal journal
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: [EMAIL PROTECTED]
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ACPI: Battery Slot [CMB1] (battery present)
ACPI: AC Adapter [AC] (on-line)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Lid Switch [LID]
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
usb 1-1: new full speed USB device using uhci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
usb 1-1: USB disconnect, address 2
usb 1-1: new full speed USB device using uhci_hcd and address 3
usb 1-1: configuration #1 chosen from 1 choice
usb 1-1: USB disconnect, address 3
usb 1-1: new full speed USB device using uhci_hcd and address 4
usb 1-1: configuration #1 chosen from 1 choice
> - faire ensuite: lsusb 'enter' pour qu'il t'affiche tout qui est sur l'USB
Bus 001 Device 004: ID 07d1:3c03 D-Link System
Bus 001 Device 001: ID 0000:0000
> - puis: dpkg -l |grep -i usb 'enter' pour que ça nous montre quels packs
> USB
> sont déjà sur ta Debian
Aucun paquet ne correspond à /grep.
Aucun paquet ne correspond à -i.
Aucun paquet ne correspond à usb.
Cristian
_______________________________________________
Liste de diffusion CarrefourBLinuX
[email protected]
http://lists.freearchive.org/mailman/listinfo/carrefourblinux
Pour s'inscrire par courriel :
'mailto:[EMAIL PROTECTED]'
Pour se retirer de la liste par courriel :
'mailto:[EMAIL PROTECTED]'
Archives : http://lists.freearchive.org/pipermail//carrefourblinux
Anciennes archives (Yahoogroupes) :
http://fr.groups.yahoo.com/group/carrefourblinux/messages
Rechercher : http://lists.freearchive.org/cgi-bin/search.cgi
Signets : http://fr.groups.yahoo.com/group/carrefourblinux/links/
Fiches EDU : http://blinuxwiki.pbwiki.com/FichesEdu
