Phil and all,
This is turning into a novel; I'll try to be brief.
My meter came with a glued down paper meter face, which I interpreted
from my experience from buying GPSs and electrical multimeters (some
Chinese, by the way) etc., as being the temporary marketing
presentation that makes the meter look like what it would in use.
These latter are, of course, intended to be peeled away prior to use.
So I peeled away the paper, only the third part of which came off.
Damned if it wasn't intended to be a permanent part of the meter!
I suspect the Harbor Freight comment that there might be quick model
changes refers to this situation. They may be going to look a little
less naive in future models. Other than this, I see not much need for
such changes.
RudyB
Rudolph S. Behar wrote:
Phil,
It's item #93300
RudyB
Phil Agur wrote:
Rudy,
Harbor may substitute a different make and model in the future, which one do
you have?
Phil Agur s/v Wing Tip
Commodore, Call Sign WCW3485
IC27/270A MMSI 366901790
www.catalina27.org Vessel Doc# 1039809
-----Original Message-----
From: [email protected]
[mailto:[email protected]] On Behalf Of Rudolph S. Behar
Sent: Saturday, January 14, 2006 6:47 PM
To: [email protected]
Subject: Re: catalina27-talk: Harbor Freight Search Result Page
All,
I finally have given the meter a good try out and believe that the
Chinese must have copied the higher end meter, since the one I have
seems to work swell.
Some readings, for expectations.
Piano bench 6% moisture
Oak diniing room table: 6%
Kitchen cutting board: 12%
My hand: 40+ % (the literature suggests that this is near the top of the
meteer's range.)
Now the interesting ones:
Companionway boards: 12% (teak, and rained on yeasterday)
Sliding salon top: 6%
Cockpit floor: 6%
Six inches aft of the stem fitting: 7% ( I had rebedded the stem fitting
1 1/2 years ago)
1 1/2 foot aft of the stem fitting 16%
5" port and starboard of the mast step: 17%
These last two are right in line with the figures give me by my
surveyor, and I believe indicate a need for remedial action.
In all, and politics aside, I feel I can recommend the $150 meter. and
Harbor freight has a responsive return policy.
Operation is baby simple; battery is the common 9 volt battery, as used
in most smoke alarms.
Google Harbor Freight; search: moisture meter.
I'd be glad to set the meter to any boat reasonably near to Columbia or
Pasadena, MD
Rudy B.
Phoenix, #2237
Pasadena. MD
Rudolph S. Behar wrote:
Doug,
See my email to to Dave Breski for my situation with the meter. So
far I'm in the testing stage, or rather in the non-testing stage
because of the weather.
For me absolute accuracy is not all that important: I'm looking for
relative accuracy, to locate the wetter spots. I'll use the sliding
hatch-cover as a reference: I believe it is quite dry inside. The
four sensitivites may be useful, but they don't change things much:
At the lowest sensitivity, my oak dining room table read 6%, at max
sensitivity, it reads14%. Dave may very well be right about my meter,
which is definitely low-end.
I'm planning to try out the meter on the boat this weekend. Will
rreport.
Rudy
Doug Plotner wrote:
Rudy,
I didn't have luck with your link, but I did go onto
www.harborfreight.com, did a keyword search for "moisture" and found
the item I think you're talking about. The link I copied for it is:
http://www.harborfreight.com/cpi/ctaf/Displayitem.taf?itemnumber=93300
I noticed the description indicates that it has four scales for
various types of wood. Do you have any feel for what it's accuracy
might be for fiberglass, or for balsa sandwiched in fiberglass?
Thanks,
Doug Plotner
#6494 Dawg Daze
-----Original Message-----
From: "Rudolph S. Behar" <[EMAIL PROTECTED]>
Sent: Dec 13, 2005 8:47 AM
To: [email protected]
Subject: catalina27-talk: Harbor Freight Search Result Page
Hello,
For those who were interested in the non-contact ("non-destructive")
moisture meter from Harbor Freight, once again I think I've figured
out how to send a link. But it's true I've though that two other
times without being able to do so.
Herre's the current effort.
Rudy B.
Phoenix, #2237
Pasadena, MD
http://order.harborfreight.com/EasyAsk/harborfreight/results.jsp
|
