Rahul, the frame-relay switch configuration goes right into the .net file at the end. Here's a paste of my .net file to help you out. The frame switch is automatically loaded when you run Dynamips. Sounds like you're doing IE WB, so you'll need this below. You should be able to DL the complete .net file from IE's website when you login into the members section and goto Dynamips.
[[FRSW FRSW]] # R1 to FRSW 1:102 = 2:201 1:103 = 3:301 1:113 = 13:311 1:104 = 4:401 1:105 = 5:501 # R2 to FRSW 2:203 = 3:302 2:213 = 13:312 2:204 = 4:402 2:205 = 5:502 # R3 to FRSW 3:304 = 4:403 3:305 = 5:503 13:314 = 4:413 13:315 = 5:513 # R4 to FRSW 4:405 = 5:504 # R6 to FRSW 6:51 = 21:51 6:100 = 21:100 6:101 = 21:101 6:201 = 21:201 6:301 = 21:301 6:401 = 21:401 HTH, Dale On Wed, May 14, 2008 at 12:26 AM, rahul agarwal < [EMAIL PROTECTED]> wrote: > > Hi All, > > I am doing IEWB-RS-DYN Lab 1 currently in that i am facing problem between > the connection of R4 s1/0 and R5 s1/0. > > I can see the problem is the LMI packet are not reciving at there serial > interfaces see the sh frame-realy lmi of R4. > Same thing is in R5. > > Any suggestion to put the tunnel up. > > R4 config > ----------------------------------------------------- > interface Serial1/0 > ip address 183.1.0.4 255.255.255.0 > encapsulation frame-relay > serial restart-delay 0 > no dce-terminal-timing-enable > frame-relay map ip 183.1.0.5 405 > frame-relay lmi-type ansi > end > ------------------------------------------------------- > Rack1R4#sh int s1/0 > Serial1/0 is up, line protocol is down > Hardware is M4T > Internet address is 183.1.0.4/24 > MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, > reliability 255/255, txload 1/255, rxload 1/255 > Encapsulation FRAME-RELAY, crc 16, loopback not set > Keepalive set (10 sec) > Restart-Delay is 0 secs > LMI enq sent 50, LMI stat recvd 0, LMI upd recvd 0, DTE LMI down > LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0 > LMI DLCI 0 LMI type is ANSI Annex D frame relay DTE > FR SVC disabled, LAPF state down > Broadcast queue 0/64, broadcasts sent/dropped 0/0, interface broadcasts 0 > Last input never, output 00:00:06, output hang never > Last clearing of "show interface" counters 00:08:25 > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 > Queueing strategy: weighted fair > Output queue: 0/1000/64/0 (size/max total/threshold/drops) > Conversations 0/1/256 (active/max active/max total) > Reserved Conversations 0/0 (allocated/max allocated) > Available Bandwidth 1158 kilobits/sec > 5 minute input rate 0 bits/sec, 0 packets/sec > 5 minute output rate 0 bits/sec, 0 packets/sec > 0 packets input, 0 bytes, 0 no buffer > Received 0 broadcasts, 0 runts, 0 giants, 0 throttles > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort > 51 packets output, 714 bytes, 0 underruns > 0 output errors, 0 collisions, 1 interface resets > 0 output buffer failures, 0 output buffers swapped out > 1 carrier transitions DCD=up DSR=up DTR=up RTS=up CTS=up > > -------------------------------------------------------------------------------------- > > Rack1R4#sh fram > Rack1R4#sh frame-relay lmi > LMI Statistics for interface Serial1/0 (Frame Relay DTE) LMI TYPE = ANSI > Invalid Unnumbered info 0 Invalid Prot Disc 0 > Invalid dummy Call Ref 0 Invalid Msg Type 0 > Invalid Status Message 0 Invalid Lock Shift 0 > Invalid Information ID 0 Invalid Report IE Len 0 > Invalid Report Request 0 Invalid Keep IE Len 0 > Num Status Enq. Sent 389 Num Status msgs Rcvd 0 > Num Update Status Rcvd 0 Num Status Timeouts 388 > Last Full Status Req 00:00:05 Last Full Status Rcvd never > --------------------------------------------------------------- > R5 config > ======== > interface Serial1/0 > ip address 183.1.0.5 255.255.255.0 > encapsulation frame-relay > serial restart-delay 0 > no dce-terminal-timing-enable > fair-queue > frame-relay map ip 183.1.0.4 504 > frame-relay lmi-type ansi > end > > ----------------------------------------------------------------------------- > > Rack1R5#sh interfaces s1/0 > Serial1/0 is up, line protocol is down > Hardware is M4T > Internet address is 183.1.0.5/24 > MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, > reliability 255/255, txload 1/255, rxload 1/255 > Encapsulation FRAME-RELAY, crc 16, loopback not set > Keepalive set (10 sec) > Restart-Delay is 0 secs > LMI enq sent 6, LMI stat recvd 0, LMI upd recvd 0, DTE LMI down > LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0 > LMI DLCI 0 LMI type is ANSI Annex D frame relay DTE > FR SVC disabled, LAPF state down > Broadcast queue 0/64, broadcasts sent/dropped 0/0, interface broadcasts 0 > Last input never, output 00:00:00, output hang never > Last clearing of "show interface" counters 00:11:49 > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 > Queueing strategy: weighted fair > Output queue: 0/1000/64/0 (size/max total/threshold/drops) > Conversations 0/1/256 (active/max active/max total) > Reserved Conversations 0/0 (allocated/max allocated) > Available Bandwidth 1158 kilobits/sec > 5 minute input rate 0 bits/sec, 0 packets/sec > 5 minute output rate 0 bits/sec, 0 packets/sec > 0 packets input, 0 bytes, 0 no buffer > Received 0 broadcasts, 0 runts, 0 giants, 0 throttles > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort > 6 packets output, 84 bytes, 0 underruns > 0 output errors, 0 collisions, 4 interface resets > 0 output buffer failures, 0 output buffers swapped out > 1 carrier transitions DCD=up DSR=up DTR=up RTS=up CTS=up > > -------------------------------------------------------------------------------------------------- > > > > ------------------------------ > Unlimited freedom, unlimited storage. Get it > now<http://in.rd.yahoo.com/tagline_mail_2/*http://help.yahoo.com/l/in/yahoo/mail/yahoomail/tools/tools-08.html/> >
