hi guys, I think I have found the answer.That is a bug.
he dynamips forum mentioned that there is bug in 16 port module. honestly this is not a proper L3 switches. Insteadod using routed port I have used vlan interface.It is working fine.. FYI On 2/16/10, Mustafa Yadav <[email protected]> wrote: > hi Guys > > I can not solve a problem.The topology like this.A routed port in sw1 > (in f1/8)-----sw2 f1/(access vlan107)----trunk---sw3(f 1/15 access > vlan 107)------sw4 f1/15 routed port. > > I have done very basic config of this and I was able to ping between > sw1 ip address and sw4 ip address in the routed ports.This 4 switches > have more than one connection between each other. > When I installed attached configs my pc cpu is going very high.I did > try to perform a good troobleshooting but I have lost.I think thr arp > packets at first is going a loop and kill s my pc. > > Please help. > Swich connection as shown below. > > > [[ROUTER SW1]] > model = 3725 > console = 2007 > #cnfg=C:\Documents and Settings\\Desktop\1\Initial > Configs\Rack1\sw1.txt > slot1 = NM-16ESW > f1/1 = R1 f0/0 > f1/3 = R3 f0/0 > f1/5 = R5 f0/0 > f1/7 = SW2 f1/7 > f1/8 = SW2 f1/8 > f1/9 = SW2 f1/9 > f1/10 = SW3 f1/7 > f1/11 = SW3 f1/8 > f1/12 = SW3 f1/9 > f1/13 = SW4 f1/7 > f1/14 = SW4 f1/8 > f1/15 = SW4 f1/9 > x = -602.0 > y = -344.0 > [[ROUTER SW2]] > model = 3725 > console = 2008 > #cnfg=C:\Documents and Settings\Desktop\1\Initial > Configs\Rack1\sw2.txt > slot1 = NM-16ESW > f1/0 = BB2 f0/0 > f1/2 = R2 f0/0 > f1/4 = R4 f0/0 > f1/6 = R6 f0/0 > f1/7 = SW1 f1/7 > f1/8 = SW1 f1/8 > f1/9 = SW1 f1/9 > f1/10 = SW3 f1/10 > f1/11 = SW3 f1/11 > f1/12 = SW3 f1/12 > f1/13 = SW4 f1/10 > f1/14 = SW4 f1/11 > f1/15 = SW4 f1/12 > x = -616.0 > y = -186.0 > [[ROUTER SW3]] > model = 3725 > console = 2009 > #cnfg=C:\Documents and Settings\Desktop\1\Initial > Configs\Rack1\sw3.txt > slot1 = NM-16ESW > f1/0 = BB3 f0/0 > f1/3 = R3 f0/1 > f1/5 = R5 f0/1 > f1/7 = SW1 f1/10 > f1/8 = SW1 f1/11 > f1/9 = SW1 f1/12 > f1/10 = SW2 f1/10 > f1/11 = SW2 f1/11 > f1/12 = SW2 f1/12 > f1/13 = SW4 f1/13 > f1/14 = SW4 f1/14 > f1/15 = SW4 f1/15 > x = -294.0 > y = -337.0 > [[ROUTER SW4]] > model = 3725 > console = 2010 > #cnfg=C:\Documents and SettingsDesktop\1\Initial > Configs\Rack1\sw4.txt > slot1 = NM-16ESW > f1/4 = R4 f0/1 > f1/6 = R6 f0/1 > f1/7 = SW1 f1/13 > f1/8 = SW1 f1/14 > f1/9 = SW1 f1/15 > f1/10 = SW2 f1/13 > f1/11 = SW2 f1/14 > f1/12 = SW2 f1/15 > f1/13 = SW3 f1/13 > f1/14 = SW3 f1/14 > f1/15 = SW3 f1/15 > x = -296.0 > y = -179.0 > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
