Sorry, missed your second email. I don't see anything on the connectivity diagram that mention Gig 0/0 on R2.
On Mon, Mar 22, 2010 at 4:39 PM, FoosYou <[email protected]> wrote: > Unless I'm missing something it's not coming up. > > R2#sh run int g0/0 > Building configuration... > > Current configuration : 93 bytes > ! > interface GigabitEthernet0/0 > no ip address > duplex auto > speed auto > media-type rj45 > end > > R2#sh int g0/0 > GigabitEthernet0/0 is up, line protocol is down > Hardware is BCM1125 Internal MAC, address is 0011.9368.a0d0 (bia > 0011.9368.a0d0) > MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec, > reliability 255/255, txload 1/255, rxload 1/255 > Encapsulation ARPA, loopback not set > Keepalive set (10 sec) > Unknown duplex, Unknown Speed, media type is RJ45 > output flow-control is XON, input flow-control is XON > ARP type: ARPA, ARP Timeout 04:00:00 > Last input never, output never, output hang never > Last clearing of "show interface" counters never > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 > Queueing strategy: fifo > Output queue: 0/40 (size/max) > 5 minute input rate 0 bits/sec, 0 packets/sec > 5 minute output rate 0 bits/sec, 0 packets/sec > 0 packets input, 0 bytes, 0 no buffer > Received 0 broadcasts, 0 runts, 0 giants, 0 throttles > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored > 0 watchdog, 0 multicast, 0 pause input > 0 input packets with dribble condition detected > 0 packets output, 0 bytes, 0 underruns > > Cat1(config-if)#do sh run int g0/2 > Building configuration... > > Current configuration : 71 bytes > ! > interface GigabitEthernet0/2 > switchport mode dynamic desirable > end > > Cat1(config-if)#do sh int g0/2 > GigabitEthernet0/2 is down, line protocol is down (notconnect) > Hardware is Gigabit Ethernet, address is 0012.01b0.f11a (bia > 0012.01b0.f11a) > MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, > reliability 255/255, txload 1/255, rxload 1/255 > Encapsulation ARPA, loopback not set > Keepalive not set > Auto-duplex, Auto-speed, link type is auto, media type is 1000BaseSX > input flow-control is off, output flow-control is desired > ARP type: ARPA, ARP Timeout 04:00:00 > Last input never, output never, output hang never > Last clearing of "show interface" counters never > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 > Queueing strategy: fifo > Output queue: 0/40 (size/max) > 5 minute input rate 0 bits/sec, 0 packets/sec > 5 minute output rate 0 bits/sec, 0 packets/sec > 0 packets input, 0 bytes, 0 no buffer > Received 0 broadcasts (0 multicasts) > 0 runts, 0 giants, 0 throttles > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored > 0 watchdog, 0 multicast, 0 pause input > 0 input packets with dribble condition detected > 0 packets output, 0 bytes, 0 underruns > 0 output errors, 0 collisions, 1 interface resets > 0 babbles, 0 late collision, 0 deferred > 0 lost carrier, 0 no carrier, 0 PAUSE output > 0 output buffer failures, 0 output buffers swapped out > > > On Mon, Mar 22, 2010 at 4:29 PM, Marko Milivojevic <[email protected]>wrote: > >> Ah, sorry. We updated Volume 2. Still, Volume 1 is correct. Please >> consult the general connectivity diagram in the WB - it's all there. >> >> -- >> Marko Milivojevic - CCIE #18427 >> Senior Technical Instructor - IPexpert >> >> YES! We include 400 hours of REAL rack >> time with our Blended Learning Solution! >> >> Mailto: [email protected] >> Telephone: +1.810.326.1444 >> Fax: +1.810.454.0130 >> Web: http://www.ipexpert.com/ >> >> On Mon, Mar 22, 2010 at 20:21, Marko Milivojevic <[email protected]> >> wrote: >> > Hello, >> > >> > We have JUST uploaded revised documents. Please, get the updated >> documents. >> > >> > Gi0/0 on R2 is connected to Cat1 Gi0/2. >> > >> > -- >> > Marko Milivojevic - CCIE #18427 >> > Senior Technical Instructor - IPexpert >> > >> > YES! We include 400 hours of REAL rack >> > time with our Blended Learning Solution! >> > >> > Mailto: [email protected] >> > Telephone: +1.810.326.1444 >> > Fax: +1.810.454.0130 >> > Web: http://www.ipexpert.com/ >> > >> > On Mon, Mar 22, 2010 at 20:17, FoosYou <[email protected]> wrote: >> >> Just getting started with the IPX Vol1 Lab1 and I'm not sure if this is >> a >> >> typo or I'm missing something. The VLAN/router interface table wants >> R2's >> >> Gig0/0 interface put into VLAN 12. I'm not seeing Gig 0/0 on R2 >> connected to >> >> anything based on the diagrams or via CDP with the interface enabled. >> >> >> >> Thanks! >> >> Jay >> >> >> >> _______________________________________________ >> >> For more information regarding industry leading CCIE Lab training, >> please >> >> visit www.ipexpert.com >> >> >> >> >> > >> > >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
