I am sorry, the task is 6.7 on LAB-6. On Thu, Sep 2, 2010 at 2:18 AM, Amer Mustafa <[email protected]> wrote:
> i have mentioned LAB-6 task 6.2. > > > > On Thu, Sep 2, 2010 at 2:04 AM, Jason Maynard <[email protected]>wrote: > >> I did not look at the lab – I will have a look, which volume? >> >> >> >> *From:* Amer Mustafa [mailto:[email protected]] >> *Sent:* September-01-10 7:01 PM >> >> *To:* Jason Maynard >> *Cc:* [email protected] >> *Subject:* Re: [OSL | CCIE_RS] Workbook 1 , LAB6 (Frame-Relay). >> >> >> >> I need to work on this more until i am confident. >> >> >> >> now see this, on task 6.2 (LAB6-Frame-Relay) : >> >> >> >> The only configuration the workbook recommends is : >> >> >> >> ================= >> >> on R6 : >> >> inter ser 0/1/0 >> >> encap fram >> >> ip add 150.100.100.6 255.255.255.0 >> >> ================== >> >> and then workbook does : show fram map and it finds 150.100.100.2 with >> DLCI 612. >> >> >> >> *I didnt find 150.100.100.2 in my show fram map command, i only found >> 150.100.24.4 ( why , and from where 150.100.24.4 is coming?).* >> >> >> >> i had to map ip 150.100.100.2 602 to make it run: >> >> >> >> *R6(config)#do show run | s Serial0/1/0** >> interface Serial0/1/0 >> ip address 150.100.100.6 255.255.255.0 >> encapsulation frame-relay >> frame-relay map ip 150.100.100.2 602 broadcast* >> >> >> >> R6#ping 150.100.100.2 >> >> Type escape sequence to abort. >> Sending 5, 100-byte ICMP Echos to 150.100.100.2, timeout is 2 seconds: >> !!!!! >> Success rate is 100 percent (5/5), round-trip min/avg/max = 16/16/20 ms >> >> On Thu, Sep 2, 2010 at 1:51 AM, Jason Maynard <[email protected]> >> wrote: >> >> You can always use inverse-arp to determine what DLCIs are available. Then >> do your configurations >> >> >> >> >> >> >> >> *From:* Amer Mustafa [mailto:[email protected]] >> *Sent:* September-01-10 6:42 PM >> >> >> *To:* Jason Maynard >> *Cc:* [email protected] >> *Subject:* Re: [OSL | CCIE_RS] Workbook 1 , LAB6 (Frame-Relay). >> >> >> >> Good. but why we have assigned " frame interface-dlci 214" >> >> >> >> from where we get this "214" since we are not running any inve arp and our >> show fram mapp commands doesnt show 214. >> >> On Thu, Sep 2, 2010 at 1:38 AM, Jason Maynard <[email protected]> >> wrote: >> >> Your problem was that you learned all the DLCI by inverse arp which >> assigned them to the physical interface. >> >> >> >> Most likely you configured the interface while it was up and before you >> could turn off inverse arp and therefore learned all the DLCI’s that were >> available. >> >> >> >> If you would have shut the physical interface then configured >> encapsulation and no frame-relay inverse-arp plus all other configuration >> and then brought up the interface you would not have a problem. >> >> >> >> >> >> *From:* Amer Mustafa [mailto:[email protected]] >> *Sent:* September-01-10 6:33 PM >> >> >> *To:* Jason Maynard >> *Cc:* [email protected] >> *Subject:* Re: [OSL | CCIE_RS] Workbook 1 , LAB6 (Frame-Relay). >> >> >> >> jason, >> >> >> >> Thanks alot, its working, but can you explain one point to me !? >> >> >> >> how and why we have decided to 214 on R2 !? >> >> >> >> if you remove the config to the default, and then configure one by one, >> you will endup having the same error, and when do show fram map you will not >> find any mappings for Serial0/1/0.1. >> >> >> >> the only mapping avilable is 150.100.24.4 ! >> >> >> >> Please advise. >> >> On Thu, Sep 2, 2010 at 1:23 AM, Amer Mustafa <[email protected]> >> wrote: >> >> Yup, its working but kinda confusing : >> >> >> >> >> >> on R2 : >> >> >> >> R2(config)#do show fram map >> >> >> Serial0/1/0 (up): ip 150.100.100.5 dlci 205(0xCD,0x30D0), static, >> broadcast, >> CISCO, status defined, inactive >> Serial0/1/0 (up): ip 150.100.100.2 dlci 205(0xCD,0x30D0), static, >> CISCO, status defined, inactive >> Serial0/1/0 (up): ip 150.100.100.6 dlci 206(0xCE,0x30E0), static, >> broadcast, >> CISCO, status defined, inactive >> >> Serial0/1/0.1 (up): point-to-point dlci, dlci 214(0xD6,0x3460), broadcast >> status defined, active >> Serial0/1/0 (up): ip 150.100.24.4 dlci *224** *(0xE0,0x3800), dynamic, >> broadcast,, status defined, active >> R2(config)# >> >> >> >> *R2#sh run | s Serial0/1/0 * >> >> * >> interface Serial0/1/0 >> description Frame Relay Links >> ip address 150.100.100.2 255.255.255.0 >> encapsulation frame-relay* >> >> * frame-relay map ip 150.100.100.5 205 broadcast * >> >> * >> frame-relay map ip 150.100.100.6 206 broadcast* >> >> * frame-relay map ip 150.100.100.2 205 * >> >> * >> no frame-relay inverse-arp >> interface Serial0/1/0.1 point-to-point >> ip address 150.100.24.2 255.255.255.0* >> >> * frame-relay interface-dlci 214 ** >> R2#* >> >> >> >> *on R4 : * >> >> *R4#show run | s Serial0/0/0 >> interface Serial0/0/0 >> ip address 150.100.24.4 255.255.255.0 >> encapsulation frame-relay* >> >> * frame-relay interface-dlci 412* >> >> *R4#show fram map** >> Serial0/0/0 (up): ip 150.100.100.2 dlci 402(0x192,0x6420), dynamic, >> broadcast,, status defined, active >> Serial0/0/0 (up): ip 150.100.24.2 dlci 412(0x19C,0x64C0), dynamic, >> broadcast,, status defined, active >> R4#* >> >> >> >> --- >> >> >> >> R4#ping 150.100.24.2 >> >> Type escape sequence to abort. >> Sending 5, 100-byte ICMP Echos to 150.100.24.2, timeout is 2 seconds: >> !!!!! >> >> Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms >> R4# >> >> On Thu, Sep 2, 2010 at 1:10 AM, Jason Maynard <[email protected]> >> wrote: >> >> You have your answer, the dlci is assigned to the wrong interface >> >> >> >> Copy and paste this – I know others shut the interface then make changes >> but I find it quicker to copy then default then paster >> >> >> >> *default inter serial 0/1/0* >> >> *interface Serial0/1/0** >> description Frame Relay Links >> ip address 150.100.100.2 255.255.255.0 >> encapsulation frame-relay >> frame-relay map ip 150.100.100.2 205 >> frame-relay map ip 150.100.100.6 206 broadcast >> frame-relay map ip 150.100.100.5 205 broadcast >> no frame-relay inverse-arp >> interface Serial0/1/0.1 point-to-point >> ip address 150.100.24.2 255.255.255.0* >> >> * no frame-relay inverse-arp* >> >> * frame-relay interface-dlci 214* >> >> >> >> >> >> *From:* Amer Mustafa [mailto:[email protected]] >> *Sent:* September-01-10 6:06 PM >> >> >> *To:* Jason Maynard >> *Cc:* [email protected] >> *Subject:* Re: [OSL | CCIE_RS] Workbook 1 , LAB6 (Frame-Relay). >> >> >> >> i have tried this even before i send to you : >> >> >> >> R2(config-subif)#do show fram map >> Serial0/1/0 (up): ip 150.100.100.2 dlci 205(0xCD,0x30D0), static, >> CISCO, status defined, inactive >> Serial0/1/0 (up): ip 150.100.100.5 dlci 205(0xCD,0x30D0), static, >> broadcast, >> CISCO, status defined, inactive >> Serial0/1/0 (up): ip 150.100.100.6 dlci 206(0xCE,0x30E0), static, >> broadcast, >> CISCO, status defined, inactive >> Serial0/1/0 (up): ip 150.100.24.4 dlci 214(0xD6,0x3460), dynamic, >> broadcast,, status defined, active >> R2(config-subif)#fram >> R2(config-subif)#frame-relay inter >> R2(config-subif)#frame-relay interface-dlci 214 ? >> cisco Use CISCO Encapsulation >> ietf Use RFC1490/RFC2427 Encapsulation >> ppp Use RFC1973 Encapsulation to support PPP over FR >> protocol Optional protocol information for remote end >> <cr> >> >> R2(config-subif)#frame-relay interface-dlci 214 >> *%PVC already assigned to interface Serial0/1/0* >> R2(config-subif)# >> >> On Thu, Sep 2, 2010 at 12:59 AM, Jason Maynard <[email protected]> >> wrote: >> >> *R2(config)#do sh run | s Serial0/1/0** >> interface Serial0/1/0 >> description Frame Relay Links >> ip address 150.100.100.2 255.255.255.0 >> encapsulation frame-relay >> frame-relay map ip 150.100.100.2 205 >> frame-relay map ip 150.100.100.6 206 broadcast >> frame-relay map ip 150.100.100.5 205 broadcast >> no frame-relay inverse-arp >> interface Serial0/1/0.1 point-to-point >> ip address 150.100.24.2 255.255.255.0* >> >> * frame-relay interface-dlci #* >> >> >> >> *From:* Amer Mustafa [mailto:[email protected]] >> *Sent:* September-01-10 5:52 PM >> *To:* Jason Maynard >> *Cc:* [email protected] >> *Subject:* Re: [OSL | CCIE_RS] Workbook 1 , LAB6 (Frame-Relay). >> >> >> >> *Nope, its not working.* >> >> >> >> *R4(config-if)#do show fram map** >> Serial0/0/0 (up): ip 150.100.100.2 dlci 412 (0x19C,0x64C0), dynamic, >> broadcast,, status defined, active >> R4(config-if)#do sh run | s Serial0/0/0 >> interface Serial0/0/0 >> ip address 150.100.24.4 255.255.255.0 >> encapsulation frame-relay >> frame-relay interface-dlci 412 >> R4(config-if)#do ping 150.100.24.2* >> >> *Type escape sequence to abort.** >> Sending 5, 100-byte ICMP Echos to 150.100.24.2, timeout is 2 seconds: >> ..... >> Success rate is 0 percent (0/5) >> R4(config-if)#* >> >> On Thu, Sep 2, 2010 at 12:44 AM, Jason Maynard <[email protected]> >> wrote: >> >> >> >> >> >> Do sh “show frame map” to see that you are missing IP to DLCI mappings >> >> >> >> Add “frame-relay interface-dlci #” command >> >> >> >> *From:* [email protected] [mailto: >> [email protected]] *On Behalf Of *Amer Mustafa >> *Sent:* September-01-10 5:41 PM >> *To:* [email protected] >> *Subject:* [OSL | CCIE_RS] Workbook 1 , LAB6 (Frame-Relay). >> >> >> >> I am on task 6.4 for LAB 6 WB1. >> >> >> >> on R4 : >> >> >> >> *R4#show run | s Serial0/0/0** >> interface Serial0/0/0 >> ip address 150.100.24.4 255.255.255.0 >> encapsulation frame-relay >> R4#ping 150.100.24.4* >> >> *Type escape sequence to abort.** >> Sending 5, 100-byte ICMP Echos to 150.100.24.4, timeout is 2 seconds: >> ..... >> Success rate is 0 percent (0/5)* >> >> >> >> on R2 : >> >> >> >> *R2(config)#do sh run | s Serial0/1/0** >> interface Serial0/1/0 >> description Frame Relay Links >> ip address 150.100.100.2 255.255.255.0 >> encapsulation frame-relay >> frame-relay map ip 150.100.100.2 205 >> frame-relay map ip 150.100.100.6 206 broadcast >> frame-relay map ip 150.100.100.5 205 broadcast >> no frame-relay inverse-arp >> interface Serial0/1/0.1 point-to-point >> ip address 150.100.24.2 255.255.255.0 >> R2(config)#do ping 150.100.24.2* >> >> *Type escape sequence to abort.** >> Sending 5, 100-byte ICMP Echos to 150.100.24.2, timeout is 2 seconds: >> ..... >> Success rate is 0 percent (0/5) >> R2(config)#* >> >> >> >> *what could be the reason ?* >> >> >> >> *======================* >> >> >> >> *regards ... * >> >> *Amer* >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> > >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
