Hi Everyone, I am doing WB 3 troubleshooting 10 section and troubleticket 4.
I got the mpls working as labels area fine across R2, R9 and R1, SHAM Links are up across the two sites running OSPF area 0 on each side. Routing tables are showning the other end prefixes. But I can not ping/telnet across the VPN, so there is no connectivity so far. Any suggestion?, I would say something in the MPLS routers is broken but labels and bindings are working as expected. I have been doing this for a while now, perhaps I am missing something basic. Any suggestion? Thanks. Francisco R2#sh mpls ldp bindings lib entry: 187.42.0.1/32, rev 2 local binding: label: 200 remote binding: lsr: 187.42.0.9:0, label: 900 lib entry: 187.42.0.2/32, rev 4 local binding: label: imp-null remote binding: lsr: 187.42.0.9:0, label: 901 lib entry: 187.42.0.6/32, rev 6 local binding: label: 201 remote binding: lsr: 187.42.0.9:0, label: 902 lib entry: 187.42.0.7/32, rev 8 local binding: label: 202 remote binding: lsr: 187.42.0.9:0, label: 903 lib entry: 187.42.0.9/32, rev 10 local binding: label: 203 remote binding: lsr: 187.42.0.9:0, label: imp-null lib entry: 187.42.19.0/27, rev 12 local binding: label: 204 remote binding: lsr: 187.42.0.9:0, label: imp-null lib entry: 187.42.29.0/27, rev 14 local binding: label: imp-null remote binding: lsr: 187.42.0.9:0, label: imp-null lib entry: 187.42.67.0/27, rev 16 local binding: label: 205 remote binding: lsr: 187.42.0.9:0, label: 904 lib entry: 187.42.69.0/27, rev 18 local binding: label: 206 remote binding: lsr: 187.42.0.9:0, label: imp-null lib entry: 187.42.69.6/32, rev 20 local binding: label: 207 remote binding: lsr: 187.42.0.9:0, label: 905 lib entry: 187.42.78.0/27, rev 22 local binding: label: 208 remote binding: lsr: 187.42.0.9:0, label: 906 lib entry: 187.42.78.8/32, rev 24 local binding: label: 209 remote binding: lsr: 187.42.0.9:0, label: 907 lib entry: 187.42.147.0/27, rev 26 local binding: label: 210 remote binding: lsr: 187.42.0.9:0, label: 908 lib entry: 187.42.212.0/27, rev 28 local binding: label: imp-null lib entry: 187.42.226.0/27, rev 30 local binding: label: 211 remote binding: lsr: 187.42.0.9:0, label: 909 R2#sh ip ospf sham-links Sham Link OSPF_SL0 to address 21.21.21.1 is up Area 0 source address 21.21.21.2 Run as demand circuit DoNotAge LSA allowed. Cost of using 1 State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Hello due in 00:00:09 R2# R2# sh ip route vrf AS245 187.42.0.0/16 is variably subnetted, 7 subnets, 2 masks C 187.42.245.0/27 is directly connected, Serial0/1/0.205 B 187.42.231.0/27 [20/0] via 187.42.19.1, 00:10:56 O 187.42.0.5/32 [110/65] via 187.42.245.5, 00:39:09, Serial0/1/0.205 O 187.42.0.4/32 [110/65] via 187.42.245.4, 00:39:09, Serial0/1/0.205 O IA 187.42.0.11/32 [110/66] via 187.42.245.5, 00:39:09, Serial0/1/0.205 O IA 187.42.0.12/32 [110/66] via 187.42.245.5, 00:39:09, Serial0/1/0.205 O IA 187.42.125.0/27 [110/65] via 187.42.245.5, 00:39:10, Serial0/1/0.205 21.0.0.0/32 is subnetted, 2 subnets B 21.21.21.1 [20/0] via 187.42.19.1, 00:10:57 C 21.21.21.2 is directly connected, Loopback21 121.0.0.0/32 is subnetted, 2 subnets B 121.121.121.1 [20/0] via 187.42.19.1, 00:10:58 C 121.121.121.2 is directly connected, Loopback22 R2#ping vrf AS245 121.121.121.1 so Serial0/1/0.205 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 121.121.121.1, timeout is 2 seconds: Packet sent with a source address of 187.42.245.2 ..... Success rate is 0 percent (0/5) R2#sh ip vrf inter Interface IP-Address VRF Protocol Lo21 21.21.21.2 AS245 up Lo22 121.121.121.2 AS245 up Se0/1/0.205 187.42.245.2 AS245 up , but be I do a show ip route vrf XX I can see the routes to the other side _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
