Tim
Are you using T Train images? Advanced IP Services or Advanced
Enterprise Services?
Ciao
Joe
On 2/24/2012 7:04 AM, Tim Miller wrote:
I have no issues on win7 64 bit, running on an i5 laptop. No sleep issues or
performance issues on 2691 and 3725s. Idlepc and Idelmax helped big time.
I used to have a lot of issues with it but I added a SSD drive to my system and
I have had 0 issues.
Sent from my iPhone
On Feb 24, 2012, at 5:21 AM, Waleed Alsherif<[email protected]> wrote:
Hi Joe ,
I would prefer to use 3725 and 2600 in the simulation , where router 3725 can simulate a
switch ( when you add NM-16ESW module ) , it is not really a switch but can support
" switchport" commands .
I am using windows XP ( Ram 4 GB / CPU AMD 4x ) and by idlepc it gets around
20% of CPU .
Also, serial interface works fine but the issue of falling asleep is coming up
occasionally.
Advice: if you have time to spend in preparing GNS3 that would be good , I
have waited 2 weeks long trying to prepare it .
You may also check something called " rednectar GNS3 workbench " someone
prepared a workbench on Ubuntu .
Best Regards
Waleed Abdulfattah Alsherif
IP and Data Network Engineer
CCIE RS (Written) / CCNP / CCNA
Mob. 002-01019556246
________________________________
From: Ben Hughes<[email protected]>
To: Joe Danrich<[email protected]>;
"[email protected]"<[email protected]>
Sent: Friday, February 24, 2012 12:03 PM
Subject: Re: [OSL | CCIE_RS] Dynamips& IPExperts .NET/Labs
Hi Joe,
I found that I was able to get a stable lab using 2961 routers in dynamips
running 12.4(9)T7. The draw back is that there are certain features that
aren't available on older code. The only routers that will run the latest code
are the 7200's. I've found them to have the falling asleep issue that you
mentioned. I recently spent about 4 days straight trying different IOS
versions and idlepc values but still no dice. I'm persevering with dynamips as
I'm hopefully near the end of the road but if I had my time again I'd find a
way to get hardware. I have wasted countless hours on issues related to
Dynamips/lab setup.
Oh, I found I had to remove the scheduler command from router configs in order
to get a stable setup. Before I did that my routers were falling over
constantly.
I haven't had any issues with serial interfaces.
Hope that helps.
cheers,
Ben.
From: Joe Danrich<[email protected]<mailto:[email protected]>>
Date: Thu, 23 Feb 2012 22:18:42 -0800
To:<[email protected]<mailto:[email protected]>>
Subject: [OSL | CCIE_RS] Dynamips& IPExperts .NET/Labs
Hi Guys
I followed with interest the various conversations of Dynamips. I am
using Dynamips with GNS3 on Kubuntu/Ubuntu 11.10 Linux, with the
IPExperts labs I have some questions on how people are running some of
the labs like VOL1 with GNS3?
Have you encountered issues with serial interfaces not coming up and
staying up with or without a clockrate applied to the applicable serial
interface?
Routers falling asleep even though the IdlePC, Idlemax idlepc are
appropriately set and overall CPU usage is approximately 60% with all
devices active?
What IOS's are people using? AIS or AES?
cheers
Joe
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
Are you a CCNP or CCIE and looking for a job? Check out
www.PlatinumPlacement.com
http://onlinestudylist.com/mailman/listinfo/ccie_rs
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
Are you a CCNP or CCIE and looking for a job? Check out
www.PlatinumPlacement.com
http://onlinestudylist.com/mailman/listinfo/ccie_rs
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
Are you a CCNP or CCIE and looking for a job? Check out
www.PlatinumPlacement.com
http://onlinestudylist.com/mailman/listinfo/ccie_rs
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
Are you a CCNP or CCIE and looking for a job? Check out
www.PlatinumPlacement.com
http://onlinestudylist.com/mailman/listinfo/ccie_rs
