Thanks Guys,
It looks that FR switch has not been configured. This is on other
vendor equipment. Proctorlabs has been booked for two weeks!
I hope you enjoy your bootcamp guys! I did mine :)
Regards,
Lukasz
On 2012-10-25 02:02, Marko Milivojevic wrote:
LMI could be purposefully misconfigured.
--
Marko Milivojevic - CCIE #18427 (SP R&S)
Senior CCIE Instructor - IPexpert
On Wed, Oct 24, 2012 at 5:43 PM, Bob McCouch <[email protected]> wrote:
Deleted PVC status would suggest the router is not hearing of this
PVC
in the LMI responses from the FR Switch. Is this in Proctor Labs, or
another environment? If your own lab or something, have you verified
that the PVC mapping does exist in the FR switch?
Check "sh frame lmi" and make sure you're really getting LMI
responses, too.
Bob
--
Sent from my iPhone, please excuse any typos.
On Oct 24, 2012, at 8:32 PM, Lukasz <[email protected]> wrote:
Hi All,
Troubleshooting part of vol3 lab3. I have checked configurations
for R5 and R6 and it looks good to me but two routers cannot
communicate. It looks that the layer 2 does not work as expected.
R6#
interface Serial0/1/0
ip address 223.5.6.6 255.255.255.224
ip pim bsr-border
ip pim sparse-mode
encapsulation frame-relay
ip ospf network point-to-point
ip ospf 1 area 569
frame-relay map ip 223.5.6.5 605 broadcast
frame-relay map ip 223.5.6.6 605
no frame-relay inverse-arp
frame-relay lmi-type cisco
end
R6(config-if)#do show frame map
Serial0/1/0 (up): ip 223.5.6.6 dlci 605(0x25D,0x94D0), static,
broadcast,
CISCO, status deleted
Serial0/1/0 (up): ip 223.5.6.5 dlci 605(0x25D,0x94D0), static,
CISCO, status deleted
R5
interface Serial0/1/0
no ip address
encapsulation frame-relay
no frame-relay inverse-arp
frame-relay lmi-type cisco
interface Serial0/1/0.56 point-to-point
ip address 223.5.6.5 255.255.255.224
ip pim bsr-border
ip ospf network point-to-point
ip ospf 1 area 569
snmp trap link-status
frame-relay interface-dlci 506
R5#show frame map
Serial0/1/0.56 (down): point-to-point dlci, dlci 506(0x1FA,0x7CA0),
broadcast
status deleted
R5#
R5#
Is there anything wrong with that config?
Regards
Lukasz
_______________________________________________
For more information regarding industry leading CCIE Lab training,
please visit www.ipexpert.com
Are you a CCNP or CCIE and looking for a job? Check out
www.PlatinumPlacement.com
http://onlinestudylist.com/mailman/listinfo/ccie_rs
_______________________________________________
For more information regarding industry leading CCIE Lab training,
please visit www.ipexpert.com
Are you a CCNP or CCIE and looking for a job? Check out
www.PlatinumPlacement.com
http://onlinestudylist.com/mailman/listinfo/ccie_rs
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
Are you a CCNP or CCIE and looking for a job? Check out
www.PlatinumPlacement.com
http://onlinestudylist.com/mailman/listinfo/ccie_rs
