I have a dumb question. Have you tried the same console setup with a different device? i.e. some other switch or router? Does it work there?
Cheers, Matt CCIE #22386 CCSI #31207 On 10 Nov 2013, at 5:35 pm, Wilberth E. Lemaître <[email protected]> wrote: > Hi, > No, I installed Ubuntu and I run minicom and nothing, I also installed > TeraCom on my Windows machine, it is not working either. Does anybody knows > how to reset the console port if I open the switch? or something similar, I > don't know, I am just making up stupid ideas, I am desperated cause my > studies are stuck because of my 3550. Any other idea? > Thanks > From: [email protected] > To: [email protected] > CC: [email protected] > Subject: RE: [OSL | CCIE_RS] Console problem with 3550 > Date: Sat, 9 Nov 2013 21:11:18 -0600 > > > > > Hi Arya, > No, I haven't done that, I have running windows 8 on my laptop and PC, I was > searching in the internet something similar, I guess the best way to test it > out is to create a VM and execute it from there. I did enable and disable XON > and XOFF still nothing.I will let you know the result after the VM is created > and if it works.Thanks a lot for your help. > Wilberth > > Date: Sat, 9 Nov 2013 20:30:43 -0600 > Subject: Re: [OSL | CCIE_RS] Console problem with 3550 > From: [email protected] > To: [email protected] > CC: [email protected] > > In this case it seems problem is related to flow control. You should try flow > control on/off. > > Have you tried windows hyperterm application apart from putty and securecrt.? > > > > > On Sat, Nov 9, 2013 at 8:27 PM, Wilberth LeMaître > <[email protected]> wrote: > > > > > > > > > Hi, > > > > It seems to be that people is not reading properly or my English is not good > enough. Arya, the procedure you are telling me I already did it, as you can > read on my problem description, it says: I broke out the boot process to > delete the config.txt because > sometimes the speed console changes when you do an upgrade or whatever via > the console, but this time, NOT even in switch: mode is letting me hit enter. > > > > Sent from HP Slate 7 > > > > Ramcharan Arya <[email protected]> wrote: > > > > > > > > > > > > > > > > Hi, > > > > You can change switch BAUD rate by using below procedure. > > > > > 1. Power off the switch > > > 2. Press the system button and power on the switch and keep system button > hold for 30 sec > > > > > type > > > flash_init > > > load_helper > > > delete configuration file > > > > > reset the switch > > > > > change baud rate on switch as per below procedure > > > > > > http://www.cisco.com/en/US/products/hw/routers/ps259/products_tech_note09186a008015bfac.shtml#download_2620 > > > > > > This will allow you to change buad rate to 9600 so you can see logs on hyper > term session. > > > > > Thanks, > > Ramcharan Arya > > CCIE # 28926 ( Voice/Routing & Switching) > > > > > > > > > On Sat, Nov 9, 2013 at 12:22 PM, Wilberth E. Lemaître > <[email protected]> wrote: > > > Hello Community, > > I am having a strange issue with my Switch 3550. I updated the IOS and I > changed the Console BAUD to 115200 then I put it back to 9600 when the > upgrade was successful. I turned it on ago normally and now either 115200 or > 9600 speed is not working, I tried SecureCRT, > putty, I changed the console cable, everything. The weirdest thing is that > when I set the speed in 9600 in SecureCRT or putty, I can see while the > switch boots up which means the switch is working perfectly but when it says > press RETURN to get started I hit > enter and nothing happens, absolutely nothing. I broke out the boot process > to delete the config.txt because sometimes the speed console changes when > you do an upgrade or whatever via the console, but this time not even in > switch: mode is letting me hit enter. > I know the switch is working properly because if I connect a cable to f0/0 I > can see the logging message on my screen when it comes up (this is in 9600 > speed in SecureCRT) Now, is there any other way t > > o reset the BAUD of the console? Any other idea to get into the switch? Or if > this is a bug, how can it be solved? > > Best regards,Wilberth > > _______________________________________________ > > For more information regarding industry leading CCIE Lab training, please > visit > www.ipexpert.com > > > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com > > > > http://onlinestudylist.com/mailman/listinfo/ccie_rs > > > > > > > > > > > > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com > > http://onlinestudylist.com/mailman/listinfo/ccie_rs _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
