Willians,
http://www.cisco.com/en/US/docs/ios/ipapp/command/reference/iap_i1.html#wp10 52220 Transit entries are those that do not match any of the filters specified by ip accounting-list global configuration commands. If no filters are defined, no transit entries are possible. To maintain accurate accounting totals, the Cisco IOS software maintains two accounting databases: an active and a checkpointed database. What you are seeing below is correct. Sorry I had to look back at the question to remember what the question asked. The Transit table is what is not kept. Regards, Tyson Scott - CCIE #13513 R&S and Security Technical Instructor - IPexpert, Inc. Telephone: +1.810.326.1444 Cell: +1.248.504.7309 Fax: +1.810.454.0130 Mailto: [email protected] Join our free online support and peer group communities: <http://www.IPexpert.com/communities> http://www.IPexpert.com/communities IPexpert - The Global Leader in Self-Study, Classroom-Based, Video On Demand and Audio Certification Training Tools for the Cisco CCIE R&S Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE Storage Lab Certifications. From: [email protected] [mailto:[email protected]] On Behalf Of Willians Barboza Sent: Monday, May 04, 2009 8:50 PM To: [email protected] Subject: [OSL | CCIE_Security] Fwd: IP accounting Indeed I was trying using dynamips... Now I am trying at Cisco Partner E-learning connection... Using the topology for the following lab "SNRS - Configure a DMVPN" ip accounting-threshold 500 ip accounting-list 172.31.235.93 0.0.0.0 ip accounting-transits 50 interface FastEthernet0/0 ip address 10.1.1.1 255.255.255.0 ip accounting output-packets ip accounting precedence input duplex auto speed auto ! interface FastEthernet0/1 ip address 172.31.235.21 255.255.255.0 ip accounting output-packets ip accounting precedence input duplex auto speed auto So i tryind to ping 10.1.1.3, which is behind this router from 2 different IP addresses. However, it accounts for both addresses Central_site#sh ip accounting Source Destination Packets Bytes 10.1.1.3 172.31.235.93 4 400 172.31.235.93 10.1.1.3 4 400 10.1.1.3 172.31.235.55 4 400 172.31.235.55 10.1.1.3 4 400 Accounting data age is 4 And this is the version used Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(15)T, RELEASE SOFTWARE (fc3) Then, I checked the Cisco documentation and it states exactly the opposite. The ip accounting-list is used to configure the hosts for which accounting information will be kept. http://www.cisco.com/en/US/docs/ios/ipapp/command/reference/iap_i1.html#wp10 51784 The following example adds all hosts with IP addresses beginning with 192.31 to the list of hosts for which accounting information will be kept: ip accounting-list 192.31.0.0 0.0.255.255 Anyways, it didn't work either... 2009/5/4 Tyson Scott <[email protected]> Are you using dynamips? If so don't always expect the same results. Sometimes it has quirks. Regards, Tyson Scott - CCIE #13513 R&S and Security Technical Instructor - IPexpert, Inc. Telephone: +1.810.326.1444 Cell: +1.248.504.7309 Fax: +1.810.454.0130 Mailto: [email protected] Join our free online support and peer group communities: <http://www.ipexpert.com/communities> http://www.IPexpert.com/communities IPexpert - The Global Leader in Self-Study, Classroom-Based, Video On Demand and Audio Certification Training Tools for the Cisco CCIE R&S Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE Storage Lab Certifications. From: [email protected] [mailto:[email protected]] On Behalf Of Willians Barboza Sent: Monday, May 04, 2009 7:51 PM To: OSL Security Subject: [OSL | CCIE_Security] IP accounting Hi all, I am trying do do lab6 for V3 and I got stuck in this question. First of all, I am using the following IOS version: 3700 Software (C3745-ADVENTERPRISEK9-M), Version 12.4(15)T8, RELEASE SOFTWARE (fc3) I confgured the following as stated in the proctor guide. (I just changed the serial interface) ip accounting-threshold 500 ip accounting-list 5.5.5.5 0.0.0.0 ip accounting-transits 50 Serial0/0.6 ip accounting output-packets ip accounting precedence input FastEthernet0/1 ip accounting output-packets ip accounting precedence input however, whenever I try to check the show ip accounting command, the host 5.5.5.5 is still shown. R4#sh ip accounting Source Destination Packets Bytes 2.2.2.2 6.6.6.6 7 672 6.6.6.6 2.2.2.2 7 672 2.2.2.2 5.5.5.5 105 10480 5.5.5.5 2.2.2.2 105 10480 Accounting data age is 10 Any guesses??
