Thanks, Tyson.
Am 19.06.2009 um 01:58 schrieb Tyson Scott:
Simon,
I looked at the solution guide tonight and what is in the solution
guide is
the correct answer.
Regards,
Tyson Scott - CCIE #13513 R&S and Security
Technical Instructor - IPexpert, Inc.
Telephone: +1.810.326.1444
Cell: +1.248.504.7309
Fax: +1.810.454.0130
Mailto: [email protected]
Join our free online support and peer group communities:
http://www.IPexpert.com/communities
IPexpert - The Global Leader in Self-Study, Classroom-Based, Video
On Demand
and Audio Certification Training Tools for the Cisco CCIE R&S Lab,
CCIE
Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE
Storage
Lab Certifications.
-----Original Message-----
From: Tyson Scott [mailto:[email protected]]
Sent: Friday, June 12, 2009 8:16 PM
To: 'Simon Baumann'
Cc: '[email protected]'
Subject: RE: [OSL | CCIE_Security] Lab2: task 2.7, stateful NAT
It is. It should only be one line.
Regards,
Tyson Scott - CCIE #13513 R&S and Security
Technical Instructor - IPexpert, Inc.
Telephone: +1.810.326.1444
Cell: +1.248.504.7309
Fax: +1.810.454.0130
Mailto: [email protected]
Join our free online support and peer group communities:
http://www.IPexpert.com/communities
IPexpert - The Global Leader in Self-Study, Classroom-Based, Video
On Demand
and Audio Certification Training Tools for the Cisco CCIE R&S Lab,
CCIE
Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE
Storage
Lab Certifications.
-----Original Message-----
From: Simon Baumann [mailto:[email protected]]
Sent: Friday, June 12, 2009 6:42 PM
To: Tyson Scott
Cc: [email protected]
Subject: Re: [OSL | CCIE_Security] Lab2: task 2.7, stateful NAT
Thanks Tyson.
The PG has the solution you mentioned. I wonder if the requirement
"10.0.146.14 to 9.16.145.14"
is also covered with this config?
Cheers
Simon
Am 12.06.2009 um 19:47 schrieb Tyson Scott:
Simon,
If that is what is in the configuration it is a mistake. If you
look in the
final configurations you will find the following.
ip nat inside source static network 10.0.146.0 9.16.146.0 /24
mapping-id 10
The above is the correct answer.
Regards,
Tyson Scott - CCIE #13513 R&S and Security
Technical Instructor - IPexpert, Inc.
Telephone: +1.810.326.1444
Cell: +1.248.504.7309
Fax: +1.810.454.0130
Mailto: [email protected]
Join our free online support and peer group communities:
http://www.IPexpert.com/communities
IPexpert - The Global Leader in Self-Study, Classroom-Based, Video
On Demand
and Audio Certification Training Tools for the Cisco CCIE R&S Lab,
CCIE
Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE
Storage
Lab Certifications.
-----Original Message-----
From: [email protected]
[mailto:[email protected]] On Behalf Of Simon
Baumann
Sent: Friday, June 12, 2009 5:36 AM
To: [email protected]
Subject: [OSL | CCIE_Security] Lab2: task 2.7, stateful NAT
Hi,
task 2.7 asks: "10.0.146.14 should be translated to 9.16.146.14. In
addition configure R1 and R6 to NAT the rest of the 10.0.146.0/24
network to 9.16.146.0/24.
This should be completed in as few commands as possible and should
support inbound connection."
To my knowledge, we should need two statics: one for the
10.0.146.14 -
9.16.146.14 and another for the 10.0.146.0/24 -> 9.16.146.0/24,
right?
The PG only lists the last mentioned static. Could I add an more
specific static without loosing points like:
ip nat inside source static 10.0.146.14 9.16.146.14 mapping-id 10
I'm a little bit puzzled with that. Thanks!
Chers
Simon
